CADPXS XDRYMAX User manual

USER MANUAL
MODEL: XDRYMAX
4007648
Intertek
US
C
SUPERIOR PERFORMANCE,
PORTABLE DESIGN.

TABE OF CONTENTS

• The appliance is not being used above the elevation level of over
2000 m (6562 ft.)
• The appliance is only designed to be USED INDOORS.
•If being used in a wet area, plug it into a GROUND FAULT
INTERRUPTER.
• DO NOT use the appliance as a bench or table.
• The appliance must always be used in a horizontal position.
Read the operation and maintenance instructions carefully before
using this unit. Proper adherence to these instructions is essential
to obtain maximum benefit from your XDRYMAX dehumidifier.
• It is designed to be used INDOORS ONLY.
• If used in a wet area, plug it into a GROUND FAULT INTERRUPTER.
• It must always be used in the upright position.
• DO NOT use the XDRYMAX as a bench or table.
-1-
CAUTIONARY WARNING
WARNING

XDRYMAX is a highly power dehumidifier created by a company
dedicated to achieving maximum humidity in an ultra-space-
saving design. These machines deliver optimum results even in the
toughest water restoration environments. With Low Energy input
and is very lightweight. It excels in delivering high-performance
results of 85 Pints per Day.
CADPXS has brought quite an amazing set of Dehumidifiers, the
XD RYMAX, integrat ed with handle and wheels su pport an d
equipped with onboard storage and condensate hose. Although
compact in size, these dehumidifiers deliver great humidity
settings for any room with a top of the notch control panel that can
instantly detect the room and provide instant feedback. With a
superior stacking and a heavy-duty condensate pump. These
stackable dehumidifiers are the best drying system.
INTRODUCTION
Power Supply: 110-120 VAC, Grounded
Outlet Requirement: 3-Prong
Circuit protector: 15 Amp
ELECTRICAL SUPPLY
Unit Size: 21.2 × 11.6 × 17.4 in
Blower: 210 CFM
Power: 5.82 amps
Water Removal: 85 pints/day @ AHAM (80°F, 60%)
Water Removal 13.39 gal/day maximum @ AHAM
Functioning Humidity Range: 25-80%
Operating Range: 35.6°F-105°F
Filter: 9.5×10.6×0.4 Pleated Media MERV-10
Unit Weight: 62.8 lbs
SPECIFICATIONS
Note: specifications subject to change without notice.
-2-

• The location should allow constant air circulation.
Selecting the Location
• Keep the Dehumidifier away from any moisture-laden air in the
working area.
• The location of the operation should be an enclosed area.
• Place the Unit in an Upright Position.
• The location should have power outlet at about 6 meters of the
device as that is the length of the cord.
Connect the plug of the connector of the power to the power outlet
of the appliance.
Power cord Installation
INSTALLATION AND OPERATION GUIDE
Drain Hose Installation
1.Attach the hose inlet to the
drain outlet located on the
graph appliance.
2.Allow the hose to be set off to a drain or a sink or even to a
container that can collect the discharged water.
OPERATION
-3-

1.When the unit is plugged in you will see
the CADPXS LOGO.
2.The display will inform the machine is in
shutdown mode, press the “Power button” to
turn on.
3.When the machine is in dehumidification
mode, the display will show:
In: Temperature, Humidity, GPP of the current inlet. GPP=
Grains per pound (GR/LB).
Out: Temperature, Humidity, GPP of the current outlet. GPP=
Grains per pound (GR/LB).
Set: The humidity value currently Set (the machine will stand
by after the humidity reaches the Set value).
Job hours and Life hours display.
Press the POWER button to turn the dehumidifier ON and OFF.
Press the MENU button to advance to the next screen or to enter
a value.
Press the PURGE button to purge the machine.
Press the SET button to scroll through available values.
STARTUP
-4-

4.1 Press the MENU button to enter the
su bmenu. D ev ic e name displayed on the
s c r e e n . G o t o t h e A P P t o c h a n g e o n l y
applicable to an app-controlled dehumidifier.
Press the MENU button to confirm selection
and advance to the next screen.
4.2 Display the working hours of this time.
Press the MENU button to confirm selection
and advance to the next screen.
4.3 The screen displays the Coil temp. Press
the MENU button to confirm selection and
advance to the next screen.
4.4 Wifi Hotspot: Factory setting is "OFF",
press “set button” to enable Wifi hotspot and
switch ON/OFF. The device can transmit data
and receive APP commands. The icon flickers
when connected to the main interface. After a
s u c c e s s f u l c o n n e c t i o n , t h e i c on d i s p l a y s
normally. Only applicable to APP-controlled
dehumidifier. Press the MENU button to confirm
selection and advance to the next screen.
4.5 Press the “power button” to turn off the
dehumidifier, the dehumidifier will go through
a shutdown cycle.
The shutdown cycle can be adjusted according
to "Settings", and the shutdown cycle can be
adjusted from 3 minutes to 20 minutes to
better drain the water.
-5-

4.6 Press the Set button to toggle the
temperature units between  and . Press
the MENU button to confirm selection and
advance to the next screen.
4.7 Press the “Set button” to switch GPP
units between gr/lb. or gr/kg. Press the
“MENU button” to confirm the selection and
advance to the next screen. GPP= Grains per
pound (GR/LB).
4.8 Press the “Set button” to adjust the set
point RH% in 5% increments ranging from 25
to 80% RH. and then loop back to CO. Adjust
to CO mode, dehumidifier always running.
Press the “MENU button” to confirm selection
and advance to the next screen.
4.9 The display prompts the user that the
defrost cycle is in progress.
The defrosting status is displayed on the
main interface as a flashing icon until the
defrosting ends and the defrosting lamp
disappears. In the meantime, please wait
patiently for the machine to finish frosting.
5 . 0 T h e c o m p r e s s o r i s i n a p r o t e c t i v e
condition. During this period, please be
patient and wait for the countdown to end.
The dehumidifier will automatically turn on
after the countdown.
-6-

TROUBLESHOOTING
E1: Humidity Sensor or Communication Error
Solu tion : Ve rify t h at the pump is prop erly inst a lled and
functioning. If so, unplug the unit for two minutes, then restart.
E4: Problem with Pump
Solution: Check to ensure that the sensor wire is connected at
both ends, if no issues are visible, the sensor may be faulty.
Solution: Contact us for Assistance.
Solution: Decrease the room temperature so it is within operating
range (below 105). If error is still displayed, check the sensor.
E5: Refrigerant Leak
Solution: Increase the room temperature so it is within operation
range (above 35.6). If error is still displayed, check the sensor.
HI: Room Temperature is above 105
LO: Room Temperature is below 35.6
-7-
5.1 When the purge button is pressed
the d i splay w i l l t e l l t h e u s e r on t h e
dashboard that the pump is draining and
display a 30-second countdown timer. Until
the machine finishes draining, the display
will also prompt the user on the dashboard
that the machine is draining automatically,
and display a 30-second countdown.
If the machine has an error and needs
service, the onboard control system will
display a diagnostic code. If E1, E4, HI or
LO is displayed on the vehicle control
screen, please refer to the following:

Filter Maintenance
2. Slide-out the filter from the side.
1. Unplug the unit.
3. Check the filter for dirt and
buildup.
4 . C l e a n t h e fi l t e r m e s h b y
vacuuming it or washing with warm
water (no soap or cleaners). Gently
shake the filter dry then reinsert it.
There is dirt or buildup, replace the
filter.
• Always clean the surface of the housing with a damp cloth. Do not
clean with water directly.
• Always store the machine in a day and cool indoor place, away
from sunlight as well as chemicals and out of children’s reach.
Unit Maintenance
MAINTENANCE
Wi-Fi connection successful.
Hotspot direct successful icon.
Connection to server failed.
-8-