CAMDEN CV-7600C User manual

Page 1 of 5
Access Control and Telephone Entry
1. GENERAL DESCRIPTION
A key component of a physical security electronic access control
system, a mobile-ready reader combining BLE and contactless
smart card technologies is based on RFID technology.
In operation it is capable of reading data stored on a contactless
smartcard credential via high frequency—or reading data from
mobile credential stored in a smartphone’s wallet app via BLE
technology—and without physical contact, and then passing
the data obtained to the physical access control system.
Access control systems typically manage and record the movement
of individuals through a protected area, such as a locked door.
CV-7600 Series-BLE
Bluetooth Card Reader
INSTALLATION INSTRUCTIONS
2- #6 x 1" Self-Tapping Screws
2- 6-32 x 1" Pan Head Phillips Screws
1- Single Gang Mounting Plate
THIS PACKAGE INCLUDES:
3. SPECIFICATIONS (WITH CARD READER DRAWING)
Input Voltage 8 to 14 VDC
Current Draw 40 mA typical @ 12VDC 195 mA peak
Frequency 13.56 MHz (contactless smartcard) 2.4 GHz (BLE)
Cabling 24 AWG minimum, multi-conductor stranded
with foil shield
Interface Wiegand (26-bit formats), ABA Track II
magnetic strike (clock & data) or OSDP
Operating
Temperature -40°F to 149°F (-40°C to 65°C)
LED Control Blue, Red, Green, Amber and Off
Read Range
Physical: Up to 1.5" (38mm)
Mobile: CV-7600: Up to 1 ft (30 cm)
CV-7615: Up to 15 ft (4.6 m)
Audio Tone Beeper included standard
Protection IP67
Dimensions
Mullion: 1 3/4"W x 11/16"H x 1 13/16"D
(44mm x 119mm x 30mm)
Switch Plate: 3"W x 5 1/8"H x 1 3/16"D
(76mm x 130mm x 30mm)
Notes:
1. Optimized for use with devices supporting BLE version 4.2.
2. Carrying the ETL Label and tested by Intertek, conforms to
UL Standard 294.
3. Self evaluated.
4. Linear power supplies are recommended for best operation.
5. Using CV-MCS Clamshell Contactless Smartcard with 12 VDC at
the reader (other credentials may be less). Read ranges subject
to the smartphone used, the manner in which used, as well as
the installation and it's environment.
6. Ex. Belden 9535 or similar, supporting the ve conductors
comprising the physical layer of the Wiegand interface (power,
ground, data 0, data 1, and/or beeper and LED). Alternatively,
Belden 9539 or similar, for all reader functions. Contact your
access control system manufacturer for specic requirements.
7. CSN = Card Serial Number
1- 6-32 x 1/4" Pan Head Phillips Screw
1- 6-32 x 1/4" Tamper-Resistant Button Head Hex Drive Screw
2. CONEKT WALLET APP
Instructions:
1) Using the target smartphone, download and install the
Conekt Wallet App. The App can be found on the Apple Store or
Google Play Store or by the following link:
http://onelink.to/sb6srb
2) Once installed, launch the Conekt Wallet App, then select the
"+" button to load a new Conekt Mobile Access Credential.
3) When prompted, enter the 16- character Conekt Registration
Key. This will download and activate the Conekt Mobile
Credential. The Conekt Registration Key may be manually
entered or, using the associated QR code, scanned with the
smartphone's camera.
4) The Conekt Mobile Access Credential will now appear in the
Conekt Wallet App, ready to use.

Page 2 of 5
CV-7600 SERIES -BLE BLUETOOTH CARD READER
INSTALLATION INSTRUCTIONS
4. WIRING TO STAND ALONE KEYPAD CM-550SK
Electric
Strike
Door Position Contact
(Normally Closed)
CM-AF142SO
Audible Visual
Annunciator
Door Location
CV-7600 BLE Card Reader
CM-550SK Keypad Reader
120 VAC
Door
Bell or
Chime
Push Button
(Request to Exit)
PS-13
Power
Supply
Transformer
CX-TRX-2012
12 VAC, 20 VA
MOV
D_IN1 (LED) Brown
BELL_A (Pink)
BELL_B (Pink)
ALARM1- (Grey)
NO1 (Blue)
COM1 (Violet)
NC1 (Orange)
AC1 (+12V) Red
GND (Black)
D0 (Green)
D1 (White)
OPEN1(BZ) Yellow
+8-14 VDC
Ground
Data 0
Data 1
RED
BLACK
GREEN
WHITE
5. INSTALLATION (DRAWING, AND MULLION & SINGLE DRAWING)
Each reader must be installed either indoors or outdoors. Mounting options shown below. For installation, use supplied #6
mounting screws or equivalent security screws.
5502 Timberlea Blvd.
Mississauga, ON Canada L4W 2T7
Tel: [phone]
www.camdencontrols.com
A.OLISA
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
CAMDEN DOOR CONTROLS. ANY
REPRODUCTION IN PART OR AS A
WHOLE WITHOUT THE WRITTEN
PERMISSION OF CAMDEN DOOR
CONTROLS IS PROHIBITED.
CV-7000 Series Mullion
and Single Gang
Mounting
12/02/20
4-11/16”
(119mm)
2-5/16”
(58mm)
3-1/4”
(83mm)
2-5/16”
(58mm)
3-1/4”
(83mm)
13/16”
(21mm)
5-1/8”
(131mm)
13/16”
(21mm)
Single Gang Mount
3” (76mm)
Mullion Mount
1-3/4”
(44mm)
ØØ

Page 3 of 5
CV-7600 SERIES -BLE BLUETOOTH CARD READER
INSTALLATION INSTRUCTIONS
Notes:
a) Single Line LED:
This is the standard operating mode and does not make use of
the Orange conductor. The LED is Red when the reader is idle and
ashes when a card is presented. The LED turns Green when the
Brown conductor is pulled low by the access control panel.
b) Dual Line LED:
This mode makes use of both the Brown and Orange
conductors. The Brown conductor controls the Red LED and
the Orange conductor controls the Green LED. LED states are
determined by the access control system option and capability.
WIEGAND
Wire Color Function
RED DC (8 -14 VDC)
BLACK Ground
GREEN DATA 0
WHITE DATA 1
BROWN RED LED (a)
ORANGE GREEN LED (b)
YELLOW NOT USED
BLUE BEEPER
VIOLET READ MODE (c)
DRAIN SHIELD GROUND
c) Read Mode:
In regards to contactless smart card credentials, the reader will
only read and output the credential's Card Serial Number (CSN)
when the Violet conductor is pulled low (connected to ground).
Otherwise, the reader will only read and output the credential's
programmed Sector data.
Unused conductors should be trimmed, isolated and taped
back to prevent unintended current ows. Apply positive
voltage only to the Red DC Conductor.
a) Cable Requirements:
24 AWG minimum, multi-conductor stranded with an overall
foil shield, for example Belden 9535 or similar, supporting the
ve conductors comprising the physical layer of the Wiegand
interface (power, ground, data 0, data 1, and/or beeper and LED).
Alternatively, Belden 9539 or similar, for all reader functions.
Contact your access control system manufacturer for their
specic requirements. Per the SIA’s Wiegand specication,
maximum cable length is 500 feet (152 m).
b) Output Formats:
Wiegand (industry standard 26-bit Wiegand and custom
Wiegand formats).
c) Grounding:
Shield (drain) continuity must run from the reader to the access
panel. Shield (drain) and reader ground must be tied together at
the access panel and connect to an earth ground at one point.
d) Power:
Reader may be powered by the access control panel. A linear
power supply is recommended for best operation. 8 to 14 VDC,
12 VDC at the reader is best.
e) Read Mode:
For sector data reads, do not connect the Violet conductor
(leave it high). For CSN reads, pull the Violet conductor low
(connect the Violet conductor to ground).
Reader Model Read Range
CV-7600 1 foot
CV-7605 5 feet
CV-7615 15 feet
CV-7630 30 feet
CREDENTIAL
Model Description
CV-MBT BLE Mobile Credentials
CV-MCS Mobile Clam Shell Cards
CV-MKT Mobile Key Fob, 2K memory

Page 4 of 5
CV-7600 SERIES -BLE BLUETOOTH CARD READER
INSTALLATION INSTRUCTIONS
Card Reader
Card Reader
Back Case Single Gang Mount
Back Case Mullion Mount
Wall
Wall
6-32 x 1/4'' Phillips or
Tamper Resistant Screw
6-32 x 1/4'' Phillips or
Tamper Resistant Screw
#6 Self-Tapping Screw
or
6-32 x 1” Phillips Screw
#6 Self-Tapping Screw
or
6-32 x 1” Phillips Screw
5502 Timberlea Blvd.
Mississauga, ON Canada L4W 2T7
Tel: [phone]
www.camdencontrols.com
A.OLISA
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
CAMDEN DOOR CONTROLS. ANY
REPRODUCTION IN PART OR AS A
WHOLE WITHOUT THE WRITTEN
PERMISSION OF CAMDEN DOOR
CONTROLS IS PROHIBITED.
CV-7600 Series Card
Reader
04/06/20
13
4''
[44mm]
11
4''
[31mm]
1''
[25mm]
4
11
16''
[119mm]
3''
[76mm]
11
4''
[32mm]
51
8''
[131mm]
1''
[26mm]
Mullion Mount Single Gang Mount
CV-7600 Series Card Reader Dimensions

Call: 1.877.226.3369 / 905.366.3377
Visit: www.camdencontrols.com
Opening New Doors to
Innovation, Quality and Support!
Page 5 of 5
CV-7600 SERIES -BLE BLUETOOTH CARD READER
INSTALLATION INSTRUCTIONS
File: CV-7600-BLE_Manual_v2.indd
Rev.: 06/08 -/2020
Part No: 40-82B244
6. TROUBLESHOOTING
a) When the reader is rst powered on it will beep 4-times,
and the LED will shine red.
b) Presenting a supported access credential will result in the
reader beeping and the LED ashing once.
c) Mobile operation is optimized for smartphones supporting
BLE (Bluetooth LE) version 4.2 or newer. Further, for the
downloading of mobile access credentials, a stable, high-
quality internet connection is recommended.
Note:
The access panel controls LED functionality, such as switching
the LED to green. If the reader does not recognize the mobile
credential, card, tag (no beep, no LED ash) or exhibits short
read range, see table below for possible causes and solutions.
Possible Cause Corrective Action
Incorrect cabling Verify gauge, connections
and cabling length
Not enough power 12 VDC recommended
Incorrect credential used Verify if credential technology
is supported
Reader/access panel not
properly grounded
Earth ground needed—verify
shield and reader ground are tied
at access panel and connect
to ground at one point
Supply generating
interference
Linear power supply
recommended, verify
switching power supply
before use
Should any of the corrective actions mentioned above not
improve performance, disconnect the reader from the access
panel and power it with a separate power supply or 9 VDC
battery, and re-test card functionality.
By powering the readers separately, most variables that may
lead to reduced performance can be eliminated. Should the
problem persist, please contact Camden directly.
FCC Compliance Statement
This device complies with part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Caution:
Changes or modications not expressly approved by Camden
Door could void the user's authority to operate the equipment.
Product can be used without license conditions or restrictions
in all European Union countries, including Austria, Belgium,
Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Poland, Portugal,
Romania, Slovakia, Spain, Sweden, Unite Kingdom as well
as other non-EU countries, including Iceland, Norway and
Switzerland.
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may
cause undesired operation of the device. Camden Controls
reserves the right to change specications without notice.
Cet appareil est conforme à Industrie Canada exempts de
licence standard RSS (s). Le fonctionnement est soumis
aux deux conditions suivantes : (1) ce dispositif ne peut pas
provoquer d’interférences et (2) ce dispositif doit accepter toute
interférence, y compris les interférences qui peuvent causer un
mauvais fonctionnement du dispositif.
Note:
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the
equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference
to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference
in which case the user will be required to correct the
interference at his own expense.