Camos CWM-500 User manual

INSTRUCTION MANUAL
CWM-500
5”WATERPROOF MONITOR
Thank you for purchasing this product.
For proper usages and application,
Please read this instruction manual thoroughly.
PRINTED IN KOREA ver. 1.0 * Design and specifications are subject to change without notice.

2
CONTENTS
SAFEGUARD INSTRUCTIONS
FEATURE
BOX CONTENTS
FUNCTION OF EACH PART
FUNCTION
SETTING
INSTALLATION and CONNECTION
SPECIFICATION
....................................... 3
............................................................................. 5
................................................................ 5
............................................ 6
......................................................................... 7
............................................................................. 9
.......................... 11
............................................................. 13

3
5”WATERPROOF MONITOR
SAFEGUARD INSTRUCTIONS
Please read the “Safety Rules” carefully before using this product. Following the safety rules pre-
vents users from damages related with the misuse of the product. It is very important to follow
these safety rules. We state “Caution” and “Warning” to clarify any potential risk for a damage
associated with the misuse of the product.
WARNING
This information is for preventing bodily harm or even death and
use should follow this safety rules.
This information is for preventing damage or shorten the life time
of the products.
This information is for user’s reference for better usability.
CAUTION
NOTICE
CAUTION
While stop driving (parking), set the car in motion.
- It may cause battery discharge.
Do not use multi socket or extended adaptor.
- It may cause unexpected heating, re and malfunction.
Unplug product when do not use for a long time.
- It may case re by short circuit due to heating.
Do not place near magnet.
- It may cause malfunction and trouble.
Should install while power o. (After install products, connect DC jack)
- It may cause to electronic shock or malfunction.
Before install the body, take enough place at least more than 15cm from the wall to
emit heat.

4
WARNING
Do not put the product in place where sudden temperature increasing and should use
on optimum voltage, temperature and humidity.
- It may cause to electronic shock or malfunction.
Do not place near of air bag eective range.
- It may cause malfunction of air bag or accident, injury due to hitting monitor by
air bag.
Do not pull cord with a jerk, should catch a plug and pull. Do not use damaged cord.
- It may cause cord malfunction, electronic shock and re.
Keep clean dust on power socket.
- It may cause electronic shock and re by bad connection.
Do not clean exterior with volatility or oily solvent.
Neither keep touching rubber and plastic for long time.
- It may cause change of surface, fall of paint, malfunction and re.
When clean exterior, power o and wipe with dry cloth.
- Wet cloth may cause a electronic shock.
Do not place where vibration and shock.
- It may cause throw down and then malfunction and accident.
Do not put a pin or needle on the hole or crack in the body.
- In case of inserting them, stop to operate, it may cause electronic shock, re and
malfunction.
Do not use in problem condition as like smoking, smell something burn.
- It may cause re. Stop to use and make inquiries to agency.
Do not disassemble, repair and remodeling.
- It may cause malfunction and injury, can not get warranty.
- Make inquiries to agent for repair and checkup.
When the power cable cord touches a metal case, cover it with a friction tape.
- Short circuit or disconnection of wire may cause a re or accident.
Do not use bolts or nuts from a parts for vehicle.
- Using bolt or nuts from steering column or break may cause an accident.
After installing, check it break lamp, head lamp and wipe works properly.

1
2
* Design and Specications are subject to change without notice.
Stand(CL-5)
U-Bracket
(Optional)
TRG Extension
Cable(x3)
Accessory Pack
5
5”WATERPROOF MONITOR
5”WATERPROOF MONITOR
• Water Resistant (IP-67), Aluminum housing
• Application of TFT LCD with high resolution and low reflection
• All functions are displayed on screen (OSD function)
• PWM volume control
• Mode selection function (3 Mode)
• Low energy consuming rate
• Language Display Selection (ENG-DEU-ITA-FRA-SPA-KOR-JPN)
• Free voltage (From DC 12V to DC24V)
FEATURE
BOX CONTENTS
• Before use this products, please check below contents. If there is something missing parts,
please contact sales agent.
Cigar CableMonitor Monitor Cable
Sun Visor
Stand
(CL-9, Optional)
Instruction
Manual

3
1. LCD SCREEN
2. STAND BY LED
3. BUTTONS
4. SUN VISOR HOLE
5. SPEAKER HOLE
6. STAND BRACKET
QVGA (320x234)
Stand by lamp
DIMMER, LEFT, RIGHT, MODE, MENU, POWER
Sun Visor installation hole
Speaker hole (Waterproof)
Stand x Bracket
6
5”WATERPROOF MONITOR
FUNCTION OF EACH PART

4
CAM1 CAM2 CAM3
DIMMER DIMMER
7
5”WATERPROOF MONITOR
FUNCTIONS
POWER ON / OFF
1
1. Press POWER button for power ON. (Stand-by LED is OFF)
2. Press POWER button again for power OFF. (Stand-by LED is ON)
MODE
2
1. Press MODE button.
2. CAM1 - CAM2 - CAM3 - CAM1 appears on the screen.
3. it is disappeared after 3 sec.
VOLUME CONTROL
3
1. Press LEFT/RIGHT button.
2. The monitor shows volume on the screen and
volume is UP/DOWN. (0~100)
VOLUME 30
DIMMER
4
BRIGHTNESS DARKNESS

8
Screen switch while trigger input
5
What is <Trigger input> or <Trigger signal>? We call it when a circuit works by a signal for
example if driver uses right/left turn signal or reverse gear, the monitor shows connected
camera screen on driving mode.
1) If there is trigger signal input, the connected screen (Trigger input screen) is displayed and
the screen goes former one when the signal is disappeared.
* Below example is set with TRG1(Left signal light)=CAM1 / TRG2(Right signal light)=CAM2 /
TRG3(Rear light)=CAM3.
CAM3 CAM1
2) In case of light on emergency blinker(TRG1+TRG2), the monitor displays CAM3. And the
screen goes former one when the signal(light on emergency blinker) is disappeared.
The example is set with TRG1(Left signal light=CAM1 /TRG2(Right signal
light)=CAM2 / TRG3(Rear light)=CAM3.
NOTICE
CAM1 CAM3
Current screen
ex. CAM3(Rear view)
Connected screen
by the trigger line
Current screen
ex. CAM1(Left view)
Rear view camera screen(CAM3)
with the emergency light

5
DIMMER
LANGUAGE
DIRECTION
RESET
ENGLISH
0˚
CONTRAST
BRIGHTNESS
COLOR
TINT
70
40
40
40
CAM1 NORMAL
DIMMER
LANGUAGE
DIRECTION
RESET
ENGLISH
0˚
DIMMER
LANGUAGE
DIRECTION
RESET
ENGLISH
0˚
DIMMER
LANGUAGE
DIRECTION
RESET
ENGLISH
0˚
DIMMER
LANGUAGE
DIRECTION
RESET
ENGLISH
180˚
2. Use MODE button to select SUB MENU and then use LEFT/RIGHT button to adjust.
- RESET : Reset will have the monitor with the factory default value.
9
1. Use MENU button to change MAIN MENU (SETUP - PICTURE - CAMERA)
5”WATERPROOF MONITOR
SETTING
ENGLISH DEUTSCH ITALIANO FRANCAIS
ESPAnOL
SETUP
- DIMMER
- LANGUAGE
- DIRECTION
SELECT
SUB MENU
ADJUST
SELECT
SUB MENU
ADJUST

10
PICTURE
CAMERA
CONTRAST
BRIGHTNESS
COLOR
TINT
70
40
40
40
CAM1 NORMAL CAM1 MIRROR
Connected camera NORMAL / MIRROR selecting function
In CAM2(or CAM3) Mode, CAM2(or CAM3) NORMAL/MIRROR is adjusted.
1. Use MODE button to select CONTRAST, BRIGHTNESS,
COLOR, TINT menu.
(Selected menu is in red.)
2. Press LEFT/RIGHT button to adjust the number.

6
Double side
adhesive tape Double side
adhesive tape
Double side
adhesive tape
Double side adhesive tape
Screw hole
Sun Visor should be installed with 4 screws.
11
INSTALLATION
5”WATERPROOF MONITOR
INSTALLATION and CONNECTION

12
CAMERA 1 (LEFT)
CAMERA 2 (RIGHT)
CAMERA 3 (REAR)
DC 12V ~ 24V
GREEN (STAND BY1 / LEFT)
ORANGE (STAND BY2 / RIGHT)
BLACK (STAND BY3 / REAR)
CAMERA(OPTION)
CIGAR CABLE
CONNECTION

75”WATERPROOF MONITOR
SPECIFICATION
5 inch
QVGA (320x234)
400cd/m²
400:1
70˚ / 70˚ / 40˚ / 60˚
DC 12V ~ 24V
450mA (DC 12V, monitor set only)
NTSC / PAL
H : 15.734 kHz / V : 60 Hz
H : 15.625 kHz / V : 50 Hz
Composite Video 1Vp-p (75 ohm)
MONO INPUT 400 mVrms
0.5 Watt max.
7 languages
-10˚C ~ 60˚C
-20˚C ~ 70˚C
152(W) x 119(H) x 27(D) mm (Monitor Only)
620g (Monitor only)
Screen size
Resolution
Brightness
Contrast ratio
View angle(L/R/U/D)
Voltage
Current
NTSC
PAL
Video Signal
Audio Signal
Input System
Speaker
Language display selection
Operating temperature
Storage temperature
Dimension
Weight
LCD Panel
Power Supply
Frequency
Input Signal
In case of starting usage on low temperature than working temperature, the
screen may blink for a while (2~5 minute). Please wait about 10 minutes and
try to power on again.
NOTICE

MEMO

MEMO

INSTRUCTION MANUAL
Table of contents
Other Camos Monitor manuals

Camos
Camos CM-840D User manual

Camos
Camos CM-800D User manual

Camos
Camos MM-800 User manual

Camos
Camos CM-709M2 User manual

Camos
Camos MM-1750H User manual

Camos
Camos CNT-701 User manual

Camos
Camos CM-840D User manual

Camos
Camos cm-703 User manual

Camos
Camos CM-1710D User manual

Camos
Camos MM-1510D User manual