Camos CM-708R User manual

7”TFT LCD
7
LANGUAGE
VEHICLE
INSTRUCTION MANUAL
CM-708R
7”TFT LCD COLOR MONITOR
Thank you for purchasing this product.
For proper usages and application,
please read this instruction manual thoroughly.
PRINTED IN KOREA ver. 1.0

2
CONTENTS
SAFEGUARD INSTRUCTIONS -------------------------------------- 3
FEATURE ----------------------------------------------------------------- 5
BOX CONTENTS ------------------------------------------------------- 5
FUNCTION OF EACH PART ---------------------------------------- 6
FUNCTIONS ------------------------------------------------------------- 8
CHANGING REMOTE CONTROL BATTERY -------------------- 12
CONNECTIONS ------------------------------------------------------- 13
INSTALLATION -------------------------------------------------------- 14
SPECIFICATION ------------------------------------------------------ 15

3
7”TFT LCD COLOR MONITOR
WARNING
This information is for preventing bodily harm or even death and
use should follow this safety rules.
SAFEGUARD INSTRUCTIONS
Please read the “Safety Rules” carefully before using this product. Following
the safety rules prevents users from damages related with the misuse of the
product. It is very important to follow these safety rules. We state “Caution” and
“Warning” to clarify any potential risk for a damage associated with the misuse
of the product.
CAUTION
This information is for preventing damage or shorten the life time
of the products.
CAUTION
Unplug product when do not use for a long time.
--- It may case fire by short circuit due to heating.
Do not place near magnet.
--- It may cause malfunction and trouble.
Should install while power off. (After install products, connect DC jack)
--- It may cause to electronic shock or malfunction.
While stop driving (parking), set the car in motion.
--- It may cause battery discharge.
Do not use multi socket or extended adaptor.
--- It may cause unexpected heating, fire and malfunction.
The battery for remote controller is not rechargeable and should
replace same or similar model. Used battery may cause environmental
pollution, so trash it carefully.
--- This may cause a malfunction and problem.
In case of inserting battery, attend to polarity and insert according to
direction.
--- When wrong inserting, it may cause fire, damage by explsion.
Do not push a LCD panel.
--- It may cause LCD broken.

4
Do not clean exterior with volatility or oily solvent.
Neither keep touching rubber and plastic for long time.
--- It may cause change of surface, fall of paint, malfunction and re.
Do not place where vibration and shock.
--- It may cause throw down and then malfunction and accident.
Do not put a pin or needle on the hole or crack in the body.
--- In case of inserting them, stop to operate, it may cause electronic
shock, re and malfunction.
Do not use in problem condition as like smoking, smell something
burn.
--- It may cause re. Stop to use and make inquiries to agency.
Do not disassemble, repair and remodeling.
--- It may cause malfunction and injury, can not get warranty.
--- Make inquiries to agent for repair and checkup.
WARNING
Do not put the product in place where sudden temperature increasing
and should use on optimum voltage, temperature and humidity
--- It may cause to electronic shock or malfunction.
Do not place where interfere with visual eld and watch or operate
monitor during driving.
--- It may cause trac accident.
Do not get product wet and operate with wet hands.
--- It may cause to electronic shock or malfunction.
Keep clean dust on power socket.
--- It may cause electronic shock and re by bad connection.
Do not pull cord with a jerk, should catch a plug and pull.
Do not use damaged cord.
--- It may cause cord malfunction, electronic shock and re.
When clean exterior, power o and wipe with dry cloth.
--- Wet cloth may cause a electronic shock.

1
2
5
7”TFT LCD COLOR MONITOR
7”TFT LCD COLOR MONITOR
• 8bit MICRO controller
• TFT LCD with high resolution and low reflection
• All functions are displayed on screen (OSD function)
• PWM volume control
• Mode selection function
• Low energy consuming rate
• Language Display Selection (KOR-JPN-GER-ENG-SPA-FRE-ITA)
• 4 Screen Mode (FULL-WIDE-NORMAL-CINEMA)
• Free voltage (From DC 12V to DC 24V)
• Dimmer selection function
Monitor
FEATURE
BOX CONTENTS
Stand Monitor Cable
Cigar Cable Manual Remote Control
TRG
Extension Cable

3
6
7”TFT LCD COLOR MONITOR
Power or Stand-by status display
Power ON/OFF button
CAM1/CAM2/AV selection function
SETUP/PICTURE selection function
SOUND/MENU level control
FUNCTION OF EACH PART
①S/BYLED
②POWER
③MODE
④MENU
⑤UP/DOWN
[ MONITOR ]

7
Power ON/OFF button
Selecting CAM1/CAM2/AV
Selecting MENU and changing functions
Changing volume or MENU level
Moving Up/Down on MENU
Mute mode On/Off
Displaying the current channel and volume level
Adjusting the screen setting
①POWER
②MODE
③MENU
④VOL◀▶(VOL+-)
⑤CH▲▼
⑥MUTE
⑦RECALL
⑧AUTOPIC
[ REMOTE CONTROLLER ]

8
4
CAM1
70
VOLUME
30
VOLUME
CAM1 CAM2 AV
7”TFT LCD COLOR MONITOR
MODE2
1) Press [MODE] button.
2) CAM1/CAM2/AV appears on the screen
and it is disappearing 5 seconds after
setting.
FUNCTIONS
POWER1
ON OFF
1) Press [POWER] button to the power.
(STAND BY state is OFF)
2) Press [POWER] button again to off the
power. (STAND BY state is ON)
• It is a function to change video signal.
UP/DOWN3
• Press VOL◀▶(VOL+/-) button on remote control or UP/DOWN button on monitor to ad-
just volume.

DIMMER
LANGUAGE
DIRECTION
DISPLAY
MARKER
RESET
ENGLISH
0˚
FULL
OFF
▶
CONTRAST
BRIGHTNESS
COLOR
TINT
70
70
50
50
DIMMER
LANGUAGE
DIRECTION
DISPLAY
MARKER
RESET
ENGLISH
0˚
FULL
OFF
▶
DIMMER
LANGUAGE
DIRECTION
DISPLAY
MARKER
RESET
ENGLISH
180˚
FULL
OFF
▶
9
MENU4
SETUP PICTURE CAMERA
2) Press [MODE] button to select SUB MENU, UP/DOWN button to change SUB MENU.
• DIMMER
[ 1. SETUP ]
• LANGUAGE
ENGLISH DEUTSCH ITALIANO FRANCAIS
ESPAnOL 한국어 日本語
• DIRECTION
• It is a function to select MAIN MENU (SETUP/PICTURE/CAMERA)
1) Press [MENU] button to select MAIN
MENU, changed color in red when it
is selected.

10
• DISPLAY
• MARKER
WIDE NORMAL CINEMA FULL
DIMMER
LANGUAGE
DIRECTION
DISPLAY
MARKER
RESET
ENGLISH
0˚
FULL
OFF
▶
-Theonscreendistancemarkersshouldbeconsideredasageneralreferencetoassist
thedriverinassessingthedistancesdepictedonthescreen.Thedistancemarkers
havebeendesignedbasedonthe“CCDcamerainstallationconditions”listedinthe
next section, but differences in vehicle design and construction may result in the
actualinstallationconditionorlocationbeingdifferentfromtheconditionslisted.In
suchcases,thedisplaylocationshouldbesetattheclosestmarkerNo.
-DistancemarkerscannotbesetifnonCAMOScamerasareused.
Warning
-Themarkersmaynotindicatetheexactpositionofthebumper,thevehicleʼswidthor
thedistancetotherear.Useasareferenceonly.
Caution
(1) Press MENU button on CAM1, full screen mode.
(2) Press MODE button and select MARKER.
(3) Then, press [DOWN/UP] button on the monitor
or [◀▶] button on the remote control, select
ON.
* It is set OFF from the factory.
MARKER
SELECT
Ｐ１ ７ｍ
５ｍ
３ｍ
１ｍ
Bumperposition
(Frombumper
towardrear)
Vehiclewidth
■CCDcamerainstallationconditions
(distancemarkerinputconditions)
(Unit：mm)
MarkerNo.
(Pattern)
CameraInstall
Height
Vehicle
Width
Ｐ１
Ｐ２
Ｐ３
Ｐ４
Ｐ５
Ｐ６
Ｐ７
２，０００
２，２５０
２，５００
２，７５０
３，０００
３，２５０
３，５００
２，５００
２，３００
２，５００
<MARKERSELECT>
(1)PressMENUbuttonandselectMARKERSELECTmenu.
(2)Press [DOWN/UP] button on the monitor or [◀▶] button on the remote control, and
switchmarkerpattern.
* Distance marker function setting is only possible when MARKER is selected on CAM1,
full screen mode.

11
<MARKERADJUST>
(1)PressMENUbuttonandselectMARKERADJUSTmenu.
(2) Press MODE button and select H / V. (H: horizontal / V: vertical )
(3)Press [DOWN/UP] button on the monitor or [◀▶] button on the remote control,and
switch marker pattern. (H = -10~+10, V= -12~+12, Default setting: H=0, V=0)
(4) After 10 seconds, set up screen disappears, and set up finishes.
* If there is no button operation, set up screen disappears even during set up process.
A factory default reset will clear all of OSD information.
• RESET ▶

CONTRAST
BRIGHTNESS
COLOR
TINT
50
50
50
50
CONTRAST
BRIGHTNESS
COLOR
TINT
50
50
50
50
CONTRAST
BRIGHTNESS
COLOR
TINT
50
50
50
50
CONTRAST
BRIGHTNESS
COLOR
TINT
50
50
50
50
CAM1 MIRROR
12
[ 2. PICTURE USER ]
1) [MODE] button to select CONTRAST, BRIGHTNESS, COLOR, TINT MENU.
(Selected menu in red)
2) Push [UP/DOWN] button to change the settings of the diferent menu points.
[ 3. CAMERA ]
1) Press the mode button to choose CAM1;
CAM2 will turn red.
2) Press the VOLUME UP, DOWN button.
NORMAL/MIRROR sign will be appear in
order to adjust the screen to the right or
left or to reverse the image. NORMAL/
MIRROR signal will turn RED.
* NOTICE : If MIRROR mode is selected, the right and left of screen image will be re-
versed. However, any letters will be not be reversed.

CONTRAST
BRIGHTNESS
COLOR
TINT
50
50
50
50
CAM1
30
VOLUME
13
• This function can be operated by the remote control.
MUTE6
• When press the AUTO PIC button, PICTURE SETUP menu is displayed on screen.
AUTOPIC5
RECALL7
1) Press [MUTE] button to mute sound and display
mute icon.
1) Press [RECALL] button to check the MODE and
Volume.

5
14
7”TFT LCD COLOR MONITOR
CHANGING REMOTE CONTROL BATTERY
1. Pull the battery cover to the
direction of the arrow.
2. Place a battery with the (+) sign
upward. (No. CR2025)
3. Put the battery case back into the
remote control in the direction of
the arrow.

6
15
7”TFT LCD COLOR MONITOR
CONNECTIONS
CAMERA 1 CAMERA 2 BLACK(CAMERA1) GREEN(CAMERA2) VIDEO AUDIO DC INPUT
CAMERA(OPTION)
CIGAR CABLE
MDM-105A
BLACK (CAMERA 1, Priority) FOR REAR VIEW
Connect this line to “+” of reverse light lamp.
GREEN (CAMERA 2) FOR SIDE VIEW
Connect this line to “+” of side light lamp.

7
Protect tape
Control Konb
(Angle)
Tapping Screw
Fix Knob
(Bracket)
Stand
16
7”TFT LCD COLOR MONITOR
INSTALLATION
(1) Please set the place for Monitor installation. Clean the place where to install
stand and install stand firmly after removing protect tape of stand bottom.
(2) Fix the stand with enclosed screws.
(3) Assemble the monitor to stand and fix it in the right angle.
(4) Connect cable as follows.

17
AUTO (NTSC/PAL)
Composite Video 75Ω 1Vp-p
7 Language
-30˚C ~ 70˚C
-40˚C ~ 80˚C
201(W) x 117(H) x 30.7(D) mm
450g
7”TFT LCD COLOR MONITOR
8SPECIFICATION
LCD PANEL
POWER SUPPLY
INPUT SYSTEM
FREQUENCY
VIDEO INPUT SIGNAL
OSD DISPLAY
OPERATING TEMPERATURE
STORAGE TEMPERATURE
DIMENSION
WEIGHT
SCREEN SIZE
DISPLAY FOMAT
BRIGHTNESS
Contrast ratio
ACTIVE AREA
VIEW ANGLE
VOLTAGE
CONSUMPTION
HORIZONTAL
VERTICAL
17.78 cm (7.0 inch)
800(H) x 3(RGB) x 480(V)
400 cd/m2
500:1
154.08 (W) x 86.92 (H) mm
70˚(L) / 70˚(R) / 50˚(U) / 70˚(D)
DC 12V - 24V
450mA Max (DC 12V, Monitor Set Only)
** The design and specications of this product in order to improve its quality may be
changed without notice.
15.734 Khz
60 Hz
15.625 Khz
50 Hz
NTSC PAL
SPECIFICATION
ITEM

MEMO

MEMO

INSTRUCTION MANUAL