CallingSYS RW6 User manual

WATCH WIRELESS
CALLING RECEIVER
USER MANUAL
2017-07-15 Mon

Watch wireless calling receiver
I Preface
Thanks for using callingsys watch receiver, it adopts wireless
technology, digital identify, TFT screen and high stable IC together to
realize time display and wireless calling. The watch uses rechargeable
battery and safe charging circuit.
The watch receiver is widely used in restaurants, bars, cafes,
hospitals, hotels, and factories and so on.
II Feature
TFT colorful screen
RF wireless technology
Fashionable watch design
Fully waterproof
Up to 999 channels
Call button data pin support for custom
Call button words selectable
Single or list display mode
Accurate time display
Vibration/Buzzer prompt
Low-power indication
Built-in rechargeable battery
1

III Technical Data
1) Working voltage: DC3.7V rechargeable Li-poly battery
2) Working frequency: 433.92MHz
3) Working current: 57mA±10mA (buzzer mode)
95mA±10mA (vibration mode)
4) Standby current: <8mA
5) Power-off current: 180±5μA
6) Receiving sensitivity: -108dBm
7) Decoding: learning code
8) Modulation: AM
IV Diagram
1. Diagram of function
2
2017-07-15 Mon
Power capacity
Date&Time
Charging indicator
Up
Down/Power on/off
Prompt mode
SET/OK
Return(Hold on)

Press the button 3s to enter settings;
In pairing setting, press the button to change the cursor position;
In deleting setting, press the button to delete one paired call button.
In calling status, press the button to delete one calling record.
Hold on for return, back to previous menu
In pairing/deleting settings, press UP/DOWN to select the number
from 0 ~ 9, A ~ Z, - * # .
in calling status, press the button to browse the calling records.
Press the button 3s to power ON/OFF the receiver;
Press the button 3s to switch on/off the receiver module;
Note: in standby status, press any button to wake up the screen.
2. Diagram of display
Note: the software may be updated, in different versions, the
interface may be little different.
3
16:20
0009
0008
0123
08call
order
satisf.
03
01
call times 16:15
16:14
16:13
01/05
15
16:20 01/05
Order 16:15 calltime
call number
callfunction
call num.
calltime
callfunction
clock call records call records
Single display mode
List display mode
clock

Button define
Define call button pin function
Button word
Each button displayed word can be changed
Advanced mode
If off, only work 1/2/3/4-button call buttons
Brightness
Screen brightness 1~25
Prompt time
OSC resistor
AntiMaliceCall
Auto off time
Vibration or buzzer prompt time 1~10s
Optional for 200-400us/400-700us
Very quick press call button ignored
Screen auto off time 1~180s
General mode
Digits + letter mode, like A1b3
999 mode
Multi-ID mode
No. 1~999 only
Each button can be paired as a number.
List del mode
All paired call buttons list our for deleting
Search del mode
Press some one call button and delete
Del all buttons
Delete all call buttons
Vibration
Vibration only
Buzzer
Buzzer only
Vibration&buzz
Mute
Vibration&Buzzer prompt
No prompt
Single
Each screen only shows one calling record
List
Each screen can show 3 records in list
List all
For order mode
Ascend
The lastest one calling record is oldest
Descend
The lastest one calling record is newest
7Auto clear time 000
Calling records can be cleared automatically
English
English version
…
Other language
16:00
Time
16-01-08 Fri
Date and week
Return
Back to previous menu
Restore part
Restore to default except pairing data
Restore all
All will be restored to default
9
10
Display mode5
Language
Date&Time
Restore
default
1
2
3
4
6
8
General
Pair buttons
Delete buttons
Prompt mode
Display order
3. Diagram of settings menu
4

V Using method
1. Wear the watch receiver to the wrist, and put the call buttons in
suitable place.
2. Press " " 1s button to power on.
3. Pair the call buttons with the watch receiver. (refer to below
instruction)
4. When need calling service, press the call buttons, the watch
receiver will receive the signal, and display number on the screen
with vibration or buzzer prompt.
If customer pressed wrong or no need just called service, press
“Cancel” button to cancel the calling service. The calling record
will be deleted from the calling records list on the screen.
Note: before calling service, the transmitter should be paired to the
receiver according its numbers.
VI Settings
Power on the watch receiver, then the screen turns on and displays
the date and time, as well as other information. In standby status,
press “SET” button 3 sec to enter settings. The main settings are:
5
Settings
Delete buttons
1/10
General
Prompt mode
Pair buttons
Settings
Auto clear time
Language
Display Order
Date&Time
8/10

1.General
In general settings, set the basic function of the watch receiver. Each
call button has one ID number, on the call buttons, there are one or
more press buttons, each button has different data pins as below:
1) Button define: this function can change the call button data pins.
Normally no need change it, if it is changed in error, please restore
to factory default.
2) Button word: when press the call buttons, the corresponding
word will be showed on the watch, like “Call”, “Order”, “Pay”...as
default, but the word can be changed for different occasions. For
example, select item A, press [SET] button, there is words list,
select one which you want to show.
3) Advanced mode: if not open advanced mode, the watch receiver
only receive the D0/D1/D2/D3 data.
4) Brightness: set screen brightness 1 to 25.
5) Prompt time: set vibration or buzzer time from 1 to 10s.
6) OSC resistor: support 200-400us and 400-700us call buttons.
7) Anti-Malious Call: when call button is pressed very quickly, it only
recognize one time.
8) Auto off time: Screen auto off time from 1 to 180s.
2. Pair buttons
1) Pairing call button
6
Data pin D0 D1 D2 D3 D0+D1 D0+D2 … D0+D1+D2+D3
Items A B C Cenc D E … N
Default Order Call Pay Cancel Satisfied Dissatisfied … Check

In pairing settings, there are 3 pairing mode, “General mode”, “999
mode” and “Multi-ID mode”.
a) In “General mode”, there are 4 digital position, each position can
be select from “0~9, A~Z, - * # ” characters. You can set any
words or letter+digit, like 0001, 56-9, RM33, HELP, A1B2 etc.
Press [SET] button to select the position, then press [UP/DOWN] to
adjust the value to select a ID number, then press any button on the
call button (transmitter), the watch will receive the wireless signal
and record it on this number, the status will turn to “Paired” and
jumps to next number automatically.
b) If no need complicated using environment, please select “999
mode” which ID is number only, from 1 to 999.
c) In multi-ID mode, each button on the transmitter can be paired as
a call button.
3. Delete buttons
There are 3 ways to delete paired call buttons:
1) List del button: in this mode, all the paired call buttons are
showed in the list, you can select one by one and press [SET] button
to delete.
7
General mode
Pair
0000
001/999
General mode
Null
0001
001/999

2) Search del button: if there are too many paired call buttons, it is
hard to select one. In this mode, press the call button, it jumps to the
number, then press [SET] button to delete.
3) Del all buttons: in this mode, all the paired button will be deleted.
4. Prompt mode
There are 3 prompt modes when there is calling coming.
1) Vibration
2) Buzzer
3) Vibration & Buzzer
4) Mute
5. Display Mode
The calling records display has 3 modes.
1) Single: on each page, it only displays one record, press
[UP/DOWN] button to browse others.
2) List: all the calling records display in the list, each page displays 3
records. press [UP/DOWN] button to page up/down. If one call
button called many times, only one record and calling times are
showed.
8
16:20
0009
0008
0123
08call
order
satisf.
03
01
16:15
16:14
16:13
01/05
15
16:20 01/05
Order 16:15
Single display mode
List display mode

3) List all: same to “List” function, but if one call button called many
times, all records are showed in the list, not show calling times.
6. Display Order
The calling records display has 2 sequences:
1) Ascend – the latest calling record is shown in the below.
2) Descend – the latest is calling record shown on the top.
Note: the default is descend order.
7. Auto clear Time
The calling record can be cleared automatically from the calling
records list, the time is from 1 to 180s.
Note: the default time is 000, that means no open auto clear function.
8. Language
The watch receiver supports multiple languages, select and press
“BACK” button to quit.
9. Date & Time
Press [SET] button to change the cursor
position, then press [UP/DOWN] button to
adjust the value.
10. Restore default
There are 3 options, select one and press [SET] button to restore.
1) Return– Return to previous menu, nothing changed.
2) Restore part – only system settings are restored to factory default
except pairing information.
3) Restore all – all settings will be restored to factory default
9
16-01-08 Fri
Date & Time
12:00