Camos CNT-701 User manual

OWNER’S MANUAL
MOTORIZED 7” WIDE
TFT LCD COLOR MONITOR
CNT-701
PW

ANY CHANGES OR MODIFICATIONS IN
ANY CHANGES OR MODIFICATIONS IN
CONSTRUCTION OF THIS UNIT DEVICE WHICH
CONSTRUCTION OF THIS UNIT DEVICE WHICH
IS NOT APPROVED BY THE PARTY RESPONSIBLE
IS NOT APPROVED BY THE PARTY RESPONSIBLE
FOR COMPLIACE COULD VOID THE USER’S
FOR COMPLIACE COULD VOID THE USER’S
AUTHORITY TO OPERATE THE EQUIPMENT.
AUTHORITY TO OPERATE THE EQUIPMENT.
! WARNING
! WARNING
DO NOT WATCH MONITOR WHILE DRIVING
DO NOT WATCH MONITOR WHILE DRIVING

WARNING
The WARNING mark is intended to alert the user to the important operating instructions.
Wrong operations will result in severe injury to the unit.
DO NOT WATCH MONITOR WHILE DRIVING
Watching the video while driving may interrupt driving and may cause an accident.
DO NOT OPERATE ANY FUNCTION THAT TAKE YOUR ATTENTION AWAY FROM DRIVING YOUR VEHICLE
Operation of some functions for this unit is very complicated. It is necessary to put these
functions in to a special MENU screen. These will restrict operation of these functions only
vehicle is parked. This is to make driver’s attention to the road and not to this unit.
Any function that requires driver’s attention for a long time should be performed only after you
stop the car. Always stop the car in a safe place before performing these functions.
Performing these functions while driving may result in a serious accident.
DO NOT DISASSEMBLE
Attempts to disassemble may lead to an accident, re and / or an electric shock.
KEEP SMALL ARTICLES OUT OF REACH OR CHILDREN
Keep small things (screws etc.) in places not accessible to children. If swallowed, consult a
physician immediately.
FUSE REPLACEMENT
When replacing the fuses, the replacement must be the same amperage as shown on the
fuse holder. If the fuse(s) blow more than once, carefully check all electrical connections for
short circuit, also have your vehicle’s voltage regulator checked.
DO NOT USE IMMEDIATELY IF A PROBLEM APPEARS
When a problem appears, stop using the system immediately and contact the dealer from
whom you purchased the equipment.
DO NOT USE THIS EQUIPMENT OUTSIDE THE VEHICLE
Do not use this equipment for purpose other than those listed for a vehicle.
Failure to do so may result in an electric shock or an injury.
TEMPERATURE
Be sure the temperature inside the vehicle is between +60 (+140 ) and -5 (+23 ) before
turning your unit on.
MAINTENANCE
If you have problem, do not attempt to repair the unit by yourself. Return it to your dealer who
you purchased it from.
INSTALLATION LOCATION
Make sure the unit will not be exposed to : Direct sun & heat, High humidity, Excessive dust,
Excessive vibration.
3
CAUTION

CONTENTS
……………………………………………………………
………………………………………………………………
……………………………………………………………
……………………………………………………………
……………………………………………………………
…………………………………………………………………
……………………………………………………
……………………………………………………………
………………………………………………………
………………………………………………
………………………………………………
……………………………………………
…………………………………………
……………………
………………………………………………………
……………………………………………
……………………………………………………
……………………………………………………
……………………………………………………………
………………………………………………………………………
………………………………………………
……………………………………………………
….......………………………………………………
……………………………………………
…………………………………………………………
…………………………………………………………………
5
5
5
6
6
7
8
9
9
9
9
9
10
10
10
11
11
11
11
12
12
12
13
14
15
16
4
Contents
GETTING STARTED
FEATURES
ACCESSORIES
CONNECTION
INSTALLATION
MONITOR
REMOTE CONTROL
BASIC OPERATION
POWER ON / OFF
OPENING THE MONITOR
CLOSING THE MONITOR
ADJUSTING TILT POSITION
ADJUSTING MOVE POSITON
ADJUSTING LEFT/RIGHT VIEWING POSITION
SELECTING MODE
SETTING THE CAMERA IN
WARNING SCREEN
ADJUSTING VOLUME
AUDIO MUTE
FUNCTION
SELECTING THE MENU
PICTURE CONTROL
AUDIO CONTROL
MENU SETTING CONTROL
TROUBLE SHOOTING
SPECIFICATION

FEATURES
5
GettingStarted
ACCESSORIES
7" wide high resolution TFT active matrix display
3.
Power cable with lter box ass’y
5.Mounting bracket & ETC
Remote control &
Lithium battery CR2025
A lithium battery is pre-installed in
the Remote Control Unit (with
insulation sheet).
To use the Remote Control Unit,
remove the insulation sheet as shown.
PULL OUT
Slim size (1/2 DIN) design
NTSC/PAL compatible
Built-in FM transmitter
2 Video input / 1 Video output
1. Speaker
MODE
NAVI
IN UP
DN
OUT
ASPECT C
A
B
TILT TILT
MUTE OPEN
CH
MENU
M CH+
SCAN
M CH-
A/M
VOL
VOL
CH
2.
4.Mounting & Screws
7. SD Card
SPK-L
SPK-R
6.GPS
3M tape
8. Manual
2x Double side
adhesive tape
Insulation
sheet

GettingStarted
Connection
Installation
RED
RED
PINK - ILLUMINATION
ORANGE - REVERSE GEAR SENS
BROWN - REVERSE GEAR SENS
BLACK
YELLOW
RS-232/TMC
GPS
RED
AVIN-R
AVIN-L
AVIN-V
WHITE
WHITE
YELLOW
YELLOW
To VIDEO INPUT
To VIDEO OUTPUT
To REAR VIEW CAMERA VIDEO INPUT
To AUDIO INPUT (R)
SPK-L
SPK-R
To AUDIO OUTPUT (R)
To AUDIO OUTPUT (L)
To AUDIO INPUT (L)
YELLOW
PW
PW

MONITOR
7
PW
No.
Mode Button
Open / Close Button
Tilt Up / Down Button
Mute Button
Cursor Up / Down
Cursor Left / Right , Volume Up / Down Button
Remote sensor
Short Key
Function
Long Key
Power Button
Move Up / Down Button
Menu Button
GettingStarted
8
8SD-Card Reader

8
Power
Mode
Volume Up / Down , Cursor Left / Right
Tilt In / Out
Mute
Menu
Cusor Up / Down
Tilt Up / Down
Open
Remote Control replacing battery
1
2
Opening the battery cover.
The remote control will work within the range of about
30 degrees and 3 meter distances.
Notes
Do not expose the remote sensor to
direct sunlight or lighting apparatuses.
Doing so may cause a malfunction.
PULL OUT
PUSH
Replacing a new battery as shown.
( Use CR2025 lithium battery. )
3
Closing the cover.
CR2025
3V
CR2025
3V
The operation range of the remote control
PW
GettingStarted
REMOTE CONTROL
IN
IN
1
1
4
4
5
5
6
6
2
2
3
3
UP
UP
DN
DN
OUT
OUT
A
A
OPEN
OPEN
TILT
TILT
TILT
TILT
CH
CH
MENU
MENU
MUTE
MUTE
SCAN
SCAN
INFO
INFO
MODE
MODE
VOL
VOL
VOL
VOL
CH
CH

1. POWER ON
Press any button on the unit or
Power Button of the remote control to turn the
power on. The monitor is automatically opened. When REVERSE wire is connected
to the signal output (12V) of the reverse gear, the monitor is automatically opened
and the mode is set to RVC
2. POWER OFF
Press the
Power Button on the unit more than 1 second or the remote controller again
to turn the power o. And the monitor is automatically closed. If the car key is pulled
out, the monitor will be closed automatically.
Press any button, the monitor will be opened.
Press
Open/Close Button on the unit. The monitor will be closed or opened. If it is
not closed, hold left and right upper side of the monitor and make the monitor parallel
with the unit as the picture.
The tilt position can be adjusted in 8 steps by pressing Tilt Up/Down Button . Each
time you press Tilt Up/Down Button the monitor will swing one step backward or
forward.
If the monitor is not paralled to the front of the unit, the monitor
will not be closed.
9
60°
110°
BasicOperation
POWER ON / OFF
OPENING THE MONITOR
CLOSING THE MONITOR
ADJUSTING TILT POSITION

The move position can be adjusted in 4 steps by pressing more than 2 sec Tilt Up /
Down Button or Tilt In / Out Button of the remote controller.
If the monitor is not parallel to the front of the unit, the MOVE
function is not operated. You can hear fast beep tone, when you
operate the mechanism under abnormal conditions (Minimum,
Maximum, crooked angle of the front panel).
The monitor’s left / right position can be adjusted for easier viewing by hand as the
picture below.
Press Mode Button to select the desired mode. Each time you press this button, the
mode changes as follows.
If the REVERSE wire is connected to power output of the
reverse gear, the mode will be automatically changed to RVC
when the gear is positioned to REVERSE.
AV1 AV2 RVC
10
7mm
7mm
BasicOperation
ADJUSTING MOVE POSITION
ADJUSTING LEFT / RIGHT VIEWING POSITION
SELECTING MODE

When you install a rear view camera, you must connect a rear view camera to RVC. If you put the
gear lever to R (Reverse) to move your car backward, the rear view camera video will be displayed
on the screen through the RVC mode.
The monitor shows the following warning picture when parking brake is not pulled or while driving
to prevent trac accident that may happen while watching the screen. The monitor shows the
warning picture only and does not operate menu control.
Press the Volume Up / Down Button to adjust the volume level.
Press the Mute Button to mute the audio. Press the mute button or any button again to return to
the previous audio level.
11
WARNING SCREEN
SETTING THE CAMERA IN
ADJUSTING VOLUME
AUDIO MUTE
BasicOperation

You can select the menu to make this unit or VIDEO sources connected to this unit in
the best conditions.
1. Press
Menu Button to select desired menu. Each time you press Menu Button , the
menu changes as follows.
2. Press
Cursor Up / Down Button to select the item that you want to adjust.
The background color of the selected item changes to yellow.
3. Press
Cursor Left / Right Button to adjust the selected item.
PICTURE SETTING MENU OFF AUDIO
Press Menu Button to show PICTURE on the screen.
Press
Cursor Up / Down Button to select the desired item.
Press
Cursor Left / Right Button to change the item’s value or level.
: Adjusting for brightness of the screen.
: Adjusting for contrast level of the picture.
: Adjusting for clear-cut level of the picture.
: Adjusting for the depth of color.
: Adjusting for the tone of color.
: The brightness of this unit will be changed depending on the
brightness of the environment.
Dimmer mode will be toggled as follows
1. BRIGHTNESS
2. CONTRAST
3. SHARPNESS
4. COLOR
5. TINT
6. DIMMER
: The brightness level is set to 50. (Default set)
: The brightness level is set to 70.
: The brightness level is set to 40.
: It is automatically changed between DAY and NIGHT
depending on the brightness of the environment.
: The brightness level is set to a user’s set level.
STANDARD
DAY
NIGHT
AUTO
USER
STANDARD DAY NIGHT AUTO USER
The MENU is automatically disappeared about 10 seconds after it appears on the screen.
The appeared time is also adjusted in MENU SETTING page.
The MENU button is used for memorizing each re-adjusted level.
If you change the BRIGHTNESS level, DIMMER value will be changed USER mode
automatically.
If the illumination wire is connected to the tail lamp and you turn on the tail lamp in your
car, the brightness level is automatically set to 40 degree (AUTO mode only)
12
Function
SELECTING THE MENU
PICTURE CONTROL
MENU SETTING
DISPLAY MODE 16:9
TV SYSTEM NTSC
OSD TIMEOUT 10
TRANSPARENCY 80
LANGUAGE ENGLISH
VIDEO3 MIRROR 0
FACTORY RESET
AV1
PICTURE
CONTRAST 50
17
50
50
BRIGHTNESS 50
SHARPNESS
COLOR
TINT
DIMMER STANDARD
SCREEN FLIP
AV1
AUDIO
FM OUTPUT OFF
VOLUME 40
AV1

: Each time you press SCREEN FLIP button, screen display will be changed
ip mode and normal mode. The FLIP screen will be useful when this unit is
installed in reversed mode as follows (FLIP mode: 180° rotated image)
7. SCREEN FLIP
For memorizing re-adjusting value, press Menu Button and exit PICTURE page.
Press Menu Button repeatedly to show TV & AUDIO on the screen.
Press Cursor Up / Down Button to select the desired item.
Press Cursor Left / Right Button to change the item’s value or level.
: Adjusting for audio volume
The volume level is indicated in the monitor from 0(min) to 50(max).
: Transfer a wireless audio signal to your car stereo.
The selectable frequencies are from 87.9MHz to 90.9MHz with 0.2MHz span.
Set the frequency to the less interfered point or your car stereo.
1. VOLUME
2. FM OUTPUT
13
PW
Function
AUDIO CONTROL

Even if VIDEO3 MIRROR mode is set to 180 and input mode selected to RVC, screen
will be changed to normal display mode when enter the MENU pages.
Press Menu Button repeatedly to show MENU SETTING on the screen.
Press Cursor Up / Down Button to select the desired item.
Press Cursor Left / Right Button to change the item’s value or level.
: TV output type select (AUTO, PAL, NTSC)
: The picture is shown as 4:3 or 16:9 sized screen.
: The OSD TIMEOUT can be adjusted from 5SEC ~ No time out.
“00” value is no time out. The default set is 10 seconds.
: It is adjusted from 00 ~ 100 and the background transparency is adjusted.
: The OSD language is selectable.
(ENGLISH / KOREAN
: Each time you press this button, VIDEO3 MIRROR mode will be changed
as follows.
When you set VIDEO3 MIRROR 180 and input mode selected to RVC,
the screen will be show mirror looking image. It is useful when a rear view
camera is connected to RVC input.
1. TV SYSTEM
2. DISPLAY MODE
3. OSD TIMEOUT
4. TRANSPARENCY
5. LANGUAGE
6. VIDEO3 MIRROR
14
180 0
For memorizing re-adjusting value, press MENU button and exit MENU SETTING page.
TV &AUDIO related menu setting values are remains the previous setting value.
: When you press this button, following menu setting values are reset to
factory default condition.
BRIGHTNESS
CONTRAST
SHARPNESS
COLOR
TINT
DIMMER
PICTURE CONTROL
50
50
17
50
50
STANDARD
TV SYSTEM
DISPLAY MODE
OSD TIMEOUT
TRANSPARENCY
LANGUAGE
VIDEO3 MIRROR
MENU SETTING CONTROL
NTSC
16 : 9
10
40
ENGLISH
0
VOLUME
FM OUTPUT
AUDIO CONTROL
40
OFF
7. FACTORY RESET
Function
MENU SETTING CONTROL

● Replace with a fuse of the same amperage. If the
fuse blow again, consult installation shop where
you purchased it from.
● Consult installation shop where you purchased it
from.
● Fuse is blown
● Incorrect wiring
Power does not turn on. (No sound is produced)
Power it o and power it on again. If it is not working,
consult installation shop where you purchased it from.
The microprocessor has
malfunctioned due to noise,
etc.
Nothing happens when buttons are pressed. Display is not accurate.
● When direct rays of the sun fall on the light-
receptive part of the remote controller, it may not
work.
● Check the battery of the remote controller unit.
● Direct rays of the sun fall
on the light-receptive part
of the remote controller
● The battery of the remote
controller unit is dead or
there is no battery in the
remote controller unit
The Remote controller does not work.
Check the parking brake is applied.The parking brake is not
pulled or the parking brake
wire is not connected.
Warning screen is displayed.
● Adjust the brightness properly.
● The temperature inside the vehicle may be 0
degree or less. Set to an appropriate temperature
(25 degree or so) and check it again.
● The display is may dark at night to prevent the
glare (When the headlight of the vehicle is lit in the
daytime, the display gets dark).
● The brightness control
is too low.
● The operating condition
is not good.
● The headlight of the
vehicle is lit.
The display is dark.
Check that Contrast and Color are adjusted properly.
The color is not adjusted
adequately
The color of the display is light or a shade of color is not good.
Set the NTSC / PAL properly according to video
source.
Improper NTSC / PAL
setting.
When video source is connected, the image is disturbed.
GENERAL
MONITOR

GENERAL
Power Supply
Power Consumption
Operating Temperature
Video Input signal
Video output signal
Dimension (W × H × D)
Polarity
Weight
Net
Gross
Screen size
LCD Type
LCD Drive system
Number of Pixels
Eective Pixels
Back Lighting
Color system
DC 14V ( 11V ~ 15V )
1.5 A
-10℃~ +60℃
1.0 Vpp / 75Ω
1.0 Vpp / 75Ω
178 × 25 × 189 mm
Negative Ground
1.7Kg
2.2Kg
MONITOR SECTION
※ Specifications are subject to be changed without notice.
7 Inch Wide
Transparent type TN LCD
TFT Active matrix
336,960 ( 1,440 x 234 )
99 % or more
U-shaped cold cathode Fluorescent Tube
NTSC / PAL