Campbell 05103 User manual

05103, 05106, and 05305
R.M. Young Wind Monitors
Revision: 8/07
Copyright © 1984-2007
Campbell Scientific, Inc.

Warranty and Assistance
The 05103, 05106, and 05305 R.M. YOUNG WIND MONITORS are
warranted by CAMPBELL SCIENTIFIC, INC. to be free from defects in
materials and workmanship under normal use and service for twelve (12)
months from date of shipment unless specified otherwise. Batteries have no
warranty. CAMPBELL SCIENTIFIC, INC.'s obligation under this warranty is
limited to repairing or replacing (at CAMPBELL SCIENTIFIC, INC.'s option)
defective products. The customer shall assume all costs of removing,
reinstalling, and shipping defective products to CAMPBELL SCIENTIFIC,
INC. CAMPBELL SCIENTIFIC, INC. will return such products by surface
carrier prepaid. This warranty shall not apply to any CAMPBELL
SCIENTIFIC, INC. products which have been subjected to modification,
misuse, neglect, accidents of nature, or shipping damage. This warranty is in
lieu of all other warranties, expressed or implied, including warranties of
merchantability or fitness for a particular purpose. CAMPBELL SCIENTIFIC,
INC. is not liable for special, indirect, incidental, or consequential damages.
Products may not be returned without prior authorization. The following
contact information is for US and International customers residing in countries
served by Campbell Scientific, Inc. directly. Affiliate companies handle
repairs for customers within their territories. Please visit
www.campbellsci.com to determine which Campbell Scientific company
serves your country. To obtain a Returned Materials Authorization (RMA),
contact CAMPBELL SCIENTIFIC, INC., phone [phone]. After an
applications engineer determines the nature of the problem, an RMA number
will be issued. Please write this number clearly on the outside of the shipping
container. CAMPBELL SCIENTIFIC's shipping address is:
CAMPBELL SCIENTIFIC, INC.
RMA#_____
815 West 1800 North
Logan, Utah 84321-1784
CAMPBELL SCIENTIFIC, INC. does not accept collect calls.

05103, 05106, 05305 Table of Contents
PDF viewers note: These page numbers refer to the printed version of this document. Use
the Adobe Acrobat® bookmarks tab for links to specific sections.
1. General Description.....................................................1
2. Specifications ..............................................................1
3. Installation....................................................................3
3.1 Siting.........................................................................................................3
3.2 Assembly and Mounting...........................................................................3
4. Wiring............................................................................5
5. Example Programs......................................................6
5.1 Wind Speed ..............................................................................................6
5.2 Wind Direction.........................................................................................6
5.3 Wind Vector Processing Instruction.........................................................7
5.4 Example Programs....................................................................................7
5.4.1 CR1000 Example Program .............................................................8
5.4.2 CR10X Example Program ..............................................................8
5.5 Long Lead Lengths...................................................................................9
6. Sensor Maintenance..................................................10
7. Troubleshooting ........................................................10
7.1 Wind Direction.......................................................................................10
7.2 Wind Speed ............................................................................................11
8. References .................................................................11
Appendices
A. Wind Direction Sensor Orientation........................A-1
A.1 Determining Truth North and Sensor Orientation .............................. A-1
i

05103, 05106, 05305 Table of Contents
B. Wind Direction Measurement Theory....................B-1
B.1 BRHalf Instruction.............................................................................. B-1
B.2 EX-DEL-SE (P4) Instruction .............................................................. B-1
Figures
3-1. Wind Monitor Mounted to the 019ALU Crossarm ................................ 4
3-2. Wind Monitor Mounted to a CM200 Series Crossarm
with PN 17953 Nu-Rail....................................................................... 4
3-3. Wind Monitor Mounted to a CM200 Series Crossarm
with CM220 Right Angle Mounting Kit............................................. 5
A-1. Magnetic Declination for the Contiguous United States ...................A-2
A-2. Declination Angles East of True North are Subtracted From 0 to
Get True North................................................................................A-2
A-3. Declination Angles West of True North are Added to 0 to
Get True North................................................................................A-3
B-1. 05103 Potentiometer in a Half Bridge Circuit ................................... B-1
Tables
1-1. Recommended Lead Lengths ................................................................. 1
4-1. Connections to Campbell Scientific Dataloggers................................... 5
5-1. Wind Speed Multiplier (with Configuration Code 21)........................... 6
5-2. Parameters for Wind Direction............................................................... 7
5-3. Wiring for Example Programs................................................................ 7
ii

05103, 05106, and 05305 R.M. Young
Wind Monitors
1. General Description
The 05103, 05106, and 05305 Wind Monitor sensors are used to measure
horizontal wind speed and direction. The 05305 is a high performance version
of the 05103 designed to meet PSD specifications for air quality applications.
The 05106 is recommended for marine applications.
Wind speed is measured with a helicoid-shaped, four-blade propeller. Rotation
of the propeller produces an AC sine wave signal with frequency proportional
to wind speed.
Vane position is transmitted by a 10K ohm potentiometer. With a precision
excitation voltage applied, the output voltage is proportional to wind direction.
The R.M. Young Instruction Manual includes additional information on the
operating principles, installation and maintenance of the sensor.
Lead length for the Wind Monitor is specified when the sensor is ordered.
Table 1-1 gives the recommended lead length for mounting the sensor at the
top of the tripod/tower with a 019ALU or CM200 series crossarm.
TABLE 1-1. Recommended Lead Lengths
CM6 CM10 CM110 CM115 CM120 UT10 UT20 UT30
10’ 13’ 13’ 19’ 24’ 13’ 24’ 34’
The 05103 / 05106 / 05305 ships with:
(1) Allen wrench from mfg
(1) Bearing spacer from mfg
(1) Calibration Sheet
(1) Instruction Manual
(1) 3659 Mounting pipe
2. Specifications
05103 and 05106 05305
Wind Speed
Range: 0-134 mph (0-60 m s-1) 0-90 mph (0-40 m s-1)
Accuracy: ±0.6 mph (±0.3 m s-1) ±0.4 mph (±0.2 m s-1)
Starting threshold: 2.2 mph (1.0 m s-1) 05103;
2.4 mph (1.1 m s-1) 05106 0.9 mph (0.4 m s-1)
Gust survival: 220 mph (100 m s-1) 100 mph (45 m s-1)
Distance constant
(63% recovery): 8.9 ft (2.7 m) 6.9 ft (2.1 m)
1

05103, 05106, and 05305 R.M. Young Wind Monitors
05103 and 05106 05305
Output: ac voltage (3 pulses per
revolution). 1800 rpm
(90 Hz) = 19.7 mph
(8.8 m s-1)
ac voltage (3 pulses per
revolution) 1800 rpm
(90 Hz) = 20.6 mph
(9.2 m s-1)
Wind Direction
Range: 0-360° mechanical,
355° electrical (5° open) Same
Accuracy: ±3° ±3°
Starting threshold
at 10° displacement: 2.2 mph (1.1 m s-1)
1.0 mph (0.5 m s-1)
Delay distance
(50% recovery): 4.3 ft (1.3 m) 3.9 ft (1.2 m)
Damping ratio: 0.25 0.45
Damped natural
wavelength: 24.3 ft (7.4 m) 16.1 ft (4.9 m)
Undamped natural
wavelength: 23.6 ft (7.2 m) 14.4 ft (4.4 m)
Output: Analog dc voltage from
potentiometer – resistance
10 kΩ, linearity 0.25%,
life expectancy 50 million
revolutions.
Same
Power Switched excitation
voltage supplied
by the datalogger.
Same
Physical
Operating
Temperature
-50° to +50°C, assuming
non-riming conditions
-50° to +50°C, assuming
non-riming conditions
Dimensions
Overall: 14.6” H x 21.7” L
(37 cm x 55 cm) 15.0” H x 25.6“ L (38 cm x 65 cm)
Main housing
Diameter: 2.0“ (5 cm) Same
Propeller Diameter: 7.1” (18 cm) 7.9” (20 cm)
Mounting Pipe: 1.34” (34 mm) OD;
standard 1.0” IPS
schedule 40
Same
Weight (shipping
approx.)
3.2 lbs (5.5 lbs);
1.5 kg (2.3 kg)
2.5 lbs (5.5 lbs);
1.1 kg (2.3 kg)
Manufactured by RM Young (Traverse City, MI) and cabled by Campbell
Scientific for use with our dataloggers.
2

05103, 05106, and 05305 R.M. Young Wind Monitors
The black outer jacket of the cable is Santoprene® rubber. This
compound was chosen for its resistance to temperature extremes,
moisture, and UV degradation. However, this jacket will
support combustion in air. It is rated as slow burning when
tested according to U.L. 94 H.B. and will pass FMVSS302.
Local fire codes may preclude its use inside buildings.
NOTE
3. Installation
3.1 Siting
Locate wind sensors away from obstructions (e.g. trees and building). As a
general rule of thumb there should be a horizontal distance of at least ten times
the height of the obstruction between the windset and the obstruction. If it is
necessary to mount the sensors on the roof of a building, the height of the
sensors above the roof, should be at least 1.5 times the height of the building.
See Section 9 for a list of references that discuss siting wind speed and
direction sensors.
3.2 Assembly and Mounting
Tools Required:
•5/64” Allen wrench
•1/2” open end wrench
•compass and declination angle for the site (see Appendix A)
•small screw driver provided with datalogger
•UV resistant cable ties
•small pair of diagonal-cutting pliers
•6 - 10” torpedo level
Install the propeller to the propeller shaft using the nut provided with the
sensor.
The 05103 mounts to a standard 1” IPS schedule 40 pipe (1.31” O.D.). A 12”
long mounting pipe ships with the 03001 for attaching the sensor to a 019ALU
(Figure 3-1), or CM200 series crossarm with the CM220 or PN 1049 (Figures
3-2 and 3-3). The 05103 can also be mounted to a CM110 series tripod mast
with the CM216 Mast Mounting Kit.
Mount the 019ALU or CM200 series crossarm to the tripod or tower. Orient
the crossarm North-South, with the 1” Nu-Rail or CM220 on the North end.
Appendix A contains detailed information on determining true north using a
compass and the magnetic declination for the site.
Secure the mounting pipe to the 019ALU or CM220. Place the orientation
ring, followed by the 05103 on the mounting pipe. Orient the junction box to
the south, and tighten the band clamps on the orientation ring and mounting
post. Final sensor orientation is done after the datalogger has been
programmed to measure wind direction as described in Appendix A.
Route the sensor cable along the underside of the crossarm to the tower/tripod
mast, and to the instrument enclosure. Secure the sensor cable to the crossarm
and mast using cable ties.
3

05103, 05106, and 05305 R.M. Young Wind Monitors
YOUNG
Wind Monitor
Mounting Pipe
(supplied with sensor)
019ALU Crossarm
FIGURE 3-1. Wind Monitor Mounted to the 019ALU Crossarm
YOUNG
Wind Monitor
PN 17953 Nu-Rail
CM200 Series Crossarm Mounting Pipe
(supplied with sensor)
FIGURE 3-2. Wind Monitor Mounted to a CM200 Series Crossarm
with PN 17953 Nu-Rail
4

05103, 05106, and 05305 R.M. Young Wind Monitors
Wind Monitor
Mounting Pipe
(supplied with sensor)
CM220
CM200 Series Crossarm
FIGURE 3-3. Wind Monitor Mounted to a CM200 Series Crossarm
with CM220 Right Angle Mounting Kit
4. Wiring
Connections to Campbell Scientific dataloggers are given in Table 4-1. When
Short Cut for Windows software is used to create the datalogger program, the
sensor should be wired to the channels shown in the wiring diagram created by
Short Cut.
TABLE 4-1. Connections to Campbell Scientific Dataloggers
Color
Description
CR800
CR5000
CR3000
CR1000
CR510
CR500
CR10(X)
21X,
CR7
CR23X
CR200
Red Wind Spd.
Signal Pulse Pulse Pulse P_LL
Black Wind Spd.
Reference
G
Green Wind Dir. Signal SE Analog SE
Analog SE Analog SE Analog
Blue Wind Dir.
Excitation Excitation Excitation Excitation Excitation
White Wind Dir.
Reference
AG
Clear Shield wire
G
5

05103, 05106, and 05305 R.M. Young Wind Monitors
5. Example Programs
This section is for users who write their own programs. A datalogger program
to measure this sensor can be created using Campbell Scientific’s Short Cut
Program Builder software. You do not need to read this section to use Short
Cut.
5.1 Wind Speed
Wind speed is measured with the Pulse Count instruction, and with the low
level AC configuration. For dataloggers programmed with Edlog, specify
configuration code 21 to output frequency in Hertz.
The expression for wind speed (U) is:
U = MX + B
where
M = multiplier
X = number of pulses per second (Hertz)
B = offset
Table 5-1 lists the multipliers to obtain miles/hour or meters/second when the
Pulse Count instruction is configured to output Hz (configuration code 21).
The helicoid propeller has a calibration that passes through zero, so the offset
is zero (Gill, 1973; Baynton, 1976).
TABLE 5-1. Wind Speed Multiplier
(With Configuration Code 21*)
Model Miles/Hour Output Meters/Second Output
05103 or 05106 0.2192 0.0980
05305 0.2290 0.1024
*When configuration code 11 is used, the multiplier above is
divided by the execution interval in seconds.
5.2 Wind Direction
The wind vane is coupled to a 10K potentiometer, which has a 5 degree
electrical dead band between 355 and 360 degrees.
The EX-DEL_SE measurement instruction is used for dataloggers that are
programmed with Edlog (e.g. CR10X, CR23X) and the CR200. The
measurement result is mV; the multiplier to convert mV to degrees is
355deg/excitation mV.
The BRHalf measurement instruction is used for dataloggers that are
programmed with CRBasic (e.g. CR1000, CR3000). The multiplier to convert
the measurement result (mV/excitation mV) to degrees is 355.
6