CAMBRIDGE X6022-1TEK User manual

MANTEL
MODEL
X6022-1TEK
X6022-1MAH
X6022-1BLK
X6022-1GRY
X6022-1CHR
X6022-1WHT
X6022-1WAL
1REV19-01

3
PACKAGE CONTENTS
Carefully remove all pieces from the carton and make sure that you have all parts listed
(refer to parts list on page 2-3).
6'8: *+9)8/6:/54 7:? 6'8:45
A Top Panel 1
B Left Side Panel 1
C Right Side Panel 1
D Top Shelf Divider 1
E Shelf Rail 1
F1
Right
Trim Panel 1
F2
Left
Trim Panel 1
G1
Right
Inner Panel 1
G2
Left
Inner Panel 1
HBase 1
I Base Back Panel 1
J Base Left Panel 1
K Base Right Panel 1
L
Base Left Support
1
M
Base Right Support
1
N Base Middle Support 1
O Top Shelf 1
P Upper Back Panel 1
Q1Lower Back Panel 1
Q2Lower Back Panel 1
R1Adjustable Shelf
f
1
R2Adjustable Shel 1
S Base Middle Panel 1
T Left Door 1
U Right Door 1
AA Bolt 61
BB Metal Connector 61
CC Shelf Pin 8
DD SPanel crew 24
EE Cabinet Door Hinge 4
FF Handle 2
GG Screw M4X18 2
SS 1
Safety Chain

4
PACKAGE STEPS
1.
2.
AA
[
M
N
L
MNL
X6
J
S
K

5
PACKAGE STEPS
3.
4.
AA X2
[
 [[
;
AA
I
M
N
BB
L

X6
[
I
6
PACKAGE STEPS
5.
6.
BB

X16
AA
7
PACKAGE STEPS
7.
8.
H

BB X16
AA X8
8
PACKAGE STEPS
9.
10.

9
PACKAGE STEPS
11.
12.
G2
AA X3 X3
AA
G1
G1G
F1F2
2

10
PACKAGE STEPS
13.
14.
BB X3
CC X4
BB X3
G1
G1
G2
G2

11
PACKAGE STEPS
15.
16.
BB X4
Q1
Q2

AA X7
12
PACKAGE STEPS
17.
18.
O
BB X3
E

13
PACKAGE STEPS
19.
20.
O
BB X2 BB X2

14
PACKAGE STEPS
21.
22.
X2
B
B
C
C
CC
X2
AA X2
AA
X2
CC

15
PACKAGE STEPS
23.
24. D
X4
BB
X4
BB
X2
BB
X2
AA

AA X6
A
P
16
PACKAGE STEPS
25.
26.

A
BB X6
17
PACKAGE STEPS
27.
28.
R1
R2

18
PACKAGE STEPS
29.
30.
T
EE X2
FF
GG
DD X4
U
EE X2
FF
GG
DD X4

X8
DD
19
PACKAGE STEPS
31.
32.
X8
DD
T
U

20
PACKAGE STEPS
IMPORTANT - Safety Chain Installation
WARNING:
INSTALLATION:
This mantel is heavy furniture. Please be sure to correctly attach the safety chain to both the mantel and an adjacent wall.
Failure to do so can cause serious injury or death.
Assemble the mantel and place it in position
Attach one end of the chain to a wall stud using the screw included
Attach the other screw – through a link in the chain – to the center of the mantel’s top board (you may need to drill a small
starter hole). Put the screw through the chain link that allows the least amount of slack in the chain.
Carefully test that the installed chain adequately prevents tipping or tilting of the mantel.
NOTE: The chain must be as short as possible to prevent the mantel tipping forward. Do not allow slack in the chain.