Canon CR-N300 User manual

This "Installation Guide/Important Information" is comprised of pages [1/2] and [2/2].
Please be sure to read the "Safety Precautions" section for correct use.After
reading this
" Installation Guide/Important Information "
,keep it in a readily
accessible location for future reference.This camera is for indoor use only.
•The cameras described in this document may include models not
available in your country and/or region.
•HDMI is a trademark or registered trademark of HDMI Licensing
Administrator,Inc.in the United States and other countries.
•All other company or product names used in this document are
trademarks or registered trademarks of their respective holders.
•The contents of this document are subject to change without any prior
notice.
The latest user manuals and software,etc.for this product can be
downloaded from the following website.The user manuals explain the
camera settings and operations.Read them carefully before using the
camera to ensure correct use.
global.canon/ncsp
List of Downloadable Files
User Manuals Software
•Settings Guide
•Remote Camera Control
Application User Manual
•Camera Search Tool
•Remote Camera Control
Application
Firmware
(only provided at time of update)
Check Included Items
Camera
Ceiling Plate
Camera-to-Mount Safety Wire 10 cm (3.94 in.)
M3 Screw x 4L (2)(for camera-to-mount safety wire,and camera mounting)
Safety Wire 3 m (9.8 ft.)
Wire Stopper (for safety wire)
M3 Screw x 6L (4)(for wire stopper)
Compact Power Adapter
Power Cable
IR Remote Controller
Size AAA Battery (2)(for IR remote controller)
Printed Materials
Symbols used in this manual
Parts indicated in the
" Installation Guide/Important Information "
[2/2]
with this icon are not included with the camera,and should be prepared
by the user.
M: Outer diameter of the screw shaft (mm)
L: Length (mm)
Safety Precautions
Warning
Failure to follow the instructions may
result in death or serious injury.
Do not install in the following places:
•Places in direct sunlight,near heat-generating objects,or locations subject
to high temperatures.
•Places near fire sources or flammable solvents (alcohol,thinner,fuel,etc.).
•Humid or dusty places.
•Places subject to oily smoke or steam.
•Confined or enclosed places.
Failure to do so may result in fire or electric shock.
Notes on installation at high places
•For installation or inspection of this camera,consult the dealer where you
purchased the product.
•Install the camera in a way that ensures sufficient holding strength
according to the mounting place such as the wall,ceiling,etc.Also,make
sure that the mounting place can sufficiently support the total weight
including the mounting parts and reinforce it if necessary.
•Prepare fixing screws suitable for the location and type of surface the
camera is to be installed.
•Periodically check the mounting brackets and screws for rust and
loosening.
•Do not install in unstable places,places subject to significant vibration or
impact,or places subject to salt damage or corrosive gas.
•Be sure to attach the safety wire when installing the camera.
•Use the included ceiling plate to install the camera.Do not install it with
only the tripod screws.
Failure to do so may result in the camera falling or other accidents.
General notes on the camera
•If any defective conditions such as smoke,strange sounds,heat,strange
odors,damage or cracks on the external case are discovered,immediately
stop using the camera,unplug the power cable from the outlet (or the LAN
cable for PoE+power supply), and contact your nearest dealer.Place the
compact power adapter near the power outlet and avoid placing objects
around the power plug so that the power can be turned off immediately in
the event of an emergency.
•Do not touch the camera or the connecting cables during a thunderstorm.
•Do not disassemble or modify the camera.
•Do not scratch,pull,or forcefully bend the cables,or put a load on their
connections.
•Do not spray the camera with water,or otherwise make it wet.
•Do not touch the camera,the compact power adapter,cable connectors,
power plugs,or power outlets with wet hands.
•Do not allow water,metal or other foreign objects to enter the camera.
•Do not use flammable sprays near the camera.
•Do not leave the compact power adapter (or the LAN cable for PoE+
power supply)connected when the camera is not in use for long periods.
•Do not use flammable solvents such as alcohol,paint thinner or benzine
when cleaning the camera.
•Do not block the air exit vents.
Failure to do so may result in fire or electric shock.
Notes on Power Supply
•Use only the included compact power adapter when using an AC adapter.
•The included compact power adapter and power cable are for this
product only.They cannot be used for other devices.
•Do not place heavy objects on the power cable (or the LAN cable for PoE+
power supply)or pull,forcibly bend,scratch or modify it.
•Do not allow metal pins or debris to touch the power plug or terminals.
•Wipe any dust off of the power plug.Also,if the connection is made to the
power outlet in a dusty area,take measures to prevent tracking.
•Make sure the power plug (or the LAN cable for PoE+power supply)is
seated all the way,and do not use it when the insertion is insufficient.
•Do not use a damaged power plug or a loose power outlet,or use it in a
manner that exceeds the rating of the wiring device such as connecting
multiple plugs to an outlet.
Failure to do so may result in fire or electric shock.
Notes on batteries
•Do not put batteries in the fire,or do not heat,short circuit or disassemble
them.
•Do not charge the included batteries.
•Do not use batteries other than those specified.
Failure to do so may result in fire or electric shock.
Do not use the product at:
•Places where the use is prohibited,such as in hospitals and on airplanes.
•Places within reach of babies and toddlers.
ENGLISH
Installation Guide
Important Information
1
2
BIE-7292-000
© CANON INC.2021 Printed in Japan
Use at such places can cause equipment to malfunction due to
radio waves and lead to accidents,or cause electric shock and
injuries.
Caution
Failure to follow the instructions may
result in injuries or property damages.
Notes on installation
•Installation must be carried out safely and securely in accordance with the
relevant regulations for technical standards of electrical installation.
Failure to do so may result in accidents.
Notes on installation
•Take care not to damage wiring or piping.
Failure to do so may result in damage to surrounding items.
General notes on the camera
•Do not touch the edges of metal parts with bare hands.
•Be careful not to get your fingers caught when installing.
Failure to do so may result in injuries.
Notes on batteries
•Remove the batteries when they have been used up or will not be used for
a long time.
•When replacing the batteries,replace both batteries at the same time.
Also,do not use different types of batteries together.
•Make sure +and
-
of the battery are oriented correctly.
•If any liquid from inside the battery gets on your body due to leakage,
rinse it off thoroughly with water.
Failure to do so may result in injuries and malfunctions.
Important
•Do not install the camera in places where radiation,X-rays,strong radio
waves or strong magnetism are generated.It may cause video and
audio disturbance,noise,or malfunctions.
•We recommend the installation of a lightning arrester (a surge protection
device)as a measure against failures caused by lightning strikes.
•Take measures to remove static electricity before performing any
procedures.
•Do not connect the compact power adapter to a transformer.
•If there is condensation,please wait to power on,until the condensation
dissipates.
•Do not hold the device by the camera head.
•Do not turn the camera rotator by hand.
•After turning off the power,do not turn the power on again for at least
five seconds.
•Do not point the camera at strong light sources (such as the sun on a
clear day or strong artificial light sources). Internal components such as
the image sensor could be damaged.
•Do not carry the camera on a tripod.
Precautions for Use (Disclaimer)
Compliance with Applicable Laws/intellectual Property Rights: Please note
that your use of this product may subject you to certain laws,rules and
regulations,including but not limited to,privacy,wiretapping and intellectual
property and publicity laws.Please be sure your use of this product and/or
any resulting recordings or footage complies with applicable laws,rules and
regulations.
Canon Inc.and its affiliates shall have absolutely no liability with respect
to any claims made by third parties that your use of this product does not
comply with applicable laws,rules and regulations and any resulting claims
brought against you by third parties alleging non-compliance with such laws,
or otherwise violates any third party's intellectual property,personal,privacy
or proprietary rights as a result of your use of the product.We are also not
responsible to you for any liability whatsoever resulting from your use,and/or
installation of this product,and/or any loss of any recordings or footage.
Limited Warranty: Please check the in-box materials for more information
about the limited warranty that pertains to your product.
Installation: This product should NOT be installed outdoors.You are solely
responsible for the proper installation of this product.To the extent permitted
by law,Canon Inc.and its affiliates shall have absolutely no liability to you
with respect to any damages or liabilities associated with the improper use of,
or the installation of this product,or for any personal injuries sustained by you
or any third parties as a result of any such improper use or installation of this
product,whether or not the installation of this product was by you,or by any
third party.
Privacy:
•Do not install this product in areas where people have a reasonable
expectation of privacy,including but not limited to,bedrooms,dressing
rooms,locker rooms and rest room facilities.
•Some jurisdictions require signage disclosing the existence of camera
equipment. Please check your own area's laws for requirements.
•Making audio recordings is heavily regulated and can vary significantly
by area.Please check laws in your jurisdiction before making any audio
recordings.
OTHER IMPORTANT INFORMATION: Please see other important information
pertaining to the use of this product by reading our Settings Guide,which
can also be found at global.canon/ncsp,prior to using this product.
About lamp
POWER lamp STATUS lamp Status
Green light
BLINKING OFF Power being switched on
Green light ON OFF POWER ON
Green light
BLINKING (twice)OFF Signal received from IR remote
controller
Orange light ON Orange light ON Standby
Green light
BLINKING OFF Changing to or from standby
OFF Orange light ON Insufficient power
OFF Orange light
BLINKING
Pan/Tilt position error,
firmware being updated
Green light
BLINKING
Orange light
BLINKING Device failure
Tally lamp Status
Red light ON Streaming
Green light ON Preparing
streaming
Before using the camera
Initial settings
Be sure to make the initial settings before use.If the initial settings are not
made,HDMI/SDI output and IP streaming cannot be executed.Also,when
using as a USB camera,change the Service switch after the initial settings.
SERVICE switch settings
Set the camera number to be operated by the IR remote controller with the
two switches on the left.
When using as a USB camera,the 3rd switch from the left is to be switched
to the bottom.
Switches should be set before turning on the power.
USB camera
REMOTE CAMERA

Notes for When and After
Installing the Camera
When Installing the Camera
Installation at high places
Caution
Request a professional installer for all
installation work.Never try to install the
camera yourself.Doing so may result in
unforeseen accidents such as dropping
the camera or electric shock.
When installing the camera at a high place,fix the camera to the ceiling plate
tightly fixed with four screws.
To fix the ceiling plate,use the screws such as M4 (pan head,binding head,
etc.) which fits the 4 mm (0.16 in.) diameter screw holes.
When working with the camera upside down,support the camera to prevent it
from wobbling in order to attach or remove the camera-to-mount safety wire.
Ceiling mount
The camera is hung upside down from the ceiling or other location using the
ceiling plate.
The procedure provided in the "Installation Guide/Important Information" [2/2]
explains this installation method.The weight of the camera (body only)is
Approx.2.2 kg (4.86 lb.). Reinforce the ceiling depending on its structure and
material to ensure the sufficient holding strength to support the total weight
including the camera and the mounting parts,and install.
Standing mount
The camera is fixed to a high place using the ceiling plate.
Follow the same procedure as for the ceiling mount,except for the direction
of the camera and logo plate inversion.
Tripod mount
Attach the tripod by fixing a screw to the screw hole for tripod.
Use 1/4-20UNC screws and tighten them securely,and set the tripod on a
flat surface with no steps.
Also refer to the instructions in the "Installation Guide/Important Information"
[2/2],if necessary.
1/4-20UNC
4.5 – 5.5 mm (0.18 – 0.22 in.)
Desktop
Install the camera on a stable,horizontal surface such as a table.
Also refer to the instructions in the "Installation Guide/Important Information"
[2/2],if necessary.
Connecting the Camera
1 2 3 4 5 6
13 789101112
1. LAN terminal
This terminal is for a network connection (RJ-45 connector).
The built-in PoE+(Power over Ethernet+) function allows the camera to be
powered by a PoE+HUB that complies with IEEE802.3at Type 2 via a LAN cable.
Use a category 5e or higher STP (shielded type)LAN cable,up to 100 m (328 ft.)
in length.
Important
•Some PoE+HUBs can limit the power for each port,but applying limits
may interfere with performance.In this case,do not limit the power.
•Some PoE+HUBs have limits for the total power consumption for
the ports,which can interfere with performance when multiple ports
are in use.For more information,check the instruction guide for the
corresponding PoE+HUB.
2. USB terminal (Type-C)
Terminal for UVC (USB Video Class).
In order to use as a USB camera,the Service switch needs to be set.
Refer to "Before using the camera" > "SERVICE switch settings".
3. USB terminal (Type-A)
For future expansion.
4. Memory card slot
For future expansion.
5. HDMI OUT terminal
Terminal for HDMI output.
6. 3G-SDI OUT terminal
Terminal for 3G-SDI output (BNC).
7. GND terminal
Ground terminal of the camera.
It is used to install a lightning arrester (surge protection devices).
8. MIC terminal
Stereo 3.5 mm (0.14 in.) terminal for audio input.It can be used for
microphone/line input.
•Microphone input: Input impedance 1.5k Ωor higher
Microphone power: 2.4 V ±0.2 V
Bias resistance: 2.2 k Ω±5%
•Line input: Input impedance 1.5 k Ωor higher
9. RESET switch
Initialize the camera settings to the factory defaults.Refer to the "Settings
Guide" for details.
10. SERVICE switch
Set the camera number operated by the IR remote controller.
(Refer to "Before using the camera" > "SERVICE switch settings".)
11. RS-422 terminal
Serial terminal (RJ-45 connector)for RS-422.
Connect the GNDs on both ends to stabilize the voltage level of the signal.
Use category 5e or higher STP cables.
Pin
number Function
1 TX
-
Output (
- )
2 TX+Output (+)
3 RX
-
Input (
- )
4 GND –
5 GND –
6 RX+Input (+)
7 NC –
8 NC –
12. DC IN 24V terminal
Power supply terminal for the compact power adapter.
13. Cable clamp
Cable clamp to prevent cord disconnection.
Pass the compact power supply cord through the clamp to prevent the cord
from coming off.
Note
•The camera is not equipped with a power switch.To turn the camera
on and off,insert and remove the cable of the compact power adapter
connected to the "12.DC IN 24V terminal" or the PoE+HUB connected
to the "1.LAN terminal",which supplies power.
When both the PoE+HUB and the compact power adapter are
connected,the compact power adapter takes priority.If the compact
power adapter is disconnected while both adapters are connected,
power to the camera will be interrupted.In this case,power can be
restored by disconnecting and reconnecting the LAN cable.
•The audio input method and the power to the microphone are to be set in
the Settings Page.Refer to the "Settings Guide" for details.
Specifications
Please refer to the 'Specifications'in the 'Appendix'of the "Settings Guide"
for specifications not listed below.
Pan operation range: Horizontal ±170°
Tilt operation range: Vertical
-
30°–+100°
Operating Environment: Temperature: 0 –+40 (+32°F –+104°F)
Humidity: 10% –90% (without condensation)
Storage Environment: Temperature: 0 –+40 (+32°F –+104°F)
Humidity: 10% –90% (without condensation)
Power Consumption: PoE+Input: Approx.16.2 W*max.(body only)
DC Input: Approx.15.0 W max.(body only)
*Class 4 (25.5 W required)for power supply devices
Dimensions (W x H x D): Approx.154 x 178 x 164 mm (6.06 x 7.01 x 6.46 in.)
(excluding protrusions)
Weight: Approx.2.2 kg (4.86 lb.) (body only)
Country Regulations
About wireless communication
Regarding countries and regions where radio communication functions are
acceptable
Since the utilization of the radio communication functions can be legally
restricted by a country or region,it may not be possible to utilize out of the
country or the region where the product is purchased.Canon shall not be
liable for any incidents that may incur as a result of the utilization of the
radio communication functions in any country or region other than where the
product is purchased.
FCC NOTICE
Remote Camera,Model Name: CR-N300
This device complies with Part 15 of the FCC Rules.Operation is subject
to the following two conditions: (1)This device may not cause harmful
interference,and (2)this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for
a Class A digital device,pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates,uses,and can radiate radio frequency energy
and,if not installed and used in accordance with the user manual,may cause
harmful interference to radio communications.Operation of this equipment
in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Do not make any changes or modifications to the equipment unless
otherwise specified in the manual.If such changes or modifications should
be made,you could be required to stop operation of the equipment.
Use of shielded cable is required to comply with class A limits in Subpart B
of Part 15 of FCC Rules.
Model: CR-N300 (including WLAN Module Model ES202,FCC ID: AZD239 /
IC: 498J-239)
This device complies with Part 15 of FCC Rules and ISED's applicable
licenceexempt RSS standard(s). Operation is subject to the following two
conditions:
(1)this device may not cause interference,and
(2)this device must accept anyinterference,including interference that may
cause undesired operation of this device.
This equipment complies with FCC/ISED radiation exposure limits set
forth for an uncontrolled environment and meets the FCC radio frequency
(RF)Exposure Guidelines and RSS-102 of the ISED radio frequency (RF)
Exposure rules.This equipment should be installed and operated keeping
the radiator at least 20 cm or more away from person's body.
This transmitter must not be co-located or operated in conjunction with any
other antenna or transmitter.
FDA regulation
This product has not been evaluated by the Food and Drug Administration
(FDA)for use as a medical device.When incorporated into a system with
medical applications,FDA regulations may apply.Therefore,please consult
your legal advisor to determine whether FDA regulations apply.
Complies with
IMDA Standards
DB00671
European Union regulatory notices:
Remote Camera,Model Name: CR-N300
Warning
This is a class A product.In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
Use of shielded network cable is required to comply with Class A limits in
EN55032.
Wireless LAN Specifications
Frequency range: 2,401 MHz –2,473 MHz
Maximum output power: 9.48 dBm
For EU
Hereby,Canon Inc., declares that the radio equipment type CR-N300 is in
compliance with Directive 2014/53/EU.The full text of the EU declaration of
conformity is available at the following internet address:
http://www.canon-europe.com/ce-documentation
For UK
Hereby,Canon Inc., declares that the radio equipment type CR-N300 is
in compliance with the relevant statutory requirements.The full text of the
declaration of conformity is available at the following internet address:
https://www.canon-europe.com/ce-documentation/
Only for European Union and EEA (Norway,Iceland and Liechtenstein)
These symbols indicate that this product is not to be disposed of with your
household waste,according to the WEEE Directive
(2012/19/EU), the Battery Directive (2006/66/EC)and/or
national legislation implementing those Directives.
If a chemical symbol is printed beneath the symbol
shown above,in accordance with the Battery Directive,
this indicates that a heavy metal (Hg = Mercury,
Cd = Cadmium,Pb = Lead)is present in this battery or accumulator at
a concentration above an applicable threshold specified in the Battery
Directive.
This product should be handed over to a designated collection point,e.g.,
on an authorized one-for-one basis when you buy a new similar product or
to an authorized collection site for recycling waste electrical and electronic
equipment (EEE)and batteries and accumulators.Improper handling of
this type of waste could have a possible impact on the environment and
human health due to potentially hazardous substances that are generally
associated with EEE.Your cooperation in the correct disposal of this product
will contribute to the effective usage of natural resources.
For more information about the recycling of this product,please contact your
local city office,waste authority,approved scheme or your household waste
disposal service or visit www.canon-europe.com/sustainability/approach/.
CANON INC.
30-2,Shimomaruko 3-chome,Ohta-ku,Tokyo 146-8501,Japan
Canon U.S.A.Inc.
One Canon Park,Melville,NY 11747,U.S.A.
Tel No.1-800-OK-CANON (1-800-652-2666)
CANON EUROPA N.V.
Bovenkerkerweg 59,1185 XB Amstelveen,The Netherlands

5


L > 300 mm

0.6 N·m
M3 x 6L (4)
6


180°

7
M3 x 4L
8





2
2
2
BIM-7170-000
1
L < 100 mm
L < 100 mm
2


3



4
M4 (4)
9

10
M3 x 4L
11
© CANON INC.2021 Printed in Japan
θ
θ
θ≦±5°
1

JA
1.カメラヘッド /2.タリーランプ
*
/3.レンズ /4.赤外線リモコ
ン受光部 /5.STATUS ランプ
*
/6.POWER ランプ
*
/7.ロゴプ
レート /8.ベース /9.ゴム脚 /10.三脚用ネジ穴 /11.背面パネ
ル/12.排気口 /13.取付用板金固定ネジ穴 /14.定格銘版
*詳細は「使用説明書 重要事項・設置編 [1/2]」参 照
EN
1. Camera head / 2. Tally lamp*/ 3. Lens / 4. IR remote control receiver /
5. STATUS indicator*/ 6. POWER indicator*/ 7. Logo plate / 8. Base /
9. Rubber feet / 10. Screw hole for tripod / 11. Rear panel / 12. Air exit
vent / 13. Screw hole for fixing ceiling plate / 14. Rating label
* Refer to the "Installation Guide/Important Information" [1/2] for details.
DE
1. Kamerakopf / 2. Kamerakontrolllampe*/ 3. Objektiv / 4. Empfänger für
IR-Fernbedienung / 5. STATUS-Anzeige*/ 6. STROM-Anzeige*/
7. Logoschild / 8. Sockel / 9. Gummifüße / 10. Schraubenloch für Stativ /
11. Rückwärtiges Bedienfeld / 12. Luftauslassöffnung /
13. Schraubenloch zur Befestigung der Deckenplatte / 14. Typenschild
* Für weitere Informationen siehe „Installationshandbuch/Wichtige Informationen“ [1/2].
ES
1. Cabezal de la cámara / 2. Luz de recuento*/ 3. Objetivo / 4. Receptor de
control remoto IR / 5. Indicador de ESTADO*/ 6. Indicador de ENCENDIDO*/
7. Plancha de logotipo / 8. Base / 9. Patas de goma / 10. Orificio para
atornillar el trípode / 11. Panel trasero / 12. Salida de ventilación / 13. Orificio
para atornillar la plancha de techo / 14. Etiqueta de calificación
* Consulte la "Guía de instalación/Información importante" [1/2]
para conocer más detalles.
FR
1. tête de camera / 2. Lampe tally*/ 3. Objectif / 4. Récepteur de
télécommande infrarouge / 5. Indicateur d’état*/ 6. Indicateur d’alimentation*/
7. Plaque de logo / 8. Base / 9. Pieds en caoutchouc /
10. Trou de vis pour trépied / 11. Panneau arrière / 12. Orifice de sortie d’air /
13. Trou de vis pour plaque de fixation / 14. Étiquette constructeur
* Consultez le « Guide d’installation/informations importantes » [1/2] pour plus de détails.
IT
1. Testina della telecamera / 2. Lampada tally*/ 3. Obiettivo / 4. Ricevitore
del telecomando a infrarossi / 5. Indicatore di STATO*/ 6. Indicatore di
ALIMENTAZIONE*/ 7. Piastra del logo / 8. Base / 9. Piedini di gomma / 10. Foro
della vite per il treppiede / 11. Pannello posteriore / 12. Sfiato dell'aria / 13. Foro
per la vite di fissaggio della piastra a soffitto / 14. Etichetta di classificazione
* Per i dettagli, consultare il documento “Guida all’installazione/Informazioni importanti” [1/2].
RU
1. Головка камеры / 2. Индикатор съемки
*
/ 3. Объектив / 4. ИК приемник
дистанционного управления / 5. Индикатор состояния STATUS
*
/
6. Индикатор питания POWER
*
/ 7. Табличка с логотипом / 8. Основание /
9. Резиновые ножки / 10. Отверстие под винт для штатива / 11. Задняя
панель / 12. Выпускное вентиляционное отверстие / 13. Отверстие под винт
для крепления потолочной пластины / 14. Табличка с техническими данными
* Подробности см. в документе «Руководство по установке/Важная информация» [1/2].
ZH
1. 摄像机头部 / 2. 摄像指示灯
*
/ 3. 镜头 / 4. 红外线遥控接收器 / 5. STATUS
指示灯
*
/ 6. POWER指示灯
*
/ 7. 标志牌 / 8. 底座 / 9. 橡胶脚垫 / 10. 三脚架
螺孔 / 11. 后面板 / 12. 排气口 / 13. 吊顶板固定螺孔 / 14. 额定铭牌
* 有关详细信息，请参阅“安装指南/重要信息[1/2]”
1
2
3
4
5
6
7
8
1
設置の手順は天吊り設置で説明します。据え置き / 机上 / 三脚の設置では必要に応じて参照してください。
EN Installation procedure is explained using the ceiling mount as an example. Refer to this section as reference if
necessary, for standing mount, desktop and tripod mount.
DE Der Installationsvorgang wird anhand der Deckenmontage als Beispiel erläutert. Ziehen Sie diesen Abschnitt
bei Bedarf zur Referenz heran– bei Standmontage, Desktop und Stativmontage.
ES El procedimiento de instalación se explica con el montaje en techo como ejemplo. En caso necesario, consulte
esta sección como referencia para el montaje de pie, en escritorio y el montaje en trípode.
FR La procédure d’installation est expliquée en prenant le support de plafond pour exemple. Si nécessaire,
consultez cette section à titre de référence pour le montage sur pied, sur table ou sur trépied.
IT Per la spiegazione della procedura di installazione sarà utilizzata come esempio l'installazione a soffitto.
Consultare questa sezione, se necessario, per montaggio con staffa, montaggio su tavolo e montaggio su
treppiedi.
RU Процедура установки рассматривается на примере монтажа на потолке. Обращайтесь к этому разделу
для справок по мере необходимости при монтаже на полу, на столе или на штативе.
ZH 使用天花板安装作为示例对安装步骤进行说明。对于直立安装、桌面和三脚架安装，必要时请参考本节。
JA
2
スリットから設置用落下防止ワイヤーを通し (

)、裏側にあるフックに引っか
けます (

)。
ワイヤーの外し方：フック固定ネジ (★) を緩め ( )、ワイヤーをフックから逃
がす方向に上下させて設置用落下防止ワイヤーを外してください ( )。
EN Pass the Camera-to-Mount Safety Wire through the slit

and attach it to the
hook on the rear side

.
How to remove the wire: Remove the Camera-to-Mount Safety Wire by loosening
the hook fixing screw (★) and moving the wire upward and downward to
release from the hook .
DE Führen Sie das Sicherungsseil zwischen Kamera und Halterung durch den
Spalt

und befestigen Sie es an dem Haken auf der Rückseite

.
So entfernen Sie das Seil: Entfernen Sie das Sicherungsseil zwischen Kamera
und Halterung durch Lösen der Hakenbefestigungsschraube (★) und Auf-
und Abbewegen des Seils, um es vom Haken zu lösen .
ES Pase el cable de seguridad de la cámara al montaje a través de la hendidura

y átelo al gancho situado en la parte posterior

.
Cómo retirar el cable: Para retirar el cable de seguridad de la cámara al
montaje, afloje el tornillo para fijación del gancho (★) y mueva el cable hacia
arriba y hacia abajo para soltarlo del gancho .
JA FR Faites passer le fil de sécurité reliant la caméra au support dans la fente

et
fixez-le au crochet situé à l’arrière

.
Pour retirer le fil: Retirez le fil de sécurité reliant la caméra au support en
desserrant la vis de fixation du crochet (★) et en déplaçant le fil vers le haut
et vers le bas pour le dégager du crochet .
IT Passare il cavo di sicurezza dalla telecamera al supporto di montaggio nella
fessura

e collegarlo al gancio nella parte posteriore

.
Come rimuovere il cavo: rimuovere il cavo di sicurezza dalla telecamera al
supporto di montaggio allentando la vite di fissaggio del gancio (★) e
muovendo il cavo verso l'alto e il basso per staccare il gancio .
RU
Проведите предохранительную проволоку, соединяющую камеру с
креплением, через прорезь

и прикрепите ее к крючку на задней стороне

.
Порядок снятия проволоки: снимите предохранительную проволоку,
соединяющую камеру с креплением, ослабив крепежный винт крючка
(★)
и перемещая проволоку вверх и вниз, чтобы высвободить ее с крючка .
ZH 将安装用安全钢丝从细缝穿过(

)，然后将其挂在后方的挂钩上(

)。
如何取下钢丝：通过松开挂钩固定螺丝(★) ( )，然后上下移动钢丝以从挂钩上
脱离来取下安装用安全钢丝( )。
Φ153
153
46
4 x 4.5
4 x 8.5
Φ5
8 x (R)
32.9
87.1
171
83.5
170°
171
77
170°
Φ154
1/4-20UNC
137
178
1
217
30°
100°
R80
Unit: mm

109
13
12
4
11
14
9
Serial_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
MAC_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
170°
171
77
170°
Φ154
137
178
1