CAMBRIDGE X36WMEF1SSBR Owner's manual

Installation and Operation Instructions
ELECTRIC FIREPLACE
X36WMEF1SSBR X42WMEF1SSBR
REV18-01

Important Safety Instructions
Listing Approvals
Glass Particles Installation Instructions
2
2-3
5
6
7-8
9-10
12
12
13
13
3-4
Tool list
Assembly Instructions
Operating Instructions
Remote Control Instructions
Temperature Limiting Control
Trouble Shooting
13
Cleaning
Installation
1
Product Dimensions

Tool List: drill bit, drill, tape measure and pencil.
Remote Control Electric Wall-Mount Fireplace
Assembly Instructions
X36WMEF1SSBR X42WMEF1SSBR
Quick Reference Guide
1. Prior to plugging your heater into a power outlet, first verify that the circuit breaker
for the outlet is on.
Suggested tools: Phillip head screw driver, power drill, drill bit, and a tape
measure. Unit needs to be hung on wall stud for more security and stability.
(1) Fireplace assembly 1PC (2) Steel holder
1PC
(3) Remote Control
1 PC
(4) Screw
Care and Cleaning Instructions: Replace the faux fire log set with glass particles:
Remove the glass pane, then replace the faux fire
log set with glass particles.
Before using, wipe with a clean, dry cloth.
Avoid rubbing or scratching the
surface with rough or abrasive objects.
Assembly Tool Required
Phillips Screwdriver
glass particles
2
￠4mm x 10mm 28 PCS
￠4mm x 8mm 4 PCS
￠4mm x 40mm 10 PCS
Expansion pipe 10 PCS

3
2. The heater may emit a slight, harmless odour when first used. This odour is
normal and it is caused by the initial heating of internal heater parts and will not
occur again.
3. If the heater does not emit heat, Consult your User’s Guide for further
information.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN THE UNIT
NO USER-SERVICEABLE PARTS INSIDE
HIGH TEMPERATURE
KEEP ELECTRICAL CORDS, DRAPERY AND OTHER FURNISHINGS AT LEAST 1 METRE FROM
FRONT OF THE HEATER AND KEEP THEM AWAY FROM THE SIDES OF HEATER
WARNING
RISK OF FIRE - KEEP COMBUSTIBLE MATERIAL AWAY FROM TOP OF HEATER.
SERVICING SHOULD BE DONE ONLY WHILE THE HEATER IS UNPLUGGED FROM
POWER SUPPLY.
The flame effect on the wall hanging fireplace is created by LED surface mounted
components that are designed to last the life of the product. Do not remove back cover of
heater, no user serviceable parts are contained within.
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, to reduce the risk of fire, electric shock and injury to persons, basic precautions
should always be followed, including the following:
.
1. Read all instructions before use.
2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided use
handle when moving this heater.
3. Keep combustible materials such as furniture, pillows, bedding, papers, clothes, and curtains at least
4" / 7cm away from the front of heater and keep them away from the sides of heater.
4. Extreme caution is necessary when any heater is used by or near children or invalids and whenever the

4
heater is in operation it must not be left unattended.
5. Always unplug the heater when not in use.
6. Do not operate any heater with damaged cord or plug or after the heater has malfunctioned or has been
dropped or damaged in any manner. Return heater to an authorised service facility for repair.
7. Do not use outdoors.
8. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate
heaters where it may fall into a bath tub or other water container.
9. Do not run cord under carpeting. Do not cover cord with throw rugs, runners or the like. Arrange cord
away from traffic areas and where it will not be tripped over.
10. To disconnect heater, turn control to off, then remove plug from outlet.
11. Connect to properly grounded outlet only.
12. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an
electric shock or fire, or damage the heater.
13. To prevent a possible fire, do not block air intake or exhaust in any manner.
14. Do not use on soft surfaces, like a bed, where openings may become blocked.
15. A heater has hot and arcing or sparkings parts inside. Do not use it in areas where gasoline, paint or
flammable liquids are used or stored.
16. Use this heater only as described in manual. Any other use not recommended by the manufacturer may
cause fire, electric shock, or injury to persons.
17. Avoid the use of an extension cord because the extension cord may overheat and there is a risk of fire.
18. Do not strike the heater glass.
19. Always use properly grounded, it may break fused and polarized outlets.
20. Always disconnect power before perfoming any cleaning or maintenance, or relocation of the heater.
21. When transporting or storing the heater keep in a dry place, free from excessive vibration and store so as
to avoid damage.
22. The flame effect is powered by a motor and it is normal for the motor to make some noise as it slowly
rotates and helps to create the beautiful 3D flame effect. Some rooms have more or less furnishings than
others resulting in varying noise amplification.
23. Whilst every effort is made to ensure packing materials are kept outside of the plastic bag which covers
your heater in the box, there is a remote chance that some packing may lodge itself in the heater part of
the unit. If you notice this on close inspection, please remove it. When turning your heater on for the first
time it is normal for the heater to emit a little ‘new heater’ smell which quickly passes.
24. You may notice some light coming from under or from the sides of the unit. This is normal and the holes
allow the unit to ‘breathe’. Do not attempt to block these holes.
teltuonaniesutonoD.tiucricdednuorg,PMA2.11,V021/011anode
suebotsiretaehsihT.52 controlled
by a switch or dimmer switch. The cord supplied with the heater, has a 2 blade plug, the round pin on
the plug is for grounding purposes. If a 2 slot receptacle is not available, an adapter must be used, and
the adapter must be properly grounded to the outlet box. Avoid plugging other appliances into the same
circuit as heater.

LISTING APPROVALS
This heater has been tested in accordance with the CSA Standards.
Model Number: X36WMEF1SSBR X42WMEF1SSBR
Description: Wall Mount Electric Fireplace
Voltage: 120V AC, 60Hz
Watts: MAX 1300W
Length: 36.0
Height: 23.9
Depth: 9.1
42.0
23.9
9.1
5

GLASS PARTICLES INSTALLATION INSTRUCTIONS
1.To remove the front panel around the bracket, undo the mounting
screws (red arrows)（①、②）
2.Remove the front panel (③)
3.Carefully take out the log set (③)
4.Gently put the glass crystals into place (③)
5.Be cautious about the outer glass bracket screws（④）
ʑ
ʒ
ʏ
ʐ
6
CHANGE THE FRONT PANEL
This item has two interchangeable front panels .
Follow steps 1-3 to change the panel

PRODUCT DIMENSIONS
36" /42"
9.1"
7
23.9"
FRONT VIEW
BOTTOM VIEW

PRODUCT DIMENSIONS
WARNING: Due to high temperatures, this electric fireplace should be located out of traffic. Keep combustible
materials such as furniture, pillows, bedding, papers, clothes and curtains at least 36" from the top of the heater.
WARNING: Never locate this electric fireplace where it may fall into a bathtub or other water container.
CAUTION: Do not expose the electric fireplace to the elements (such as rain, etc)
WARNING: To prevent contact with sagging or loose insulation, the electric fireplace must not be installed
against a vapor barrier or exposed insulation. Localized overheating could occur and a fire could result.
BACK VIEW
Mounting Bar
8

9
UNPACKING AND TESTING FIREPLACE
Carefully remove the unit from the box. Prior to installing the unit, test to make sure the unit operates
properly. To do this, plug the unit's power supply cord into a conveniently located 120 Volt grounded outlet.
INSTALLATION
WARNING: RISK OF FIRE! The power cord must not be pinched or against a sharp edge. Secure cord to avoid
tripping or snagging to reduce risk of fire, electric shock or personal injury. Do not run cord under carpeting. Do
not cover cord with throw rugs, runners or the like. Arrange cord away from traffic area and where it will not be
tripped over.
WARNING: RISK OF FIRE! To prevent a possible fire, do not block air intake or exhaust in any manner. Do not
use on soft surfaces where openings may become blocked.
WARNING: RISK OF FIRE! Do not place insulation against the fireplace.
WARNING: This electric fireplace is tested and listed for use only with the approved optional accessories. Use
of optional accessories not specifically tested for this electric fireplace could void the heater warranty and / or
result in a safety hazard.
WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result
causing property damage, personal injury or death. Do not store or use gasoline or other flammable vapors in the
vicinity of this or any other heater.

10
Fix the front panel and machine together
using 6pcs screws on the right and left side
Insert the front panel to the machine as
the arrow point
Fix the air guide with 3 screws as shown

11
Remove the bracket from the machine
Install the bracket on the wall with 8 screws Hung on the machine to the bracket
Insert the front panel to the machine Fix the front panel and machine together
using 6pcs screws on the right and left side

OPEARTING INSTRUCTIONS
12
LED DISPLAY
1 POWER: I / O
Touch the button once (flame will light up) to turn power on for all functions, keep the last flame color
once appliance off. Touch the button once more to turn all functions off and flame off.
2 FLAME ADJUSTMENT:
Touch the button to turn flame on. There are 7 colors in total . Press this button to change color.
The display will show Orange(A1), Green(A2), Blue(A3), Red(A4), Orange/Blue(A5), Orange / Green / Blue (A6) ,
Circle( A7)
3 HEATER CONTROL:
This fireplace consists of a fan forced electric heater with two heat settings: 600W (“HI” shown in display) and
1300 W (“H2” shown in display). Touch the button once (the icon will light up) to activate the heater at its low level
(700W). Touch the button once more to active the heater at its high level (1300W). When set in high level, touch
the button once again to deactivate the heater.
Note: The fan will continue to run for a short time and turns off automatically after the heater is turned off.
4 TEMPERATURE SETTING BUTTON:
Select the temperature display mode of Celcius (C) or Farenheit (F), simply press and hold button for 10 seconds
to change.
5 TIMER BUTTON:
Set the timer using the button (1 to 8 hours), press button once for 1 hour increments.
6 CHARCOALFIRE BUTTON:
Touch the button to turn charcoal fire on. There are 7 colors in total. Press this button to change color.
The display will show Orange (E1), Green (E2), Blue (E3), Red (E4), Red / Blue (Gradua) E5, Red / Green /
Blue (Gradua) E6, Circle E7
7 BACKLIGHT BUTTON:
Touch the button to turn flame on. There are 4 colors in total . Press this button to change color.
The display will show Orange (C1), Green(C2), Blue(C3), Circle(C4).
LED DISPLAY, Can display temperature, time, background color, flame color, heating switch, high and low heat
MASTER SWITCH
The master switch controls the power supply to the appliance. Turn the switch to “I” to
connect power and turn the switch to “O” to cut the power. There will be a chiming sound
when turning to “O”.
Power (I / O)

REMOTE CONTROL FEATURES
1. Install the CR2025 3V battery in the remote control.
2. Turn the master switch on the e-fireplace to ‘I’ so that it can
receive the signal from the remote control.
3. CAUTION: Never leave the e-fireplace unattended while heating.
4. Refer to Page 12 control buttons/functions for the buttons
on the remote control.
13

TEMPERATURE LIMITING CONTROL
This heater is equipped with a Temperature Limiting Control. Should the heater reach an unsafe temperature,
(115 degrees Celsius) the heater will automatically turn off. To reset: Unplug unit from wall, wait for 5 minutes,
plug back in and continue to use.
Always turn off the fireplace, unplug the unit and let
cool completely before servicing.
TROUBLE SHOOTING
CLEANING
Turn heater OFF and unplug from outlet. Use a vacuum or duster to keep heat and vent area clean from dust
and dirt. The exterior should be cleaned with a damp cloth or duster. Do not use abrasive cleaners, liquid
sprays, or any other cleaner that may scratch the surface.
Wiring may be loose or the
flame motor may be
defective.
Call customer service for
instructions.
SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION
Fireplace
doesn't work.
Fireplace inner components
are overheating or the home
circuit breaker has tripped.
Reset switch by turning
master switch off and waiting
for 5mins, then turning it back
on.
Flame is not
moving.
Flame sputters
Dim or poorly
visible flame or
glass pebbles
aren’t glowing.
LED lights are burnt out or
the wiring is loose.
Call customer service for
instructions.
Call customer service for
instructions.
Flame motor is defective.
Remote control
does not work.
Low battery.
Master switch is in “OFF”
position.
Change the battery for
remote control. Check to
make sure the master switch
is turned on.
Circuit breaker
trips or fuse
blows when the
unit is on.
Improper circuit current
rating.
Call customer service for
instructions.
Heater does not
provide heat
when turned
on.
Thermal switch has been
tripped. Circuit breaker has
been tripped.
Turn the unit off and unplug
the unit for 5mins. Plug back
in and turn on the unit.
Turn off circuit breaker that
supplies electricity to the unit,
wait 5mins, then flip circuit
breaker back on.
Appliance turns
off and will not
turn on.
Appliance has overheated
and its safety device has
caused the thermal switch to
disconnect.
House circuit breaker has
tripped.
Unplug the appliance, allow
to cool for 15mins, then plug
back in.
Reset the house circuit
breaker.
14