Camos CM-709M2 User manual

CM-709M2
INSTRUCTION MANUAL
7”4CHANNEL DIGITAL MONITOR
Thank you for purchasing this product.
For proper usages and application,
Please read this instruction manual thoroughly.

2
CONTENTS
SAFEGUARD INSTRUCTIONS
FEATURE
CONTENT
FUNCTION OF EACH PART
FUNCTION
SETTINGS
CONNECTING AND INSTALLATION
SPECIFICATION
.................................... 3
............................................................................ 5
....................................................................... 5
........................................ 6
........................................................................ 8
.......................................................................... 13
..................... 17
............................................................. 18

3
7”4CHANNEL DIGITAL MONITOR
This information is for preventing bodily harm or even death and use
should follow this safety rules.
SAFEGUARD INSTRUCTIONS
Please read the “Safety Rules” carefully before using this product. Following the safety
rules prevents users from damages related with the misuse of the product. It is very
important to follow these safety rules. We state “Caution” and “Warning” to clarify any
potential risk for a damage associated with the misuse of the product.
This information is for preventing damage or shorten the life time
of the products.
This information is for user’s reference for better usability.
WARNING
CAUTION
NOTICE
CAUTION
Do not use multi socket or extended adaptor.
- It may cause unexpected heating, fire and malfunction.
If the product is not used for longer time, please unplug it.
- It may case fire by short circuit due to heating.
Do not place near magnet.
- It may cause malfunction.
Please install while power off. (After install products, connect DC jack)
- It may cause electronic shock or malfunction.
Before installallation of the body, take enough place at least more than 15cm from the
wall to emit heat.
The battery for remote control is not rechargeable and should be replaced by same or
similar model.
- This may cause malfunction and problems.

4
WARNING
Take care that the product doesn’t get wet.
- It may cause electronic shock or malfunction.
Do not install the product where sudden temperature increasing could be and use
the optimum voltage, temperature and humidity.
- It may cause electronic shock or malfunction.
Do not place near of air bag effective range.
- It may cause malfunction of air bag or accident, injury due to hitting monitor by
air bag.
Do not pull cord with a jerk, should catch a plug and pull. Do not use damaged cord.
- It may cause cord malfunction, electronic shock and fire.
Keep cleaning dust on power socket.
- It may cause electronic shock and fire by bad connection.
Do not clean exterior with volatility or oily solvent.
Neither keep touching rubber and plastic for long time.
- It may cause change of surface, fall of paint, malfunction and fire.
When clean exterior, power off and wipe with dry cloth.
- Wet cloth may cause a electronic shock.
Do not place where vibration and shock could be.
- It may cause throw down and then malfunction and accident.
Do not put a pin or needle or try to crack the body.
- In case of inserting them, stop to operate, it may cause electronic shock, fire and
malfunction.
Do not use in problem condition like smoking, smell something burn.
- It may cause fire. Stop to use and make inquiries to agency.
Do not disassemble, repair and remodeling.
- It may cause malfunction and injury, can not get warranty.
- Make inquiries to agent for repair and checkup.

1
2
※ Design and specications could be changed without notices.
5
7”4CHANNEL DIGITAL MONITOR
7”4CHANNEL DIGITAL MONITOR
• 7” Wide digital TFT LCD with high resolution and low reflection
• All functions are displayed on screen (OSD function)
• 7 language display (ENG-DEU-ITA-FRA-ESP-KOR-JPN)
• DC 12~24V
• Touch buttons in front and including remote control
• Max. 4 camera and 2 A/V input (Video / Mono Audio)
• Camera input screen reversion (Normal / Mirror mode)
• User can choose split screen ( 2/ 3/ 4 / H Split screen)
• 4 Triggerlines one for each camera
• Illumination sensor adopting
• NTSC/PAL (User can choose manually)
Monitor
FEATURE
CONTENT
Stand Remote Control Monitor cable
Cigar cable
Trigger
extension cable
※ When you open the gift box, please check below contents. If you find missing parts,
please contact sales place.
Sun visor Manual

3
6
7”4CHANNEL DIGITAL MONITOR
FUNCTION OF EACH PART
[MONITOR]
AV MODE DOWN/UP MENU
SENSOR
(REMOTE)
POWER
① IR-SENSOR
② AV
③ MODE
④ DOWN/UP
⑤MENU
⑥ POWER
IR-SENSOR
Go into AV mode directly and change to AV input
Choose split screen (Full/2/3/4 split), choose audio output
Choose cam input on full screen mode, split mode and change on split
screen, volume control, menu setting change
OSD menu on/off, screen input information
Power on/off

①
④
⑦
②
⑥
⑨
③⑤
⑧
⑫
⑪
⑩
7
[REMOTECONTROLLER]
① POWER
② AV
③ OK
④ ◀▶
⑤ ▲▼
⑥ VOL +/-
⑦ MUTE
⑧ SETUP
⑨ RECALL
⑩
⑪
⑫
Power On/Off
Go into AV mode directly and change to AV input
Choose button on menu
Menu setting adjusting
Choose full screeen mode and menu adjusting
Volume control
Mute On/Off
OSD Menu setup
Actual settings
Go into 2 split screen
Go into 3 split screen
Go into 4 split screen

4
CAM3
VOLUME 30
AV MODE DOWN/UP MENU POWER
CAM1
AV MODE DOWN/UP MENU POWER
AUX1
VOLUME 30
8
POWER ON/OFF
1
7”4CHANNEL DIGITAL MONITOR
FUNCTION
After connecting cigar jack, press POWER button on remote control or monitor
then the picture of the camera will be shown on the monitor.
※ If there is no image, the screen will be BLACK.
VOLUME CONTROL
2
CAM 1 image signal receive No image signal
Press VOL +/- button on remote control or Down/Up button on monitor to adjust
volume.
※ Volume can be adjust within 1~100 and it is set 30 from the factory.
※ Almost all video inputs have audio output, except side cameras.
※ In case of choosing a camera without audio or there is no signal, there will be
no sound and volume control available.

MUTE
AV MODE DOWN/UP MENU POWER
FULL 2 SPLIT 3 SPLIT 4 SPLIT
→→→
→
9
Press MUTE[ ]button on remote control for MUTE function ON/OFF. When
MUTE is ON it will be displayed. It disappears for a while OSD MENU is used.
※ When user controls volume while mute function is set, the mute function turns
off.
MUTE ON/OFF
3
SCREEN SPLIT MODE SWITCH : FULL / 2 / 3/ 4 SPLIT
4
Press M(Mode) on monitor, then the screen switches as below order.
※ User can choose split screen directly with split button on remote control.
2 SPLIT 3 SPLIT 4 SPLIT

AV MODE DOWN/UP MENU POWER
AV MODE DOWN/UP MENU POWER
CAM1 CAM2 CAM3 CAM4
→→→
→
10
2 SPLIT
2 SPLIT
3 SPLIT
3 SPLIT
4 SPLIT
H 4 SPLIT
CHANGE SPLIT MODE
5
Each split screen has two options. On split mode, press DOWN/UP button of
monitor or split screen button of remote control then the screen switches between
both options.
CHANGE INPUT
6
On split or AV mode, press ▲ button on remote control (or UP button of monitor)
then it will change camera input of CAM1~CAM4 as below order.
※ In case of press ▼button on remote control then it changes in reverse order.
To use the monitor button, go into full screen by pressing M(MODE) button and
use DOWN/UP button.
1) Camera mode

AV MODE DOWN/UP MENU POWER
AV MODE DOWN/UP MENU POWER
AUX1 AUX2
• Split screen
SPLIT SCREEN SETUP
SET LEFT SIDE
SET RIGHT SIDE
CAM3
SELECT INPUT
CAM1
CAM2
CAM3
CAM4
AUX1
AUX2
11
To choose the OSD MENU [SETUP] on each split mode, press menu button of moni-
tor or SETUP button of remote control.
3) SPLIT mode
On camera mode, press AV button of monitor or remote control then the screen
goes to AV mode directly.
2) AV mode
User can change camera mode on each split screen. Press M(MODE) button of moni-
tor or DOWN/UP button of remote control and choose a Camera.
Notice ※ It is same way for every split screen mode.

CAM1 CAM3CAM1
CAM1 CAM4 CAM2
CAM1 TRIGGER SETUP
FULL SCREEN
SPLIT SCREEN
CAM3 CAM2CAM2
CAM2 TRIGGER SETUP
FULL SCREEN
SPLIT SCREEN
12
SCREEN SWITCH WHILE TRIGGER INPUT
7
<Trigger input> or <trigger signal> is when a circuit works by a signal, for example if
driver uses right/left turn signal or reverse gear, the monitor shows connected camera
on driving mode.
※ Below example is based on {TRG1 (Left turn signal)=CAM1 / TRG2 (Right
turn signal)=CAM2 / TRG3 (Reverse gear)=CAM3 / TRG4 (Front or something
else)=CAM4 }.
1) If there is a trigger signal input, the connected camera is displayed as full screen
and switches back when the signal switches off.
Formerscreen CAM2 signal input
2) In case of TRG1 (Left turn signal) or TRG2 (Right turn signal), you can choose
full screen or split screen by OSD setting.
※ This function is for showing not only Left(Right) but also rear side at once,
regardless former screen status. It displays CAM1(2) and CAM3 as split screen
while TRG1(2) signal input.
If there is the right signal input
(TRG2),then CAM2 (Right) in
right side and CAM3 (Rear) in
left side will be shown on the
screen.
Press MENU [ ] button of mo-
nitor or SETUP button of remote
control on CAM1 full screen
mode, then OSD menu appears.
Press DOWN button of monitor
or ▼button of remote control on
CAM1 full screen to move [SPLIT
SCREEN] and press ▶button.
If there is the left signal input
(TRG1),then CAM1 (Left) in left
side and CAM3 (Rear) in right
side will be shown on the screen.
Press MENU [ ] button of mo-
nitor or SETUP button of remote
control on CAM2 full screen
mode, then OSD menu appears.
Press DOWN button of monitor
or ▼button of remote control on
CAM2 full screen to move [SPLIT
SCREEN] and press ▶button.

CAM1 CAM3
CAM3
CAM3 CAM2
CAM1 CAM4 CAM1 CAM2
CAM3 CAM4
13
3) When there is the TRG3(Rear light) input, CAM3 will be shown as full screen
and user can also choose 2 split screen.
※ This function is available for rear and side screen.
Press ▼button of remote control
(or DOWN button of monitor),
then it shows 2 split screen as
right for CAM3 (Rear) and left
for CAM1.
When the reverse gear input, the
screen displays CAM3 (Rear) as
full screen.
Press ▲button of remote con-
trol (or UP button of monitor),
then it shows 2 split screen as
left for CAM3 (Rear) and right
for CAM2.
4) In case of hazard flasher (TRG1+TRG2), the monitor displays CAM1~CAM4
as quad split screen. And the screen switches back when the signal switch-
es off.
2 split screen using In case of hazard flasher,
4 split screen display

14
5) When there is an input signal of more than 2 triggers, the monitor displays fully
connected screen (Trigger input screen) as the priority order. And the screen
switsches back when the signal switsches off, the rest will be displayed as the
priority order
CAM1 CAM4 CAM2
AUX CAM1
CAM1
AUX CAM1
CAM3
CAM1 CAM2
CAM4CAM3
Formerscreen
Formerscreen
Formerscreen CAM 3 signal output
※ If the screen turns to trigger signal, only volume, mute and audio out choice
available.
※ If there is trigger signal input while power off (Stand-by) status, the screen
switsches on and displays choosen trigger line (camera). And the screens turns
off when the trigger signal switsches off.
CAM 2,3,4 simultaneous
signal input
※ TRIGGER PRIORITY ORDER
CAM3 > CAM1+CAM2 > CAM1 > CAM2 > CAM4
NOTICE
CAM 1,4 simultaneous
signal input
CAM 1,2 simultaneous
signal input
CAM 4 signal output
CAM 2 signal output

5
PICTURE SETUP
DIMMER AUTO
BRIGHT 50
CONTRAST 50
HUE 50
SATUREATION 50
LANGUAGE ENGLISH
VIDEO SYSTEM NTSC
RESET >
PICTURE SETUP
DIMMER AUTO
BRIGHT 50
CONTRAST 50
HUE 50
SATUREATION 50
LANGUAGE ENGLISH
VIDEO SYSTEM NTSC
RESET >
AV MODE DOWN/UP MENU POWER
AV MODE DOWN/UP MENU POWER
15
Video Standard System, NTSC/PAL conversion
1
If use PAL system on NTSC system using country, it may cause a malfunction. This
products can convert NTSC/PAL system manually but it is not automatic. Before use,
please check and set the system.
7”4CHANNEL DIGITAL MONITOR
SETTINGS
Dimmer sensor setting
2
※ User can choose DAY/NIGHT/AUTO and it is set AUTO from the factory.
1) Press SETUP button of remote control
(or MENU button of monitor) to go into
OSD MENU [PICTURE SETUP].
2) Move to DIMMER by pressing ▼button
of remote control (or MODE button
of monitor) then choose by pressing
◀▶button (or DOWN/UP button of
monitor)
1) Press SETUP button of remote control
(or MENU button of monitor) to go into
OSD MENU [PICTURE SETUP].
2) Move to VIDEO SYSTEM by pressing
▼ button of remote control (or MODE
button of monitor) then choose
video standard system by pressing
◀▶button (or DOWN/UP button of
monitor)
Attention
NTSC system country : USA, CANADA, JAPAN, KOREA, TAIWAN, MEXICO
PAL system country : AUSTRALIA, BELGIUM, CHINA, DENMARK, FINLAND,
GERMAN, U.K, NETHERLAND, ITALY, KUWAIT,
MALAYSIA, NEW ZEALAND, SIGNAPORE, SPAIN,
SWEDEN, TAILAND, NORWAY.

PICTURE SETUP
DIMMER AUTO
BRIGHT 50
CONTRAST 50
HUE 50
SATUREATION 50
LANGUAGE ENGLISH
VIDEO SYSTEM NTSC
RESET >
PICTURE SETUP
DIMMER AUTO
BRIGHT 50
CONTRAST 50
HUE 50
SATUREATION 50
LANGUAGE ENGLISH
VIDEO SYSTEM NTSC
RESET >
AV MODE DOWN/UP MENU POWER
AV MODE DOWN/UP MENU POWER
16
Brightness and contrast setting
3
User can control BRIGHT/CONTRAST/COLOR/HUE/SATUREATION.
※ Each menu is set 50 from the factory.
1) Press SETUP button of remote control
(or MENU button of monitor) to go into
OSD MENU [PICTURE SETUP].
2) Move to each menu what by pressing
▼button of remote control (or MODE
button of monitor) then choose as by
pressing ◀▶button (or DOWN/UP
button of monitor)
Language setting
4
※ It supports 7 languages and is set ENGLISH from the factory.
1) Press SETUP button of remote control
(or MENU button of monitor) to go into
OSD MENU [PICTURE SETUP].
2) Move to LANGUAGE by pressing ▼
button of remote control (or MODE
button of monitor) then choose by
pressing ◀▶button (or DOWN/UP
button of monitor)

PICTURE SETUP
DIMMER AUTO
BRIGHT 50
CONTRAST 50
HUE 50
SATUREATION 50
LANGUAGE ENGLISH
VIDEO SYSTEM NTSC
RESET >
AV MODE DOWN/UP MENU POWER
AV MODE DOWN/UP MENU POWER
17
Initialization
5
※ It initializes monitor as from the factory mode. (Except on Video Standard System,
NTSC/PAL)
1) Press SETUP button of remote
control(or MENU button of monitor)
to go into OSD MENU [PICTURE
SETUP].
2) Move to SETUP by pressing ▼button
of remote control (or MODE button
of monitor) then choose by pressing
◀▶button (or DOWN/UP button of
monitor)
AUDIO Output
6
On split mode, user can choose 1 screen for audio
output.
1) Press ◀▶button of remote control
(or MODE button of monitor) for 1
second, then speaker icon appears
where audio out is used.
2) Whenever press ◀▶button of remote
control (or MODE button of monitor)
the icon move to other screen.

MIRROR SET
CAM1 MIRROR
CAM2 MIRROR
CAM3 MIRROR
CAM4 MIRROR
AV MODE DOWN/UP MENU POWER
CAM1 CAM2
CAM3 CAM4
VOLUME 30
AV MODE DOWN/UP MENU POWER
18
CAMERA Mirror/Normal mode setting
8
Screen Information
7
Press MODE button of monitor or RECALL button of remote control, then it displays
actual screen information (Input mode / Audio output / Volume).
1) Press SETUP button of remote control
(or MENU button of monitor) to go into
OSD MENU [MIRROR SET].
2) Move to a camera which by pressing
▼button of remote control (or MODE
button of monitor) then choose by
pressing ◀▶button (or DOWN/UP
button of monitor).
※ It is set MIRROR mode from the
factory.

6
VELCRO TAPE
VELCRO TAPE
NOTICE
⑤
⑥
⑥
TAPPING SCREW T1 M4.0 X 12 (3ea)
INSERT BOLT (2ea)
FLAT WASHER M3 (4ea)
19
7”4CHANNEL DIGITAL MONITOR
CONNECTING AND INSTALLATION
(1) Clean the place where to install stand and install stand rmly after
removing protect tape of stand bottom.
(2) Fix the stand with enclosed screws.
(3) Assemble the monitor to stand and x it in the right angle.
(4) Connect cable as follows.
※ Installation can be changed as user’s pleasure.

RED (DC JACK) WHITE (AUDIO1) YELLOW (VIDEO1) ORANGE (RIGHT) GREEN (LEFT) BLACK (REAR) RIGHT LEFT REAR1 REAR 2 WHITE (AUDIO2) YELLOW (VIDEO2) CVBS
RIGHT CAMERA
LEFT CAMERA
REAR 1 CAMERA REAR 2 CAMERA (OPTION)
(OPTION)
(OPTION) (OPTION)
20