CalderaSpas Geneva User manual

• GenevaTM • Niagara
®
• Tahitian
®
• Elation
®
• Aspire
®
• Moorea®• Hawaiian • Martinique
®
• Kauai
®
• Olympia •
Cumberland
®
• Aventine
®
Caldera 50Hz
Owner’s Manual

OWNER’S MANUAL
This Owner’s Manual will acquaint you with the operation and general maintenance of your new spa. We suggest that you
take some time to carefully review all sections. Please keep this manual available for reference.
If you have any questions about any aspect of your spa’s set-up, operation or maintenance, contact your authorized Caldera
dealership. They are trained professionals who are familiar with the product as well as new spa ownership concerns. Their
expertise will facilitate the enjoyment of your new Caldera spa.
The serial number/identification label is located within the equipment compartment of your Caldera spa. The serial number
should also be documented on the delivery receipt from your dealer.
IMPORTANT: Watkins Manufacturing Corporation reserves the right to change specifications, or design, without notification
and without incurring any obligation.
DATE PURCHASED: ________________________________________
DATE INSTALLED: ____________________________________________
DEALER: ____________________________________________________
ADDRESS: __________________________________________________
TELEPHONE: ________________________________________________
SPA MODEL/SERIAL NUMBER: ______________________________
COVER SERIAL NUMBER: ____________________________________
In most cities and counties, permits will be required for the installation of electrical circuits or the construction of exterior surfaces (decks and gazebos).
In addition, some communities have adopted residential barrier codes which may require fencing and/or self-closing gates on the property to prevent
unsupervised access to a pool (or spa) by children under 5 years of age. Your Caldera spa is equipped with a locking cover that meets the ASTM
F1346-91 Standard for Safety Covers, and as a result, is usually exempt from most barrier requirements. As a general practice, your local Building
Department will inform you of any applicable barrier requirements at the time a permit is obtained for the installation of an electrical circuit. Your Caldera
dealer can provide information on which permits may be required.
WELCOME
Watkins®Manufacturing Corporation congratulates you on your decision to enjoy the finest spa
available... Welcome to the growing family of Caldera Spa owners.
NOTE: This is an example. Your spa’s
label will contain different information.
Peel off top sticker and place here.
MODEL: GENEVA
SERIES: UTOPIA
SERIAL: GEBE1K1001
RATINGS: 240V, 50Hz, 25A
1280 Park Center Dr., Vista, CA 92081
WatkinsManufacturing Corp.
GEBE1K1001
GEBE1K1001
GEBE1K1001
GEBE1K1001

TABLE OF CONTENTS
SAFETY INSTRUCTIONS
• Important Safety Instructions ...................................................................... 1
• Important Spa Instructions .......................................................................... 3
INSTALLATION
• Site Preparation ............................................................................................ 3
• Outdoor and Patio Installation .................................................................... 3
• Deck Installation............................................................................................ 4
• Indoor/Basement Installation ...................................................................... 4
• Ground and Spa Leveling Preparation ........................................................ 4
• Delivery Access ............................................................................................ 4
• Spa Cover Installation .................................................................................. 5
DIMENSIONS
• GenevaTM and Niagara®................................................................................6
• Tahitian®, Hawaiian, and Aspire®................................................................7
• Elation®..........................................................................................................8
• Moorea®........................................................................................................9
• Martinique®..................................................................................................10
• Kauai®..........................................................................................................11
• Olympia........................................................................................................12
• Cumberland®..............................................................................................13
• Aventine®....................................................................................................14
CONTROLS AND EQUIPMENT
• Geneva ........................................................................................................15
• Niagara ........................................................................................................16
• Tahitian ........................................................................................................17
• Elation ..........................................................................................................18
• Aspire ..........................................................................................................19
• Moorea ........................................................................................................20
• Hawaiian ......................................................................................................21
• Martinique ..................................................................................................22
• Kauai ..........................................................................................................23
• Olympia........................................................................................................24
• Cumberland and Aventine ........................................................................25
ELECTRICAL INSTALLATION
• Electrical Requirements and Precautions..................................................26
START-UP AND REFILL PROCEDURES .......29
CUSTOMIZING YOUR MASSAGE
• Diverter Valves ............................................................................................ 31
• Acquarella®Waterfall Valve........................................................................ 31
• Atlas®Neck Jet Valve..................................................................................31
• Air Controls..................................................................................................31
• Hydro Jets ..................................................................................................31
• Air Jets ........................................................................................................
32
JET MENUS
• Geneva ...................................................................................................... 33
• Niagara ......................................................................................................34
• Tahitian ........................................................................................................35
• Elation ........................................................................................................36
• Aspire ..........................................................................................................37
• Moorea ......................................................................................................38
• Hawaiian ......................................................................................................39
• Martinique....................................................................................................40
• Kauai ..........................................................................................................41
• Olympia........................................................................................................42
• Cumberland and Aventine..........................................................................43
OPERATING INSTRUCTIONS
• Control Panels - Utopia/Aquatic Melodies/Paradise .............................. 44
• Locking Features ........................................................................................ 44
• Main Control Panel Buttons and Display.................................................. 45
• Auxiliary Control Panel Buttons..................................................................46
• Aquatic Melodies®Surround Sound System............................................47
• Control Panels - Olympia, Cumberland, and Aventine ..........................
48
EQUIPMENT COMPARTMENTS
• Jet Pump Side ............................................................................................51
• Controls Side ..............................................................................................52
MAINTENANCE
• Filter Maintenance ...................................................................................... 52
• Filter Cartridge Removal and Cleaning Instructions ................................ 52
• Diverter Valve Maintenance ...................................................................... 53
• VersaSsage®and Orbissage®Jets Maintenance .................................... 54
• Draining Your Spa ...................................................................................... 54
• Winterizing Your Spa .................................................................................. 55
• Care of the Spa Pillows.............................................................................. 55
• Care of the Exterior .................................................................................... 56
• Care of the Spa Cover .............................................................................. 56
WATER QUALITY AND MAINTENANCE
• Water Terminology...................................................................................... 57
• General Information.................................................................................... 57
• Methods for Testing the Spa Water .......................................................... 58
• The Watkins Spa Water Maintenance Program ...................................... 58
• SPA FROG®Water Care System .............................................................. 60
• Bromine ...................................................................................................... 61
• Monarch®Ozone System .......................................................................... 62
• Common Water Chemistry Questions ...................................................... 64
• Spa Water Maintenance Troubleshooting Guide...................................... 65
SERVICE
• Miscellaneous Service Information............................................................ 66
• Acts Invalidating Warranty ........................................................................ 66
• Disclaimers.................................................................................................. 66
• Watkins Customer Service ........................................................................ 66
SPA TROUBLESHOOTING .............................................. 67
SPA SPECIFICATIONS.................................Back Cover

1
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
AVOIDING THE RISK TO CHILDREN
DANGER:
•RISK OF CHILD DROWNING. Extreme caution must be exercised to prevent unauthorized access by children. To avoid accidents, ensure that children cannot
use a spa unless they are supervised at all times.
WARNING:
• To reduce the risk of injury, do not permit children to use this spa unless they are closely supervised at all times.
• To reduce the risk of injury, lower water temperatures are recommended for young children. Children are especially sensitive to hot water.
DO:
• Make sure you always lock the child resistant locks after using the spa for your children’s safety. Every Caldera spa is equipped with a locking cover that meets
the ASTM F1346-91 Standard for Safety Covers.
• Test the water temperature with your hand before allowing children to enter the spa to be sure that it’s comfortable. Children are especially sensitive to hot water.
• Remind children that wet surfaces can be very slippery. Make sure that children are careful when entering, or exiting the spa.
DON’T:
• Allow children to climb onto the spa cover.
• Allow children to have unsupervised access to the spa.
AVOIDING THE RISK OF ELECTROCUTION
Risk of electrocution
• Connect only to a grounded source. The spa must be connected to a Ground Fault Circuit Interrupter (GFCI). Watkins Manufacturing Corporation does not
supply a GFCI with the spa. Watkins recommends the GFCI be attached to the end of the spa’s electrical cord. The GFCI must be installed by a licensed,
qualified electrican. GFCI devices must meet or exceed all national and local electrical codes.
• Do not bury the power cord. A buried power cord may result in death, or serious personal injury due to electrocution if direct burial-type cable is not used, or if
improper digging occurs.
• A ground terminal (pressure wire connector) is provided on the surface of the control box inside the equipment compartment. This connector should be bonded
with a minimum 6 mm2(10 AWG) solid copper wire between this unit and any metal ladders, metal water pipes, metal enclosures of electrical equipment,
conduit or metal equipment within 1.5 m of the spa. If the spa is located on a reinforced concrete pad, the reinforced steel should also be bonded to the ground
terminal.
WARNING:
• To reduce the risk of electrical shock, replace a damaged cord immediately. Failure to do so may result in death or serious personal injury due to electrocution.
• Always test the Ground Fault Circuit Interrupter (GFCI) before each use of the spa. If the GFCI does not perform properly, a ground current is flowing indication
the possibility of electric shock. Disconnect power to the spa until the fault has been identified and corrected.
NOTE: Failure to wait 30 seconds before resetting the GFCI may cause the spa’s Power Indicator (on the control panel) to blink. If this occurs, repeat the GFCI
test procedure.
• Install the spa so proper drainage is provided for the compartment containing the electrical components.
DANGER: RISK OF ELECTRICAL SHOCK
• Install spa at least 1.5 m from all metal surfaces. A spa may be installed within 1.5 m of a metal surface if each metal surface is permanently connected by a
minimum 6mm2(10 AWG) solid copper conductor attached to the wire ground connector on the terminal box that is provided for this purpose.
• Do not permit any electrical appliances, such as a light, telephone, radio, or television within 1.5 m of a spa. Failure to maintain a safe distance may result in
death, or serious personal injury due to electrocution, if the appliance should fall into the spa.
• Install your spa in such a way that drainage is away from the electrical compartment and from all electrical components.
DO:
• Be sure your spa is connected to the power supply correctly - use a licensed electrical contractor.
• Disconnect the spa from the power supply before draining the spa or servicing the electrical components.
• Test the Ground Fault Circuit Interrupter(s) before each use.
DON’T:
• Use the spa with the equipment compartment door removed.
• Place electrical appliances within 1.5m of the spa.
SAFETY INSTRUCTIONS

2
• Use an extension cord to connect the spa to its power source. The cord may not be properly grounded and the connection is a shock hazard. An extension
cord may cause a voltage drop, which will cause overheating of the jet pump motor and motor damage.
• Attempt to open the electrical control box. There are no user serviceable parts inside.
RISKS TO AVOID
DANGER: RISK OF INJURY
• To reduce the risk of injury to persons, DO NOT remove floating weir, basket and filter located in the filter compartment while the spa is running.
• Never replace a suction fitting with one rated less than the flow rate marked on the original suction fitting.
• There is a danger of slipping and falling. Remember that wet surfaces can be very slippery. Take care when entering or exiting the spa.
• Never operate spa if the suction fittings are broken or missing.
• People with infectious diseases should not use the spa.
• Keep any loose articles of clothing or hanging jewelry away from rotating jets or other moving components.
Increased side effects of medication
• The use of drugs, alcohol or medication before or during spa use may lead to unconsciousness with the possibility of drowning.
• Persons using medications should consult a physician before using a spa; some medication may cause a user to become drowsy, while other medication may
affect heart rate, blood pressure, and circulation.
• Persons taking medications which induce drowsiness, such as tranquilizers, antihistamines, or anticoagulants should not use the spa.
Health problems affected by spa use
• Pregnant women should consult a physician before using spa.
• Persons suffering from obesity, or with a medical history of heart disease, low or high blood pressure, circulatory system problems, or diabetes should consult a
physician before using spa.
Unclean water
• Keep the water clean and sanitized with correct chemical care. The recommended levels for your Caldera spa are:
Bromine: 1.0-2.0 ppm
Water pH: 7.2-7.8
Total Alkalinity: 80-180 ppm
Calcium Hardness: 150-400 ppm
(Refer to Water Quality and Maintenance section for complete instructions.)
IMPORTANT: Turn on the clean cycle when adding ANY spa water chemicals into or in front of the filter compartment.
• Clean the filter cartridge at least monthly to remove debris and mineral buildup which may affect the performance of the hydromassage jets, limit the flow, or trip
the high limit thermostat, which will turn off the entire spa.
AVOIDING THE RISK OF HYPERTHERMIA
Prolonged immersion in hot water can result in HYPERTHERMIA, a dangerous condition which occurs when the internal temperature of the body reaches a level above
normal (37°C). The symptoms of hyperthermia include unawareness of impending hazard, failure to perceive heat, failure to recognize the need to exit the spa, physical
inability to exit the spa, fetal damage in pregnant women, and unconsciousness resulting in a danger of drowning.
WARNING:
The use of alcohol, drugs, or medication can greatly increase the risk of fatal hyperthermia in hot tubs and spas.
TO REDUCE THE RISK OF INJURY:
• The water in the spa should never exceed 40°C. Water temperatures between 38°C and 40°C are considered safe for a healthy adult. Lower water temperatures
are recommended for extended use (exceeding ten minutes) and for young children. Extended use can cause hyperthermia.
• Pregnant or possibly pregnant women should limit spa water temperatures to 38°C. Failure to do so may result in permanent injury to your baby.
• Do not use spa immediately following strenuous exercise.
AVOIDING THE RISK OF SKIN BURNS:
• To reduce the risk of injury, before entering a spa the user should measure the water temperature with an accurate thermometer, since the tolerance of
temperature-regulating devices may vary by as much as ±2°C.
• Test the water with your hand before entering the spa to be sure it’s comfortable.
SAFETY SIGN
Each Caldera®spa is shipped with a SAFETY SIGN in the owner’s package. The sign, which is required as a condition of Product Listing, should be permanently
installed where it is visible to the users of the spa. To obtain additional SAFETY SIGNS, contact your Caldera dealer and request Part #33869.
SAFETY INSTRUCTIONS

IMPORTANT SPA INSTRUCTIONS
The following contains important spa information, and we strongly encourage you to read and apply them.
DO:
• Use and lock the cover when the spa is not in use, whether it is empty or full.
• Follow the Spa Care and Maintenance recommendations stated in this manual.
• Use only approved accessories and recommended spa chemicals and cleaners.
DON’T:
• Leave the Caldera spa exposed to the sun without water or the cover in place. Exposure to direct sunlight can cause solar distress of the shell material.
• Roll or slide the spa on its side. This will damage the siding.
• Lift or drag the vinyl cover by using the cover lock straps; always lift or carry the cover by using the handles.
• Attempt to open the electrical control box. There are no user serviceable parts inside. Opening of the control box by the spa owner will void the warranty. If you
have an operational problem, carefully go through the steps outlined in the Troubleshooting section. If you are not able to resolve the problem, contact your
authorized Caldera dealer. Many problems can easily be diagnosed over the telephone by an Authorized Service Technician.
SITE SELECTION AND PREPARATION
You probably have a spot picked out for your new spa, whether it’s indoors or outdoors, on a patio or on a deck. Just make sure you check the following:
• Always put your spa on a structurally sound, level surface. A filled spa is very heavy. Make certain that the location you choose can support the weight of your
filled spa.
• Don’t forget to level your spa before filling it. (See the Spa Leveling Preparation section of this manual.)
• Locate your equipment compartment, which houses all of the electrical components, in a place where water will drain away from it. Allowing water into the
equipment compartment can damage the electronics, or may result in tripping your house’s circuit breaker.
• Leave access to the equipment compartment for periodic spa care and maintenance.
• Never let water get into the subpanel. Your 230 volt spa’s subpanel is raintight when installed correctly with the door closed.
• Leave access to the entire front of the spa (the removable panel provides access to the spa’s equipment) for periodic spa care and maintenance.
• Note that on the Utopia and Aquatic Melodies®Series spas, the SpaGlo®exterior lighting fixtures are located on only three sides. The side opposite the main
control panel has no lighting.
WARNING: Damage to the spa’s equipment compartment components or internal plumbing as a result of rodent infestation is NOT covered under your
warranty!
OUTDOOR AND PATIO INSTALLATION
No matter where you install your new spa, it’s important that you have a solid foundation to support it. Structural damage to the
spa, resulting from incorrect installation, or placement on an inadequate foundation, is not covered under the spa’s limited warranty.
If you install the spa outdoors, we recommend a reinforced concrete pad at least ten centimeters thick. The reinforcing rod or mesh in the
pad should be attached to a bond wire.
DECK INSTALLATION
To be certain your deck can support your spa, you must know the deck’s maximum load capacity. Consult a qualified building
contractor or structural engineer. To find the weight of your spa, its contents and occupants, refer to the Spa Specification chart on
back page. This weight per square foot must not exceed the structure’s rated capacity, or serious structural damage could result.
INDOOR/BASEMENT INSTALLATION
Be aware of some special requirements if you place your spa indoors. Water will accumulate around the spa, so flooring materials
must provide a good grip when wet. Proper drainage is essential to prevent a build-up of water around the spa. When building a new
room for the spa it is recommended that a floor drain be installed. The humidity will naturally increase with the spa indoors. Water may
get into woodwork and produce dry rot, mildew, or other problems. Check for airborne moisture’s effects on exposed wood, paper,
etc. in the room. To minimize these effects, it is best to provide plenty of ventilation to the spa area. An architect can help to determine
if more ventilation must be installed.
Caldera spas are equipped with a jet pump shroud to remove excessive heat from the equipment compartment. Find this vent and be
sure the vent is not blocked by anything, including carpeting.
Watkins Manufacturing
Corporation recommends
that the Caldera spa be
installed above ground.
Lowering the top of the spa
to ground level, or
employing decking which
raises standing level toward
the top of the spa
substantially increases the
hazard of accidental entry.
Consult a licensed building
contractor to design or
evaluate your custom
decking requirements.
3
SAFETY INSTRUCTIONS
INSTALLATION

4
Your Caldera dealer can help you with local information such as zoning regulations and building codes.
WARNING: Please keep the area around your spa well ventilated when it is installed indoors or in a confined area. Inadequate ventilation around the spa could
cause a build-up of a higher-than-normal concentration of spa chemicals and/or bacterial fragments. These dispersed spa chemicals and/or bacterial fragments can be
inhaled, and may result in breathing difficulties or lung damage in certain people suffering from a compromised immune system or respiratory infection. If you or other
bathers are affected by this condition, please seek medical attention as soon as possible.
In addition to the above, properly clean and maintain your spa as follows:
• Follow all procedures in this owner’s manual and printed instructions on all water care (chemical) products packaging.
• Test the water regularly to ensure proper levels of sanitizers, pH, and other water care requirements.
• Drain, clean, and refill your spa with fresh water on a regular schedule, and in accordance with this owner’s manual.
• Clean the filter(s) at least once per month.
• Check to make sure you have proper circulation throughout your spa water system.
• Have spa users bathe before entering the spa water.
GROUND AND SPA LEVELING PREPARATION
Your Caldera spa has been engineered to perform on several types of common yard surfaces.
While a concrete slab is best for long-term use*, other foundations are acceptable as long as a
level base is prepared prior to delivery. Three foundation base pictures, shown at right, represent
examples of alternatives to a concrete slab for spas installed without gazebos or other accessories.
*NOTE: A reinforced concrete pad at least four inches thick or structurally sound deck able to
support the “dead weight” found in the spa specification chart is required for the Geneva™,
Niagara®, Elation®and Moorea™spas, and recommended for the Aspire®, Tahitian®, Hawaiian,
Martinique®, Kauai®, and all Highland spas. The reinforcing rod or mesh in the pad should be
attached to a bond wire.
INSTALLATION NOTES:
• Concrete sloped at 1.3 centimeters per 3 meters is preferred so that rain water and water
spillover will run off and not puddle underneath the spa (water under the spa for long periods
of time may cause the wood to deteriorate).
• If stepping stones or railroad ties are selected for the spa foundation, they should be placed
and leveled below the entire spa to maintain even distribution of the spa weight.
• It is important to note that soft surfaces, even when stepping stones are used to distribute
the weight of the spa as evenly as possible, will still have a tendency to settle unevenly, resulting in an unlevel spa.
NOTE: Placing the spa on grass or dirt may increase the amount of debris which is inadvertently brought into the spa water and may cause harm to your equipment as
well as the spa surface, which is not covered under warranty.
DELIVERY ACCESS
NOTE: It may be necessary to allow for additional over-head clearance if the spa will be rolled up or down an incline or
moved up or down a short flight of stairs.
Use the information in the chart on the next page to determine the requirements for access to your desired location. It may
be necessary to remove a gate, part of a fence, or other movable obstructions in order to roll the spa to its installation site.
About ten percent of the time, a crane is the only way to install the spa by lifting it to its final destination.
If the spa has to be taken off of the cart to go over a wall (either because the entry area is too narrow, the eaves are too low,
the corner is too tight, or the stairway is too steep), a crane will be required. Don’t be alarmed!
The crane has a truck-mounted boom which can fit right in your driveway. It is run by a licensed and insured operator. For a
charge, the crane operator will lift your spa over walls, buildings, or any other obstruction and place it as close to the
installation site as possible. The Caldera spa delivery personnel will supervise the crane delivery and complete the spa
installation Crane delivery typically takes an average of 30 minutes to complete. Crane delivery typically takes an average
of 30 minutes to complete.
NOTE: If your spa delivery requires the use of a crane, you may be required to pay for its services at the completion of the
delivery.
INSTALLATION
Slope 1.3 cm (1/2 inch) per 305 cm (10 ft.)
for proper drainage.
1.3 cm
(1/2 inch)
3 m (10 ft.)
Stepping stones or brick may settle
causing the spa to be unlevel.
WARNING
LEVEL
RAILROAD TIES
PRE-CAST
STEPPING STONES
PEA GRAVEL
OR CRUSHED ROCK
FOUNDATIONS FOR SPAS ONLY
(No gazebo)
CONCRETE PADS
BRICK SURFACES
WOOD DECKING
FOUNDATIONS FOR SPAS
WITH GAZEBOS

5
SPA COVER INSTALLATION
• Place the cover squarely on the spa.
• Position the tie-down locks included with your cover on the side of the spa so that they are easily reached by the cover tie-down straps. Allow for about 1.5 cm
to 2 cm of slack in the straps to make it easy to insert straps into locks and to compensate for vinyl shrinkage in cold weather.
• Attach the locks with the screws provided and insert the cover tie-down straps into the locks.
NOTE: Keeping the cover in place any time the spa is not in use will reduce the amount of time the heater operates, thereby minimizing operating costs.
COVER INSTALLATION
TIE-DOWN STRAP
LOCK
COVER
KEY
SCREW (2)
DANGER. RISK OF INJURY.
• Never leave a spa uncovered or unattended.
• Never leave a spa cover unlocked.
• Do not stand, sit, or lie on the cover.
Model Height H Length L Width W
Geneva™97 cm 226 cm 226 cm
Niagara®97 cm 226 cm 226 cm
Tahitian®91 cm 213 cm 213 cm
Elation®97 cm 231 cm 231 cm
Aspire®91 cm 213 cm 213 cm
Moorea®91 cm 231 cm 213 cm
Hawaiian 91 cm 213 cm 213 cm
Martinique®86 cm 226 cm 193 cm
Kauai®74 cm 213 cm 165 cm
Olympia 91 cm 212 cm 213 cm
Cumberland®91 cm 198 cm 198 cm
Aventine®74 cm 173 cm 173 cm
How isyour width and height clearance?
Protruding electric meters
A/C units
Do you have sufficient
overhead clearance?
Check low roof eaves,
overhanging branches,
rain gutters
Isthe path clear?
Move away branches, dog
houses, firewood, etc.
If there isa90 turn, can we
clear it? (The spawill not bend.)
No more than 6 consecutive
stairswithout alanding
to accommodate the spa
Gas meters
Check all gates
HOUSE
BACK YARD
STREET
SPA DIMENSIONS
INSTALLATION

6
85"
Air VentAir Vent
UPSIDE DOWN VIEW OF SPA WITHOUT THE BASE PAN
Pedestal
85”(215cm)
Pedestal
Overall
89"
Overalll
89”(226cm)
Electrical Cutout Electrical Cutout
Air Vent
35”
38”
1.5”
28.125”(71.4cm)
DOOR
21.25”(53.9cm) 26.625” (67.6cm)
DOOR DOOR
AIR VENTS
ELECTRICAL
CUTOUT
5.5”(13.9cm)
DO NOT BLOCK
SPA DRAIN
5.0”
FRONT
VIEW
BOTTOM
VIEW
DOOR SIDE
4.0”(10.2cm)
12.7cm 3.8cm
88.9cm
91.4cm
(226cm)
(215cm)
4.0”(10.2cm)
NOTE: Watkins Manufacturing Corporation requires that the Geneva and Niagara be installed on a minimum 10.2 cm thick reinforced concrete pad or structurally sound
deck able to support the “dead weight” found in the spa specification chart.
WARNING: The Geneva and Niagara must not be shimmed in any manner.
GENEVA
TM AND NIAGARA®
NOTE: All dimensions are approximate; measure your spa before making critical design or pathway decisions.
DIMENSIONS

7
NOTE: Watkins Manufacturing Corporation recommends that the Tahitian, Aspire, and Hawaiian be installed on a minimum 10.2 cm thick reinforced concrete pad or
structurally sound deck able to support the “dead weight” found in the spa specification chart.
WARNING: The Tahitian , Aspire and Hawaiian must not be shimmed in any manner.
TAHITIAN
®,
ASPIRE
®,
AND HAWAIIAN
NOTE: All dimensions are approximate; measure your spa before making critical design or pathway decisions.
DIMENSIONS

8
NOTE: Watkins Manufacturing Corporation requires that the Elation be installed on a minimum 10.2 cm thick reinforced concrete pad or structurally sound deck able to
support the “dead weight” found in the spa specification chart.
WARNING: The Elation must not be shimmed in any manner.
ELATION
®
NOTE: All dimensions are approximate; measure your spa before making critical design or pathway decisions.
DIMENSIONS

9
NOTE: Watkins Manufacturing Corporation requires that the Moorea be installed on a minimum 10.2 cm thick reinforced concrete pad or structurally sound deck able to
support the “dead weight” found in the spa specification chart.
WARNING: The Moorea must not be shimmed in any manner.
MOOREA
®
NOTE: All dimensions are approximate; measure your spa before making critical design or pathway decisions.
DIMENSIONS

10
NOTE: Watkins Manufacturing Corporation recommends that the Martinique be installed on a minimum 10.2 cm thick reinforced concrete pad or structurally sound deck
able to support the “dead weight” found in the spa specification chart.
WARNING: The Martinique must not be shimmed in any manner.
MARTINIQUE
®
NOTE: All dimensions are approximate; measure your spa before making critical design or pathway decisions.
DIMENSIONS

11
NOTE: Watkins Manufacturing Corporation recommends that the Kauai be installed on a minimum 10.2 cm thick reinforced concrete pad or structurally sound deck able
to support the “dead weight” found in the spa specification chart.
WARNING: The Kauai must not be shimmed in any manner.
KAUAI
®
NOTE: All dimensions are approximate; measure your spa before making critical design or pathway decisions.
DIMENSIONS

12
Electrical
Cutout
Air Vent Air Vent
Electrical
Cutout
BOTTOM
VIEW
Pedestal
Overalll
80”
84”
Pedestal
80"
Overall
84"
DOOR SIDE
4.0”(11cm)
ELECTRICAL
CUTOUT
5.5”(14cm)
1.5”(4cm)
36”(92cm)
33”(84cm)
SPA DRAIN
DOOR
21.75” 5.5”
ELECTRICAL
CUTOUT
AIR VENTS
DO NOT BLOCK
DOOR
29.875”
DOOR
20.625”
LOCATED
BEHIND DOOR
FRONT
VIEW
(14cm)
(52cm)
(75cm)
(75cm)
(213cm)
(203cm)
(203cm)
(213cm)
4.0”(11cm)
NOTE: Watkins Manufacturing Corporation requires that the Moorea be installed on a minimum 10.2 cm thick reinforced concrete pad or structurally sound deck able to
support the “dead weight” found in the spa specification chart.
WARNING: The Olympia must not be shimmed in any manner.
OLYMPIA
NOTE: All dimensions are approximate; measure your spa before making critical design or pathway decisions.
DIMENSIONS

13
ELECTRICAL
CUTOUT
5.5”(14cm)
Pedestal
74"
Overall
78"
78”
Pedestal
74”
Overall
Electrical
Cutout
Cutout
Electrical
Air Vent
Air Vent
47.57"
30.64"
47.57"
BOTTOM
VIEW
6.5”
1.5”(4cm)
36”(91cm)
33”(84cm)
52.57” 30.64"
DOOR
DOOR SIDE
ELECTRICAL
CUTOUT
SPA DRAIN
BEHIND DOOR
LOCATED
FRONT
VIEW
6.5”
6.5”(16cm)
(133cm)
(17cm)
(78cm)
(199cm)
(188cm)
(199cm)
(188cm)
(120cm)
(78cm)
(16cm)
(121 cm)
NOTE: Watkins Manufacturing Corporation requires that the Moorea be installed on a minimum 10.2 cm thick reinforced concrete pad or structurally sound deck able to
support the “dead weight” found in the spa specification chart.
WARNING: The Cumberland must not be shimmed in any manner.
CUMBERLAND
®
NOTE: All dimensions are approximate; measure your spa before making critical design or pathway decisions.
DIMENSIONS

14
NOTE: Watkins Manufacturing Corporation requires that the Moorea be installed on a minimum 10.2 cm thick reinforced concrete pad or structurally sound deck able to
support the “dead weight” found in the spa specification chart.
WARNING: The Aventine must not be shimmed in any manner.
AVENTINE
®
NOTE: All dimensions are approximate; measure your spa before making critical design or pathway decisions.
DIMENSIONS

OVERHEAD VIEW
15
CONTROLS AND EQUIPMENT
1. Air Control
2. Euro-Pulse
®
Jet
3. Euro Directional Jet
4. Air Jet
5. AdaptaFlo
TM-
Jet
6. AdaptaSsage
TM
Jet
7. VersaSsage
®
Jet
8. OrbiSsage
®
Jet
9. Whirlpool Jet
10. Euphoria
®
Jet
11. Diverter Valve
12. Drain
13. Light
14. Ozone Jet
15. Control Panel
16. Pillow
17. Filter Compartment
18. Auxiliary Panel
19. Assist Bar
20. Atlas
®
Neck Jet Valve
21. Atlas Neck Jet Pillow
22. Temperature Sensor
23. Waterfall Valve
24. Acquarella
®
Waterfall
25. SPA FROG
®
1
1
1
1
34
4
44
4
6
5
7
7
11 18
12
12
12
13
14
15
22
16
19
16
21
20
17
1
2
2
3
3
44
25
8
3
3
33
4
GENEVA
TM
11
11
23
24
9
3
3
10

16
20
19
17 15
14
15
18
15
16
14
11
24
12
13
1
1
1
1
9
11
2
2
3
3
3
3
3
3
3
4
4
4
4
4
4
6
6
6
5
7
CONTROLS AND EQUIPMENT
1. Air Control Valve
2. Euro-Pulse
®
Jet
3. Euro Directional Jet
4. Air Jet
5. AdaptaFlo
TM
Jet
6. VersaSsage
®
Jet
7. OrbiSsage
®
Jet
8. Whirlpool Jet
9. Euphoria
®
Jet
10. Diverter Valve
11. Drain
12. Light
13. Ozone Jet
14. Control Panel
15. Pillow
16. Filter Compartment
17. Auxiliary Panel
18. Assist Bar
19. Atlas
®
Neck Jet
Valve
20. Atlas Neck Jet Pillow
21. Temperature Sensor
22. Waterfall Valve
23. Acquarella
®
Waterfall
24. SPA FROG
®
OVERHEAD VIEW
NIAGARA
10
10
10
21
22
23
4
11
8

17
CONTROLS AND EQUIPMENT
1. Air Control Valve
2. Temperature Sensor
3. Euro Directional Jet
4. Air Jet
5. AdaptaSsage
TM
Jet
6. AdaptaFlo
TM
Jet
7. VersaSsage
®
Jet
8. OrbiSsage
®
Jet
9. Euphoria
®
Jet
10. Whirlpool Jet
11. Diverter Valve
12. Drain
13. Light
14. Ozone Jet
15. Control Panel
16. Pillow
17. Filter Compartment
18. Auxiliary Panel
19. Assist Bar
20. Waterfall Valve
21. Atlas
®
Neck Jet
Valve
22. Atlas Neck Jet Pillow
23. Acquarella
®
Waterfall
24. SPA FROG
®
1
11
3
3
3
3
4
4
4
4
4
5
6
7
7
9
10
12
12
12
13
15
19
16
16
22
18
17
1
3
4
4
4
3
3
OVERHEAD VIEW
TAHITIAN®
14
1
11
11
11
2
20
21
23
8
24
1