Camos CM-800D User manual

CM-800D
INSTRUCTION MANUAL
INSTRUCTION MANUAL
8”TFT LCD DIGITAL COLOR MONITOR
Thank you for purchasing this product.
For proper usages and application, Please read this instruction manual thoroughly.
PRINTED IN KOREA ver. 1.0

2 3
CONTENTS
SAFETY RULES
BEFORE USE
SPECIAL FEATURES OF THE PRODUCT
TERMS OF PART
REMOTE CONTROL
FUNCTIONS
CONNECTIONS
CHANGING REMOTE CONTROL BATTERY
SPECIFICATIONS
................................................................... 3
....................................................................... 5
........................ 5
................................................................. 6
........................................................... 7
........................................................................ 8
................................................................ 12
................ 14
............................................................. 15
8”TFT LCD DIGITAL COLOR MONITOR
WARNING
This information is for preventing bodily harm or even death
and use should follow this safety rules.
SAFEGUARD INSTRUCTIONS
Please read the “Safety Rules” carefully before using this product. Following the safety rules
prevents users from damages related with the misuse of the product. It is very important to
follow these safety rules. We state “Caution” and “Warning” to clarify any potential risk for a
damage associated with the misuse of the product.
This information is for preventing damage or shorten the life
time of the products.
CAUTION
CAUTION
While stop driving (parking), set the car in motion.
- It may cause battery discharge.
Do not use multi socket or extended adaptor.
- It may cause unexpected heating, fire and malfunction.
Unplug product when do not use for a long time.
- It may case fire by short circuit due to heating.
Do not place near magnet.
- It may cause malfunction and trouble.
Should install while power off. (After install products, connect DC jack)
- It may cause to electronic shock or malfunction.
Do not push a LCD panel.
- It may cause LCD broken.
In case of inserting battery, attend to polarity and insert according to direction.
- When wrong inserting, it may cause fire, damage by explsion.
Before install the body, take enough place at least more than 15cm from the wall to
emit heat.
The battery for remote controller is not rechargeable and should replace same or simi-
lar model. Used battery may cause environmental pollution, so trash it carefully.
- This may cause a malfunction and problem.

4 5
WARNING
Do not get product wet and operate with wet hands.
- It may cause to electronic shock or malfunction.
Do not put the product in place where sudden temperature increasing and should use
on optimum voltage, temperature and humidity.
- It may cause to electronic shock or malfunction.
Do not place near of air bag effective range.
- It may cause malfunction of air bag or accident, injury due to hitting monitor by
air bag.
Do not pull cord with a jerk, should catch a plug and pull. Do not use damaged cord.
- It may cause cord malfunction, electronic shock and fire.
Keep clean dust on power socket.
- It may cause electronic shock and fire by bad connection.
Do not clean exterior with volatility or oily solvent.
Neither keep touching rubber and plastic for long time.
- It may cause change of surface, fall of paint, malfunction and fire.
When clean exterior, power off and wipe with dry cloth.
- Wet cloth may cause a electronic shock.
Do not place where vibration and shock.
- It may cause throw down and then malfunction and accident.
Do not put metals as like pin and needle into hole and chink of grill, speaker.
- In case of inserting them, stop to operate, it may cause electronic shock, fire and
malfunction.
Do not use in problem condition as like smoking, smell something burn.
- It may cause fire. Stop to use and make inquiries to agency.
Do not disassemble, repair and remodeling.
- It may cause malfunction and injury, can not get warranty.
- Make inquiries to agent for repair and checkup.
18”TFT LCD DIGITAL COLOR MONITOR
※ To safely use the product, please read the user’s manual carefully before use.
1) Connect all lines as directed in the product connection map in the manual.
2) Use the product at the temperature range of -10℃~ 60℃.
3) Screen may be a little dark when the product is operated in low temperature areas.
4) Screen will show normal luminosity after a few minutes.
5) When you install the product in a car, do not set a volume level too loud for others to hear
outside.
6) Quality of pictures on screen may vary depending on the radio field strength in different
locations.
7) You should use video equipment where you experience weak radio field strength.
8) Follow traffic laws when you use the Navigation Route System.
BEFORE USE
28”TFT LCD DIGITAL COLOR MONITOR
• Digital TFT Wide LCD with high resolution and low reflection
• All electronic control functions
• Convenient Graphic OSD
• All functions are displayed on screen (OSD function)
• Auto recognition function of TV signal system (PAL/ NTSC/ AUTO)
• PC auto adjustment
• 7 Languages on OSD menu (ENG-FRA-DEU-ESP-ITA-JPN-KOR)
• Auto mode selection (DSUB ANALOG, DVI DIGITAL, AV, S-VIDEO)
• One-touch Dimmer (Remote control)
• 0.5Watt speaker built-in
• STAND-BY function
• Low power consumption
SPECIAL FEATURES OF THE PRODUCT

6 7
38”TFT LCD DIGITAL COLOR MONITOR
TERMS OF PART 48”TFT LCD DIGITAL COLOR MONITOR REMOTE CONTROL
① POWER
② TV/AV
③ ▲▼CH
④ MENU
⑤ ◀▶VOL
⑥ PICTURE
⑦ SETUP
⑧ SOUND
⑨ MUTE
⑩ RECALL
⑪ AUTOPIC
⑫ SLEEP
⑬ CH.SET
⑭ A.MEMO
⑮ 0~9 KEY
Power On/Off
Select DSUB ANALOG/ EXTERNAL VIDEO/ S-VIDEO
Selects channel and moves to MENU
Selects menu and changes function
Controls Volume and changes MENU level
Picture selection button
Setup selection button
Sound selection button
For muting sound. Returns to the previous sound level when you push again
Displays present status and volume level
Selects DYNAMIC, NORMAL, MILD, USER for PICTURE
No use button
No use button
No use button
No use button
①
④
⑦
②
⑥
③
⑤
⑧
⑨
⑮
⑫
⑪
⑩
⑭
⑬
①④②⑥③ ⑤
① MODE
② MENU
③ DOWN
④ UP
⑤ POWER
⑥ Remote Sensor Window
AV/S-VIDEO/PC(RGB) selection function. Press the mode button to be
appeared source select OSD box and press the DOWN, UP button or
mode button repeatedly th press the menu button or wait 3 second to
select highlighted source.
* If PC picture size does not match with full horizontal or vertical screen
size, press the mode button continuously(2~3 second) and wait for a
little while then you can see the most appropriate screen.
Button to Setup Screen and Function.Press the menu button to be ap-
peared Menu OSD box and press the mode button repeatedly to select
the main menu(Picture menu, Setup menu, Audio menu), then press
the DOWN or UP button to enter to sub menu, press the mode button
repeatedly to highlight icon that user wants, press the DOWN, UP but-
ton to increase, decrease or change the function. Push the Menu button
once to return to the main menu to select another function or press
twice to exit from the OSD.
Select the sub menu, decrease the selected function, hot key for volume
down.
Select the sub menu, increase the selected function, hotkey for volume up.
Power On/O
Sensor for receiving signal from the remote control

8 9
58”TFT LCD DIGITAL COLOR MONITOR
* ( ), it means a remote control button.
FUNCTIONS
POWER ON/OFF
1
• POWER ON/OFF KEY
1) Push POWER(POWER) button. POWER is on.
2) Push POWER(POWER) button again. POWER is OFF.
MODE (TV/AV)
2
• It is function to change external video signals to DSUB ANALOG/ VIDEO/ S-VIDEO
* Adjust it with CH ▲▼
* Adjust it with MODE (Key button)
MENU (MENU)
3
• AV/ S-VIDEO
PICTURE(PICTURE)
- +
- +
- +
- +
- +
PICTURE
SETUP
BRIGHTNESS
CONTRAST
SHARPNESS
COLOR TINT
COLOR TONE
SYSTEM
55
40
14
50
60
AUTO NTSC PAL
1) BRIGHTNESS
2) CONTRAST
3) SHARPNESS
4) COLOR TINT
5) COLOR TONE
6) SYSTEM
Adjust the brightness of VIDEO without affecting DSUB ANALOG’s bright-
ness.
Adjust the contrast of VIDEO without aecting DSUB ANALOG’s contrast.
Adjust the sharpness of video image.
Change the richness of color.
Change the tone of color.
Change broadcast system NTSC, PAL, AUTO
* With VOL▶, go to SUB MENU. After adjusting in SUB MENU, press MENU to exit.
SETUP (SETUP)
▶ ENGLISH
- +
- +
- +
- +
▶ OFF
PICTURE
SETUP
SOUND
LANGUAGE
OSD TIME
TRANSLUCENT
OSD H POS.
OSD V POS.
FACTORY RESET
10
14
50
50
1) LANGUAGE
2) OSD TIME
3) TRANSLUCENT
4) OSD H POS.
5) OSD V POS.
6) FACTORY RESET
Change language English, French, German, Spanish, Italian, Japanese,
Korean.
The number of seconds that the OSD will remain visible before dis-
appearing.
Change the opaqueness of the background of the OSD.
Move the OSD Window to the horizontal direction.
Move the OSD Window to the vertical direction.
A factory default reset will clear all of OSD information.
* With VOL▶, go to SUB MENU. After adjusting in SUB MENU, press MENU to exit.
1) MUTE
2) VOLUME
3) TREBLE
4) BASS
Mute the sound temporarily. Mute is released when you change channel
and adjust volume.
Adjust the sound volume.
Emphasize high frequency audio.
Emphasize low frequency audio.
DSUB ANALOG/ AV/ S-VIDEO
DSUB ANALOG
AV
S-VIDEO
SOURCE
DSUB ANALOG/ DVI DIGITAL/ AV1/ AV2
DSUB ANALOG
AV1
AV2
SOURCE
SOUND (SOUND)
- +
- +
- +
PICTURE
SETUP
SOUND
MUTE
VOLUME
TREBLE
BASS
10
50
50
▶ OFF
* With VOL▶, go to SUB MENU. After adjusting in SUB MENU, press MENU to exit.
The audio input level should be met with the specification because of the audio
distorition.

10 11
* With VOL▶, go to SUB MENU. After adjusting in SUB MENU, press MENU to exit.
The color temperature could be changed based on the lcd specification.
• DSUB ANALOG
PICTURE
1) BRIGHTNESS
2) CONTRAST
3) H POSITION
4) V POSITION
5) PHASE
6) PIXEL FREQ.
Adjust the brightness of DSUB ANALOG without affecting AV/ S-VIDEO’s
brightness.
Adjust the contrast of DSUB ANALOG without aecting AV/ S-VIDEO’s con-
trast.
Adjust the horizontal position of the image.
Adjust the vertical position of the image.
Remove the noises. When phase value is wrong, the image has vertical
lines especially in 1 dot on and o.
Adjust the sampling frequency of DSUB analog signal.
* With VOL▶, go to SUB MENU. After adjusting in SUB MENU, press MENU to exit.
COLOR
1) 9300K
2) 7300K
3) 6500K
4) USER
Change color temperature : Red 42 Green 52 Blue 50
Change color temperature : Red 51 Green 46 Blue 46
Change color temperature : Red 40 Green 54 Blue 54
User customizable. (RED, GREEN, BLUE)
The tone of color can be changed from red-dish white to bluish white.
The individual color components are also user customizable.
PICTURE
COLOR
SETUP
9300K 7300K 6500K USER
RED
GREEN
BLUE
- +
- +
- +
50
50
50
- +
- +
- +
- +
- +
- +
PICTURE
COLOR
SETUP
SOUND
BRIGHTNESS
CONTRAST
H POSITION
V POSITION
PHASE
PIXEL FREQ.
75
50
50
50
14
100
DISPLAY MODES
For the display modes listed below, the screen image has been optimized during manu-
facture.
MODE
VGA
SVGA
800 x 600
800 x 600
37.880
46.875
60.300
75.000
40.000
49.500
720 x 400
640 x 480
640 x 480
31.469
31.469
37.500
70.087
59.940
75.000
28.322
25.175
31.500
Resolution Horizontal
Frequency(KHz)
Vertical
Frequency(Hz)
Pixel Clock
Frequency(MHz)
RECALL
4
AUTO PIC
5
TV/AV
6
Displays present status and volume level.
Select DYNAMIC, NORMAL, MILD, USER for PICTURE
Select DSUB ANALOG, EXTERNAL VIDEO, S-VIDEO
+ / +
+ / +
- / +
- / -
- / -
Sync Polarity
(H/V)
MUTE
7
• It is a function of Mute control. When you push MUTE button,
OSD display this image. This image can be toggle.
OUT OF RANGE 1) The screen shows this when signal is out of range.
2) The screen shows this when there is no signal.
3) The screen shows this when the signal cable is not
connected.
NO SIGNAL
CHECK CABLE
OSD MESSAGE
8

12 13
1. Choose a location where you install the Monitor. Clean the place for the Stand with cleanser
and remove the safeguard tape. And then attach it exactly where you want.
2. Fasten the Monitor with Tapping Screw.
3. Adjust angle of Stand and install Monitor.
4. Connect each connecting cable as in the product installation reference.
68”TFT LCD DIGITAL COLOR MONITOR
CONNECTIONS

14 15
• CM-800D
88”TFT LCD DIGITAL COLOR MONITOR
SPECIFICATIONS
ITEM
LCD PANEL BRIGHTNESS
CONTRAST RATIO
VIEW ANGLE CR≥10
360 cd/m2
500:1
70/ 65/ 70 (H/U/D)
SIZE
NUMBER OF PIXELS
DOT PITCH
20.32 cm (8.0inch)
800 x 600
0.2025(W) x 0.2025(H) mm
SPECIFICATION
INPUT
SIGNAL
VIDEO
Composite Video, S-VIDEO (75 ohm 1Vp-p)
ANALOG R.G.B 0.7Vp-p
FRE-
QUENCY
15.73 KHz
60 Hz
HORIZONTAL
VERTICAL
USER CONTROLS POWER ON/OFF, MENU, MODE, PRO UP/DOWN
DIMENSION (W x H x D) 223(W) x 178(H) x 34.5(D) mm
-10℃ ~ 60℃OPERATING TEMPERATURE
STORAGE TEMPERATURE -20℃~ 70℃
1.2 kg (Exclude Monitor Bracket)
WEIGHT
※ Design and specications could be changed without notices.
MONO INPUT 400mVrms
AUDIO
POWER
SUPPLY
DC 12V
10 Watt AT DC 12V
VOLTAGE
CONSUMPTION
NTSC/ PAL/ AUTOINPUT SYSTEM
7 LanguagesOSD DISPLAY
TTL Separate, CompositeINPUT SYNCHRONOUS
SOUND SIGNAL 0.5 Watt max
78”TFT LCD DIGITAL COLOR MONITOR
CHANGING REMOTE CONTROL BATTERY
1) Slide and open the battery cover.
2) Insert new battery and ensure that the polarities
are correct when inserting. (No. CR2025)
3) Slide and close the battery cover.