C&T Solution CT-CIB61 User manual

CT-CIB61
Intel® 3rd Generation Core™ Processor i7/i5/i3/Celeron
COM Express™ Type 6 Module
User’s Manual
Version 1.0
C&T Solution Inc.
12F. -1, No.700, Zhongzheng Rd., Zhonghe Dist., New Taipei City 235, Taiwan
TEL: [phone]
http://www.candtsolution.com

CT-CIB61 Intel® 3rd Generation Core™ Processor i7/i5/i3 COM Express Type 6 Module
２
Table of Contents
I. Preface ..................................................................................................... ５
1.1 Disclaimer ...................................................................................... ５
1.2 Copyright Notice ............................................................................. ５
1.3 Trademarks Acknowledgment ........................................................ ５
II. Introduction.............................................................................................. ６
2.1 Product Description ........................................................................ ６
2.2 Specifications ................................................................................. ７
2.3 Block Diagram ................................................................................ ９
2.4 SKU ............................................................................................. １０
III. Mechanical Specification ..................................................................... １１
3.1 Module Dimensions ..................................................................... １１
3.2 Layout ......................................................................................... １２
3.3 Connectors and Switch ............................................................... １４
3.3.1 LPC Debug Port: CN3 ....................................................... １４
3.3.2 CPLD JTAGE .................................................................... １４
3.3.3 COM Express Connectors ................................................ １４
3.3.4 PCIE Port Bifurcation: SW1............................................... １８
3.4 Thermal Solutions ....................................................................... １８
3.4.1 Fan Sink ............................................................................ １８
3.4.2 Heat Spreader ................................................................... ２０
IV. Features & Interfaces .......................................................................... ２２
4.1 Processor .................................................................................... ２２
4.2 BIOS............................................................................................ ２２
4.3 System Memory .......................................................................... ２２
4.4 Chipset ........................................................................................ ２２
4.5 Graphics ...................................................................................... ２２
4.5.1 VGA Output ....................................................................... ２３
4.5.2 LVDS ................................................................................. ２４
4.5.3 DDI .................................................................................... ２４
4.6 USB ............................................................................................. ２７
4.6.1 USB 2.0 ............................................................................. ２７
4.6.2 USB 3.0 ............................................................................. ２８
4.7 SATA ........................................................................................... ２８
4.8 PCI Express ................................................................................ ２９
4.8.1 PCI Express x1 ................................................................. ２９
4.8.2 PCI Express x16 ............................................................... ３０

CT-CIB61 Intel® 3rd Generation Core™ Processor i7/i5/i3 COM Express Type 6 Module
３
4.9 High Definition Audio ................................................................... ３０
4.10 Ethernet ..................................................................................... ３０
4.11 LPC ........................................................................................... ３１
4.12 SPI ............................................................................................ ３１
4.13 SMBus ....................................................................................... ３２
4.14 ExpressCard ............................................................................. ３３
4.15 General Purpose Input Output .................................................. ３３
4.15.1 GPIO Configuration ......................................................... ３３
4.15.2 Registers Description ...................................................... ３４
4.15.3 PSUEDO CODE .............................................................. ３６
4.16 Watchdog Timer ........................................................................ ３７
4.16.1 Board Design .................................................................. ３７
4.16.2 PSUEDO CODE .............................................................. ３７
4.17 Power and System Management Signals .................................. ３８
4.18 Thermal Management Signals .................................................. ３８
4.19 Miscellaneous Signals ............................................................... ３８
V. SYSTEM BIOS ..................................................................................... ３９
5.1 Main ............................................................................................ ３９
5.2 Advanced .................................................................................... ４０
5.2.1 ACPI Settings .................................................................... ４１
5.2.2 Trusted Computing ............................................................ ４２
5.2.1 CPU Configuration ............................................................ ４３
5.2.2 SATA Configuration .......................................................... ４４
5.2.3 USB Configuration ............................................................ ４５
5.2.4 W83627DHG Super IO Configuration ............................... ４６
5.2.5 W83627DHG H/W Monitor ................................................ ４８
5.2.6 F81801 Super IO Configuration ........................................ ４９
5.2.7 F81801 H/W Monitor ......................................................... ５１
5.2.8 Serial Port Console Redirection ........................................ ５２
5.2.9 CPU PPM Configuration ................................................... ５３
5.3 Chipset ........................................................................................ ５４
5.3.1 PCH-IO Configuration ....................................................... ５５
5.3.2 System Agent Configuration.............................................. ６０
5.4 Boot ............................................................................................. ６５
5.4.1 CSM16 Parameters ........................................................... ６６
5.4.2 CSM Parameters ............................................................... ６７
5.5 Security ....................................................................................... ６８

CT-CIB61 Intel® 3rd Generation Core™ Processor i7/i5/i3 COM Express Type 6 Module
４
5.6 Save and Exit .............................................................................. ６９
VI. Address Map ....................................................................................... ７０
6.1 I/O Port Address Map .................................................................. ７０
6.2 Interrupt Controller (IRQ) Map ..................................................... ７２
6.3 Memory Map ............................................................................... ７５
VII. Electrical Specification ....................................................................... ７６
7.1 Input Power ................................................................................. ７６

CT-CIB61 Intel® 3rd Generation Core™ Processor i7/i5/i3 COM Express Type 6 Module
５
I. Preface
1.1 Disclaimer
All specifications and information in this User’s Manual are believed to be
accurate and up to date. C&T Solution Inc. does not guarantee that the
contents herein are complete, true, accurate or non-misleading. The
information in this document is subject to change without notice and does not
represent a commitment on the part of C&T Solution Inc.
C&T Solution Inc. disclaims all warranties, express or implied, including,
without limitation, those of merchantability, fitness for a particular purpose with
respect to contents of this User’s Manual. Users must take full responsibility for
the application of the product.
1.2 Copyright Notice
All rights reserved. No part of this manual may be reproduced or transmitted in
any form or by any means, electronic or mechanical, including photocopying,
recording, or information storage and retrieval systems, without the prior
written permission of C&T Solutions Inc.
Copyright © 2012 C&T Solutions Inc.
1.3 Trademarks Acknowledgment
Intel®, Celeron® and Pentium® are trademarks of Intel Corporation.
Windows® is registered trademark of Microsoft Corporation.
AMI is trademark of American Megatrend Inc.
IBM, XT, AT, PS/2 and Personal System/2 are trademarks of International
Business Machines Corporation
All other products and trademarks mentioned in this manual are trademarks of
their respective owners.

CT-CIB61 Intel® 3rd Generation Core™ Processor i7/i5/i3 COM Express Type 6 Module
６
II. Introduction
2.1 Product Description
The CT-CIB61 is a new COM (computer-on-module) Express® basic form
factor (125x95mm) in embedded computing platforms. It combines a socket G
for Intel® 3rd Generation Core i7/i5/i3 processors with Intel® QM77 Express
chipset. With specified configurations, three display could be supported. The
CT-CIB61 is based on the COM Express® specification and features a
standardized connector layout that carries a specified set of signals. With the
Type 6 pin-out connectors, the CT-CIB61 supports HDMI/DVI/LVDS/VGA,
SATA, HD audio, Gigabit Ethernet, PCIe and USB3.0. This system requires a
Carrier Board to bring out I/O and power up. The benefit of this standardization
pin-out is making the application design more flexible. To accommodate
different ODM requirements, the COM Express module with a Carrier Board is
the best cost-effective solution and reduces development time.

CT-CIB61 Intel® 3rd Generation Core™ Processor i7/i5/i3 COM Express Type 6 Module
７
2.2 Specifications
 CPU
 Intel® 3rd Generation Core i7/ i5/ i3/ Celeron processor
 Socket G (rPGA988)
 Chipset
 Intel® QM77 Express Chipset
 System Memory
 Two 204-pin DDR3/DDR3L SODIMM sockets
 Up to 1600MHz
 Up to 32GB
 BIOS
 AMI uEFI BIOS
 8MB SPI Flash ROM
 iAMT
 iAMT8.0
 Graphics
 Intel® HD Graphics 4000 integrated with CPU
 Support up to three displays
 Resolution up to 2560x1600
 Two channels of 24-bit LVDS interface
 Support HDMI / DVI / LVDS/DisplayPort / SDVO
 Ethernet
 Intel® 82579LM
 10/100/1000 Mbps
 Audio
 Integrated in chipset Intel® QM77
 SATA Interface
 Two SATA 6Gb/s ports
 Two SATA 3Gb/s ports
 PCIe Lane
 One PCIex16 Lanes
 Six PCIex1 Lanes
 USB Interface
 Eight USB 2.0 ports
 Four USB 3.0 ports

CT-CIB61 Intel® 3rd Generation Core™ Processor i7/i5/i3 COM Express Type 6 Module
８
 Two UART Ports
 LPC Interface
 SMBus
 SPI Interface
 8-bit GPIO
 Watchdog Timer
 H/W Monitor
 Power Management
 ACPI (Advanced Configuration and Power Interface)
 Form Factor
 Basic size, 125mm x 95mm

CT-CIB61 Intel® 3rd Generation Core™ Processor i7/i5/i3 COM Express Type 6 Module
９
2.3 Block Diagram
Connector ROW A
,
B
Connector ROW AB
CPU
Ivy Bridge
DDR3
/DDR3L
1333/1600MHz
2xSATA 6G; 2xSATA 3G
SPI
PCIEx1, Port 0~Port5
8xUSB2.0
VGA
HDA
Connector ROW C
,
D
Connector ROW AB
PEG; 1x16;
2x8 &2x4
GbE
PCH
Intel QM77
GPIx4; GPOx4
Debug
Port
TPM
Channel A
204pin
SODIMM
HWM
NCT7802Y
DMI
SM Bus
24
-
bit LVDS dual
-
channel
BIOS
LPC
CPLD
FDI
Channel B
204pin
SODIMM
DDR3
/DDR3L
1333/1600MHz
Super
I/O
I2C
Tx/Rx x2
SM Bus
Intel
82579LM
PCIEx1
Port 7
SDVO/Display Port/HDMI
Display Port/HDMI
Display Port/HDMI
PCIEx1, Port 6
4xUSB3.0
System
clock out
25 MHz
crystal

CT-CIB61 Intel® 3rd Generation Core™ Processor i7/i5/i3 COM Express Type 6 Module
１０
2.4 SKU
Product
Number Processor PCH Features
CT-CIB61 Socket G for 3rd
Gen Core i7,i5,i3
QM77
2xDDR3, LVDS, VGA, 3xDDI, PCIex16, 7xPCIex1,
GbE, 4xUSB3.0, 8xUSB2.0, 4xSATA, GPIO,
iAMT8.0

CT-CIB61 Intel® 3rd Generation Core™ Processor i7/i5/i3 COM Express Type 6 Module
１１
III. Mechanical Specification
3.1 Module Dimensions
The PCB size of CT-CIB61 is 125mm x 95mm, the standard COM Express
Basic Module size.
The holes shown in the drawing below is for stacking the module with the Heat
Spreader / Fan Sink and the Carrier Board. The mounting holes are 2.7mm,
and the 2.5mm hardware shall be used. The position and the dimension of the
holes are shown in the unit of millimeters.

CT-CIB61 Intel® 3rd Generation Core™ Processor i7/i5/i3 COM Express Type 6 Module
１２
3.2 Layout
There are two SODIMM sockets. Each of them is mounted separately on each
side of the CT-CIB61. Two 220-pin COM Express connectors are mounted at
the bottom side of the PCB.

CT-CIB61 Intel® 3rd Generation Core™ Processor i7/i5/i3 COM Express Type 6 Module
１３
Top Side:
Bottom Side:
CN1
CN4
CN3
SW1
CN5
CN6
CN2

CT-CIB61 Intel® 3rd Generation Core™ Processor i7/i5/i3 COM Express Type 6 Module
１４
3.3 Connectors and Switch
Connector Description
CN1 Top DDR3 SO-DIMM Connector
CN2 Bottom DDR3 SO-DIMM Connector
CN3 LPC Debug Port
CN4 CPLD JTAGE
CN5 COM™ Express connector Row A, B
CN6 COM™ Express connector Row C, D
SW1 PCIE Port Bifurcation Straps
LPC Debug Port: CN3 3.3.1
1 GND 2 3.3V
3 LPC_AD3 4 BIOS_DIS0_L
5 LPC_AD2 6 RESET
7 LPC_AD1 8 CLOCK
9 LPC_AD0 10 FRAME
CPLD JTAGE 3.3.2
1 3.3V 2 GND
3 TDO 4 GND
5 TDI 6 GND
7 TMS 8 GND
9 TCK 10 GND
COM Express Connectors 3.3.3
The CT-CIB61 is connected to the carrier board via two 220-pin connectors.
Each connector is break down into two rows. The first connector, CN5,
consists Row A and Row B; the second connector, CN6, consists Row C and
Row D. Their pin-out is as table below.

CT-CIB61 Intel® 3rd Generation Core™ Processor i7/i5/i3 COM Express Type 6 Module
１５
Pin
Row A Row B Row C Row D
1 GND(FIXED) GND(FIXED) GND(FIXED) GND(FIXED)
2 GBE0_MDI3- GBE0_ACT# GND GND
3 GBE0_MDI3+ LPC_FRAME# USB_SSRX0- USB_SSTX0-
4 GBE0_LINK100# LPC_AD0 USB_SSRX0+ USB_SSTX0+
5 GBE0_LINK1000# LPC_AD1 GND GND
6 GBE0_MDI2- LPC_AD2 USB_SSRX1- USB_SSTX1-
7 GBE0_MDI2+ LPC_AD3 USB_SSRX1+ USB_SSTX1+
8 GBE0_LINK# LPC_DRQ0# GND GND
9 GBE0_MDI1- LPC_DRQ1# USB_SSRX2- USB_SSTX2-
10 GBE0_MDI1+ LPC_CLK USB_SSRX2+ USB_SSTX2+
11 GND(FIXED) GND(FIXED) GND(FIXED) GND(FIXED)
12 GBE0_MDI0- PWRBTN#- USB_SSRX3- USB_SSTX3-
13 GBE0_MDI0+ SMB_CK USB_SSRX3+ USB_SSTX3+
14 GBE0_CTREF SMB_DAT GND GND
15 SUS_S3# SMB_ALERT# DDI1_PAIR6+ DDI1_CTRLCLK_AUX+
16 SATA0_TX+ SATA1_TX+ DDI1_PAIR6- DDI1_CTRLDATA_AUX-
17 SATA0_TX- SATA1_TX- NC NC
18 SUS_S4# SUS_STAT# NC NC
19 SATA0_RX+ SATA1_RX+ PCIE_RX6+ PCIE_TX6+
20 SATA0_RX- SATA1_RX- PCIE_RX6- PCIE_TX6-
21 GND(FIXED) GND(FIXED) GND(FIXED) GND(FIXED)
22 SATA2_TX+ SATA3_TX+ NC NC
23 SATA2_TX- SATA3_TX- NC NC
24 SUS_S5# PWR_OK DDI1_HPD NC
25 SATA2_RX+ SATA3_RX+ DDI1_PAIR4+ NC
26 SATA2_RX- SATA3_RX- DDI1_PAIR4- DDI1_PAIR0+
27 BATLOW# WDT NC DDI1_PAIR0-
28 (S)ATA_ACT# AC/HAD_SDIN2 NC NC
29 AC/HDA_SYNC AC/HAD_SDIN1 DDI1_PAIR5+ DDI1_PAIR1+
30 AC/HAD_RST# AC/HAD_SDIN0 DDI1_PAIR5- DDI1_PAIR1-
31 GND(FIXED) GND(FIXED) GND(FIXED) GND(FIXED)
32 AC/HDA_BITCLK SPKR DDI2_CTRLCLK_AUX+ DDI1_PAIR2+
33 AC/HAD_SDOUT I2C_CK DDI2_ CTRLDATA_AUX- DDI1_PAIR2-
34 BIOS_DIS0# I2C_DAT DDI2_DDC_AUX_SEL DDI1_DDC_AUX_SEL
35 THRMTRIP# THRM# NC NC
36 USB6- USB7- DDI3_CTRLCLK_AUX+ DDI1_PAIR3+
37 USB6+ USB7+ DDI3_ CTRLDATA_AUX- DDI1_PAIR3-
38 USB_6_7_OC# USB_4_5_OC# DDI3_DDC_AUX_SEL NC

CT-CIB61 Intel® 3rd Generation Core™ Processor i7/i5/i3 COM Express Type 6 Module
１６
Pin
Row A Row B Row C Row D
39 USB4- USB5- DDI3_PAIR0+ DDI2_PAIR0+
40 USB4+ USB5+ DDI3_PAIR0- DDI2_PAIR0-
41 GND(FIXED) GND(FIXED) GND(FIXED) GND(FIXED)
42 USB2- USB3- DDI3_PAIR1+ DDI2_PAIR1+
43 USB2+ USB3+ DDI3_PAIR1- DDI2_PAIR1-
44 USB_2_3_OC# USB_0_1_OC# DDI3_HPD DDI2_HPD
45 USB0- USB1- NC NC
46 USB0+ USB1+ DDI3_PAIR2+ DDI2_PAIR2+
47 VCC_RTC EXCD1_PERST# DDI3_PAIR2- DDI2_PAIR2-
48 EXCD0_PERST# EXCD1_CPPE# NC NC
49 EXCD0_CPPE# SYS_RESET# DDI3_PAIR3+ DDI2_PAIR3+
50 LPC_SERIRQ CB_RESET# DDI3_PAIR3- DDI2_PAIR3-
51 GND(FIXED) GND(FIXED) GND(FIXED) GND(FIXED)
52 PCIE5_TX+ PCIE5_RX+ PEG_RX0+ PEG_TX0+
53 PCIE5_TX- PCIE5_RX- PEG_RX0- PEG_TX0-
54 GPI0 GPO1 NC PEG_LANE_RV#
55 PCIE4_TX+ PCIE4_RX+ PEG_RX1+ PEG_TX1+
56 PCIE4_TX- PCIE4_RX- PEG_RX1- PEG_TX1-
57 GND GPO2 NC GND
58 PCIE3_TX+ PCIE3_RX+ PEG_RX2+ PEG_TX2+
59 PCIE3_TX- PCIE3_RX- PEG_RX2- PEG_TX2-
60 GND(FIXED) GND(FIXED) GND(FIXED) GND(FIXED)
61 PCIE2_TX+ PCIE2_RX+ PEG_RX3+ PEG_TX3+
62 PCIE2_TX- PCIE2_RX- PEG_RX3- PEG_TX3-
63 GPI1 GPO3 NC NC
64 PCIE1_TX+ PCIE1_RX+ NC NC
65 PCIE1_TX- PCIE1_RX- PEG_RX4+ PEG_TX4+
66 GND WAKE0# PEG_RX4- PEG_TX4-
67 GPI2 WAKE1# NC GND
68 PCIE0_TX+ PCIE0_RX+ PEG_RX5+ PEG_TX5+
69 PCIE0_TX- PCIE0_RX- PEG_RX5- PEG_TX5-
70 GND(FIXED) GND(FIXED) GND(FIXED) GND(FIXED)
71 LVDS_A0+ LVDS_B0+ PEG_RX6+ PEG_TX6+
72 LVDS_A0- LVDS_B0- PEG_RX6- PEG_TX6-
73 LVDS_A1+ LVDS_B1+ GND GND
74 LVDS_A1- LVDS_B1- PEG_RX7+ PEG_TX7+
75 LVDS_A2+ LVDS_B2+ PEG_RX7- PEG_TX7-
76 LVDS_A2- LVDS_B2- GND GND

CT-CIB61 Intel® 3rd Generation Core™ Processor i7/i5/i3 COM Express Type 6 Module
１７
Pin
Row A Row B Row C Row D
77 LVDS_VDD_EN LVDS_B3+ NC NC
78 LVDS_A3+ LVDS_B3- PEG_RX8+ PEG_TX8+
79 LVDS_A3- LVDS_BKLT_EN PEG_RX8- PEG_TX8-
80 GND(FIXED) GND(FIXED) GND(FIXED) GND(FIXED)
81 LVDS_A_CK+ LVDS_B_CK+ PEG_RX9+ PEG_TX9+
82 LVDS_A_CK- LVDS_B_CK- PEG_RX9- PEG_TX9-
83 LVDS_I2C_CK LVDS_BKLT_CTRL
NC NC
84 LVDS_I2C_DAT VCC_5V_SBY GND GND
85 GPI3 VCC_5V_SBY PEG_RX10+ PEG_TX10+
86 NC VCC_5V_SBY PEG_RX10- PEG_TX10-
87 NC VCC_5V_SBY GND GND
88 PCIE_CK_REF0+ BIOS_DIS1# PEG_RX11+ PEG_TX11+
89 PCIE_CK_REF0- VGA_RED PEG_RX11- PEG_TX11-
90 GND(FIXED) GND(FIXED) GND(FIXED) GND(FIXED)
91 SPI_POWER VGA_GRN PEG_RX12+ PEG_TX12+
92 SPI_MISO VGA_BLU PEG_RX12- PEG_TX12-
93 GPO0 VGA_HSYNC GND GND
94 SPI_CLK VGA_VSYNC PEG_RX13+ PEG_TX13+
95 SPI_MOSI VGA_I2C_CK PEG_RX13- PEG_TX13-
96 TPM_PP VGA_I2C_DAT GND GND
97 NC SPI_CS# NC NC
98 SER0_TX NC PEG_RX14+ PEG_TX14+
99 SER0_RX NC PEG_RX14- PEG_TX14-
100
GND(FIXED) GND(FIXED) GND(FIXED) GND(FIXED)
101
SER1_TX FAN_PWMOUT PEG_RX15+ PEG_TX15+
102
SER1_RX FAN_TACHIN PEG_RX15- PEG_TX15-
103
LID# SLEEP# GND GND
104
VCC_12V VCC_12V VCC_12V VCC_12V
105
VCC_12V VCC_12V VCC_12V VCC_12V
106
VCC_12V VCC_12V VCC_12V VCC_12V
107
VCC_12V VCC_12V VCC_12V VCC_12V
108
VCC_12V VCC_12V VCC_12V VCC_12V
109
VCC_12V VCC_12V VCC_12V VCC_12V
110
GND(FIXED) GND(FIXED) GND(FIXED) GND(FIXED)

CT-CIB61 Intel® 3rd Generation Core™ Processor i7/i5/i3 COM Express Type 6 Module
１８
PCIE Port Bifurcation: SW1 3.3.4
Pin1&4 Pin2&3 Function Switch
OFF OFF (Default) x16 Device 1 function 1 and 2
disabled
OFF ON X8, x8 – Device 1 function enabled;
function 2 disabled
ON OFF Reserved – (Device 1 function
disabled; function 2 enabled)
ON ON x8, x4, x4 – Device 1 functions 1 & 2
enabled
3.4 Thermal Solutions
There are two thermal solutions for the COM Module CT-CIB61 to dissipate
the heat. One is by using a fan sink and the other one is by using a heat
spreader.
Fan Sink 3.4.1
Step 1: Place the fan sink on top of the CT-CIB61 module.
Step 2: Use three screws (M2.5x5L) to secure the fan sink with the CT-CIB61,
as illustrated below.
Step 3: Connect the COM Express connectors on the CT-CIB61 to the
corresponding COM connectors on the Carrier Board. Make sure the four
holes at the corners of CT-CIB61 module align to the corresponding pillars on
the Carrier Board.
Step4: Use five screws (M2.5x15L) to secure the fan sink with the Carrier
Board through the corresponding holes on the CT-CIB61.

CT-CIB61 Intel® 3rd Generation Core™ Processor i7/i5/i3 COM Express Type 6 Module
１９

CT-CIB61 Intel® 3rd Generation Core™ Processor i7/i5/i3 COM Express Type 6 Module
２０
Heat Spreader 3.4.2
A heat spreader is designed for the CT-CIB61 to dissipate heat. All heat
generating components are thermally conducted to the heat spreader in order
to avoid hot spots.
Step 1: Place the heat spreader plate on top of the CT-CIB61 module.
Step 2: Use three screws (M2.5x5L) to secure the heat spreader with the
CT-CIB61, as illustrated below.
Step 3: Connect the COM Express connectors on the CT-CIB61 to the
corresponding COM connectors on the Carrier Board. Make sure the four
holes at the corners of CT-CIB61 module align to the corresponding pillars on
the Carrier Board.
Step4: Use five screws (M2.5x15L) to secure the heat spreader with the
Carrier Board through the corresponding holes on the CT-CIB61.