Caliber RampPro HD 13528 User manual

CALIBER®
952-985-9999 Assembled on 8 June 2020
www.caliberproductsinc.com G:\Shipping&ReceivingDepartment\CaliberInstructions\13528-CI5073-RampPro
HD.docx
CALIBER RampPro HDTM
Assembly Instructions for Part No. 13528
Hardware Included:
1 –Retrax Accessory Strap (PN. 13548)
1 –Clevis Pin
Tools Required:
6mm Allen Key
13mm Socket/Wrench
READ ALL INSTRUCTIONS CAREFULLY PRIOR TO ASSEMBLY
-Maximum recommended load surface height: 45
inches
-Maximum loaded vehicle width - complete
ramp: 52 inches
-Rated capacity of complete ramp: 3,000 lbs.
-Rated capacity of each side section: 1,250 lbs.
-Always use safety straps attached to both the transport
vehicle and ramp
-Always use additional safety strap when the ramp
is separated. Additional retractable straps
available (Caliber PN 13548)
-Always load or unload on a solid, level, and stable
surface with the transport vehicle in park, parking
brake on, and engine off
CALIBER, INC. LIMITED LIFETIME WARRANTY
Caliber, Inc. warrants that this product will be free from defects in material or workmanship under normal use, installation and service. Several parts of Sled Wheels are
considered wear items: the wheels, rubber finger covers and extenders, rubber hook plate, and rubber latch cover, and are available for purchase from Caliber dealers. Caliber,
Inc. reserves the right, before having any obligation under this limited warranty, to inspect the damaged Caliber product. All warranty shipping costs for inspection shall be
borne solely by the purchaser. This limited warranty is non-transferable. Contact Caliber, Inc. at www.caliberproductsinc.com/warranty or at 952-985-9999 for warranty service
procedures.
DISCLAIMER
Caliber, Inc. shall not be liable for any special, incidental or consequential damages, including, but not limited to, lost revenues, lost profits, personal injury, damage to
property, and third-party claims, arising out of any warranty, contract, statutory or tort. Notwithstanding the term of any limited warranty or any warranty implied by law. In
the event that any limited warranty fails of its essential purpose, in no event will Caliber’s entire liability exceed the purchase price of this product
Step 1:
-Remove Retrax accessory strap from top rung of ramp.
Step 2:
-Install Retrax accessory strap with the nut/bolt fixed to
the top run of the ramp –using a 6mm Allen and 13mm
wrench.
-Use elongated slot fixed in the center of the ramp to clip
the 2” hook for storage.
Step 3:
-Place ramp on vehicle and remove clevis pin for use. Ensure Retrax strap is attached to the receiver and secured.
To use with Full-Size UTVs, Snow bikes, Dirt bikes, and Motorcycles see next page.

CALIBER®
952-985-9999 Assembled on 8 June 2020
www.caliberproductsinc.com G:\Shipping&ReceivingDepartment\CaliberInstructions\13528-CI5073-RampPro
HD.docx
Full-Size UTV:
Step 1:
-Remove all six (6) bolts from outer portions
of the ramp and put them back into the
center section for storage purposes.
Step 2:
-Attach additional accessory strap required
for split-ramp use (P/N 13548 - $19.95).
Step 3:
-Remove strap from center
section of the ramp and attach
to secondary outer portion.
Purchasing two accessory straps
for both outer portions is also
an option to keep all straps in
place.
Step 4:
-Place ramps on trailer and ensure Retrax straps are securely fastened to the trailer prior to loading vehicle
(Outer portions have 1,250lb. capacity each).
Snowbike –Dirtbike –
Motorcycle:
Step 1:
-Remove all six (6) bolts from outer portions
of the ramp and put three (3) back into the
center section for storage purposes
Step 2:
-Remove strap from center
section of the ramp and attach
to secondary outer portion, or
use an additional accessory
strap (P/N 13548 - $19.95)
Step 3:
-Place ramp on vehicle and ensure Retrax strap is securely fastened to the vehicle prior to loading vehicle (Outer
portions have 1,250lb. capacity each.

CALIBER®
952-985-9999
Assembled on 8 June 2020
www.caliberproductsinc.com G:\Shipping&ReceivingDepartment\Caliber
Instructions\13528-CI5073-RampProHD.docx