CADPXS FEONIXS Operation manual

INSTALLATION, OPERATION
& SERVICE INSTRUCTIONS
Why home dehumidification is important. At CADPXS we
believe Healthy Air is essential– especially inyour
home.

TABE OF CONTENTS

• The appliance is only designed to be USED INDOORS.
•If being used in a wet area, plug it into a GROUND FAULT
INTERRUPTER.
• DO NOT use the appliance as a bench or table.
• The appliance must always be used in a horizontal position.
• The appliance is not being used above the elevation level of over
2000 m (6562 ft.)
Read the operation and maintenance instructions carefully before
using this unit. Proper adherence to these instructions is essential
to obtain maximum benefit from your FEONIXS dehumidifier.
• It is designed to be used INDOORS ONLY.
• DO NOT use the FEONIXS as a bench or table.
• It must always be used in the upright position.
• If used in a wet area, plug it into a GROUND FAULT INTERRUPTER.
-1-
CAUTIONARY WARNING
WARNING

FEONIXS is a highly power dehumidifier created by a company
dedicated to achieving maximum humidity in an ultra-space-saving
design. These machines deliver optimum results even in the
toughest water restoration environments. With Low Energy input
and is very lightweight. It excels in delivering high-performance
results of 85 Pints per Day.
CADPXS has brought quite an amazing set of Dehumidifiers, the
FEONIXS, integrated with handle and wheels support and equipped
with onboard storage and condensate hose. Although compact in
size, these dehumidifiers deliver great humidity settings for any
room with a top of the notch control panel that can instantly detect
the room and provide instant feedback. With a superior stacking
and a heavy-duty condensate pump. These stackable dehumidifiers
are the best drying system.
INTRODUCTION
Outlet Requirement: 3-Prong
Power Supply: 110-120 VAC, Grounded
Circuit protector: 15 Amp
ELECTRICAL SUPPLY
Unit Size: 21.2×11.6×17.4 in
Unit Weight: 62.8 lbs
Water Removal: 85 pints/day @ AHAM (80°F, 60%)
Water Removal 13.39 gal/day maximum @ AHAM
Blower: 210 CFM
Functioning Humidity Range: 25-80%
Operating Range: 35.6°F-105°F
Filter: 9.5×10.6×0.4 Pleated Media MERV-8
Power: 5.82 amps
SPECIFICATIONS
Note: specifications subject to change without notice.
-2-

• The location should have power outlet at about 6 meters of the
device as that is the length of the cord.
Selecting the Location
• Place the Unit in an Upright Position.
• The location of the operation should be an enclosed area.
• The location should allow constant air circulation.
• Keep the Dehumidifier away from any moisture-laden air in the
working area.
Connect the plug of the connector of the power to the power outlet
of the appliance.
Power cord Installation
INSTALLATION AND OPERATION GUIDE
Drain Hose Installation
1.Attach the hose inlet to the
drain outlet located on the
graph appliance.
2.Allow the hose to be set off to a drain or a sink or even to a
container that can collect the discharged water.
OPERATION
-3-

1.When the unit is plugged in you will see
the CADPXS LOGO.
2.The display will inform the machine is in
shutdown mode, press the “Power button” to
turn on.
3.When the machine is in dehumidification
mode, the display will show:
Out: Temperature, Humidity, GPP of the current outlet. GPP=
Grains per pound (GR/LB).
Set: The humidity value currently Set (the machine will stand
by after the humidity reaches the Set value).
In: Temperature, Humidity, GPP of the current inlet. GPP=
Grains per pound (GR/LB).
Job hours and Life hours display.
Press the POWER button to turn the dehumidifier ON and
OFF.
Press the PURGE button to purge the machine.
Press the MENU button to advance to the next screen or to
enter a value.
Press the SET button to scroll through available values.
STARTUP
-4-

4. 1 Press the MENU butt on to ent er the
sub m e nu. De vice name di splayed on the
s c r e e n . G o t o t h e A P P t o c h a n g e o n l y
applicable to an app-controlled dehumidifier.
Press the MENU button to confirm selection
and advance to the next screen.
4.2 Display the working hours of this time.
Press the MENU button to confirm selection
and advance to the next screen.
4.3 The screen displays the Coil temp. Press
the MENU button to confirm selection and
advance to the next screen.
4.4 Wifi Hotspot: Factory setting is "OFF",
press “set button” to enable Wifi hotspot and
switch ON/OFF. The device can transmit data
and receive APP commands. The icon flickers
when connected to the main interface. After a
s u c c e s s f u l co n n e c t i o n , t h e i c o n d i s p l a y s
normally. Only applicable to APP-controlled
dehumidifier. Press the MENU button to confirm
selection and advance to the next screen.
4.5 Press the “power button” to turn off the
dehumidifier, the dehumidifier will go through
a shutdown cycle.
The shutdown cycle can be adjusted according
to "Settings", and the shutdown cycle can be
adjusted from 3 minutes to 20 minutes to
better drain the water.
-5-

4.6 Pr e s s the Se t button to t oggle th e
temperature units between  and . Press
the MENU button to confirm selection and
advance to the next screen.
4.7 Press the “Set button” to switch GPP units
between gr/lb. or gr/kg. Press the “MENU
button” to confirm the selection and advance
to the next screen. GPP= Grains per pound
(GR/LB).
4.8 Press the “Set button” to adjust the set
point RH% in 5% increments ranging from 25
to 80% RH. and then loop back to CO. Adjust
to CO mode, dehumidifier always running.
Press the “MENU button” to confirm selection
and advance to the next screen.
4.9 The display prompts the user that the
defrost cycle is in progress.
The defrosting status is displayed on the main
i n t e r f a c e a s a fl a s h i n g i c o n u n t i l t h e
defrosting ends and the defrosting lamp
disappears. In the meantime, please wait
patiently for the machine to finish frosting.
5 . 0 T h e c o m p r e s s o r i s i n a p r o t e c t i v e
condit ion. Du ring this perio d, plea se be
patient and wait for the countdown to end.
The dehumidifier will automatically turn on
after the countdown.
-6-

TROUBLESHOOTING
Solution: Verify th a t t h e pump is pr o p e r l y i n s t alled and
functioning. If so, unplug the unit for two minutes, then restart.
E4: Problem with Pump
Solution: Check to ensure that the sensor wire is connected at
both ends, if no issues are visible, the sensor may be faulty.
E1: Humidity Sensor or Communication Error
Solution: Increase the room temperature so it is within operation
range (above 35.6). If error is still displayed, check the sensor.
HI: Room Temperature is above 105
Solution: Decrease the room temperature so it is within operating
range (below 105). If error is still displayed, check the sensor.
E5: Refrigerant Leak
Solution: Contact us for Assistance.
LO: Room Temperature is below 35.6
-7-
5.1 When the purge button is pressed the
display will tell the user on the dashboard that
the pump is draining and display a 30-second
countdown timer. Until the machine finishes
draining, the display will also prompt the user
on the dashboard that the machine is draining
a u t o m a t i c a l l y, a n d d i s p l ay a 30 - s e c o n d
countdown.
If the machine has an error and needs
service, the onboard control system will
display a diagnostic code. If E1, E4, HI or
LO is displayed on the vehicle control
screen, please refer to the following:

1. Unplug the unit.
4 . C l e a n t h e fi l t e r m e s h b y
vacuuming it or washing with warm
water (no soap or cleaners). Gently
shake the filter dry then reinsert it.
There is dirt or buildup, replace the
filter.
Filter Maintenance
3. Check the filter for dirt and
buildup.
2. Slide-out the filter from the side.
MAINTENANCE
Wi-Fi connection successful.
Hotspot direct successful icon.
Connection to server failed.
-8-
• Always store the machine in a day and cool indoor place, away
from sunlight as well as chemicals and out of children’s reach.
Unit Maintenance
• Always clean the surface of the housing with a damp cloth. Do not
clean with water directly.