Cagebot MINIQUAD User manual
®
MINIQUAD
Other languages available at / 以下提供其他語言 /此安装说明书亦提供中文版本 /
Andere Sprachen verfügbar unter: www.cagebot.com
assembly Manual
2
1.
2.
Additionally, you will need:
or
8xAA 1,5V Batteries
Important: Do not mix rechargeable and non-
rechargeable batteries!
CAGEBOT NOTICE
Hot-plugging can damage
electronic components
When connecting electronic components the controller needs to be switched o (the light
of the LED on top of the controller needs to be o), otherwise, the electronic components
may be damaged.
Connecting non-Cagebot
electronic components
Connecting non-Cagebot electronic components is possible, but is done on your own risk.
In case of damage the warranty expires.
3
14+
Warnung! Nicht für Kinder unter 14 Jahren geeignet. Für Kinder unter
14 Jahren Benutzung nur unter Aufsicht von Erwachsenen.
Warning! Not suitable for children under 14 years of age. For children
unter 14 years of age, usage under parental guidance or guidance of
adults only.
警告!十四歲以下的孩童需由家長陪同或成年人士引導下使用。
警告!十四岁以下的孩童需由家长陪同或成年人士引导下使用。
Achtung! Erstickungsgefahr! Für Kinder unter 3 Jahren nicht geeignet.
Warning! Choking hazard. Small parts. Not suitable for children under
3 years of age.
警告!內含細小零件，若吞嚥恐引發窒息危險，不適合三歲以下幼童。
警告!內含細小零件，若吞嚥恐引发窒息危险，不适合三岁以下幼童。
SICHERHEITSHINWEISE
SAFETY INFORMATION
重要安全資訊
重要安全资讯
4
ATTENTION, IMPORTANT SAFETY INFORMATION!
Regularly check all component for damages. Stop using damaged
parts and components, and replace them immediately. This is
especially important with regards to all electronic components.
Store out of reach of children under 14 years of age. Let children
under 14 years of age use the product or parts of the product
under parentel supervision or under supervision of adults only.
Watertightness
Thesetisoutdoor-suitableandrobust,butitselectricalcomponents
are NOT WATERTIGHT. Improper use may damage the electric
system.
Risk of injury
Extreme and sudden stress on the product or parts of it, fatigue
phenomena as well as damaged and defective material can lead
to components breaking or detaching. This can lead to injuries.
Bruise
Careless handling can cause ngers or skin being caught between
components. This can lead to major bruises at aected body parts.
Acute risk of injury caused by hot surfaces!
Careless handling can lead to a rise of surface temperature of the
heat sink of > 80 °C. Risk of burning! The heat sink should not be
touched during usage and shortly after usage.
Important information about batteries
Never use damaged batteries. Only use batteries of the type
recommended, or a corresponding type. Insert the batteries
so that the poles are correctly positioned. Never short-circuit
the battery holder. Incorrect handling of batteries or the use of
inappropriate energy sources can lead to damages of the robot
and electronic components and to serious injuries.
Disposal
Protect the environment by not disposing of this product with your
household waste (2002/96/EC). Check with your local authority for
recycling advice and facilities.
5
parts LIst
Order numberAmountNameImage
1002_070NK_042Arc 70mm
1001_030NR_042Bar 30mm
1001_030NK_0419Bar 30mm
1001_050NR_041Bar 50mm
1001_110NK_046Bar 110mm
1003_004AN_044Adapter single
1003_004AN_0410Adapter double
1003_031NK_0410Connector 3 arms angled
1004_007SN_0432Cagebot nut
1004_110SN_0484Countersunk screw M3x10
1004_106SN_0424Countersunk screw M3x6
1004_210SN_042Cylinder screw M3x10
1005_515SN_042Cagebot axle x 15mm
6
parts LIst
Order numberAmountNameImage
1007_079RK_044Tire 70mm
1007_070NR_044Rim 70mm
1009_001NK_042Friction bearing
1009_006PK_042Clutch shaft 6mm
1005_001NK_042Shaft end adapter
1009_100PK_042Clutch clamp ring
1006_250NK_042Motor holder angled 50mm
2020_035NK_042Motor 30mm (35:1)
2021_001NK_041Cagebot Controller
1025_003XX_041Batterie holder
2025_001YK_041Battery box body
1025_002YK_041Battery box lid
7
contents
Basics & Tips 8
Assembly Instructions 9
1. Front Wheels 9
2. Rear Wheels 10
3. Chassis 11
Cables 27
8
ba
basics & tips
Before you get started, here a few basics and tips for the assembly of
the Cagebot.
1. Concept of Assembly
2. Screws
The screws should be fastened tightly but not too tightly to avoid damages.
Also, please note that screws should be inserted through holes with
depressions on the sides of a bar:
3. Follow the instructions closely
Please follow the assembly instructions closely to avoid excess assembly
time. Pay special attention to the bars' orientation and from which direction
to insert the screws!
Now you are ready! Have fun! The Cagebot Team
9
a
2x
b
Use short countersunk screws (M3x6)!
1. front wheels
10
2x
ba
c D
2x
Do not bolt down cylinder screw!
Use short countersunk screws (M3x6) und cylinder scews (M3x10)!
Mind the orientation of arrow and recess!
2. rear wheels
Table of contents
