canty KD-51 Easycut Operation instructions

●Please read this instruction carefully before operation
●Take special care on safety prompts in these instructions so as to avoid injury to yourself,
other people and objects.
●Please follow the guidelines in these instructions to avoid damage to the tool
Caution 1: Use outdoor or in well ventilated space.
Caution 2: Don't touch hot wire when working
Original instruction
KD-51Easycut
Hot Wire Foam Cutter
Operating instruction
www.hilltop-products.co.uk - Tel: [phone] - Email: [email protected]

Introduction
The KD-51 Hot Wire Cutter is a professional-grade hot cutting machine for foamed plastics.
The KD-51 Hot Wire Cutter heats up in seconds and gives the Button switch.
Recommended Use
Expanded Polystyrene (EPS), Extruded Polystyrene (XPS), can be
easily cut with cutting procedures.
Wire Installation
Hot Wire
Plywood Flat Board
Aluminium Bow
Middle Plate
Back Stand
Right Side Plate
Side Guider Ruler
Guider Ruler Front Stand
(4-100cm,0º-75º)
Transformer
One pull the 2pieces of spring with drag hook at same time(Not pull overdo), and partner put up the wire
to the springs.
Caution 1: Excessive power output and heat generation may cause the damage to the tansformer. Use only the
power output for proper cutting. The wire does not need to be red hot to move through foamed plastics.
Original instruction
NOTE: Always unplug the power cord
of the KD-51 Hot Wire Cutter before
installing or removing the wire. Allow
sufficient cooling time for wire and wire
holders (Springs)

Plug In
Frame
Spring
Vertical degree
(0º-75º)
Shapes to be cut
Rectangle
Ladder-shaped
Triangle
Bevel cut
Technical Date
Power Cord Length
2.0M(Transformer to Power Suplly); 1M(Transformer to Plug in of Frame)
Intermittent Operation
15s on / 45s off
Size
Transformer
1700X430X170mm
40V/200W/230V(110V) IP54
Thermostat built inside
Guider Ruler
Wight
1320mm
330mm
1000mm; 0-75º
17.4Kg
1.Setting the Vertical Degree at 0º.
2.Setting the Guider Ruler at needed degree
3.Cutting according to the scale of the ruler.
1.Setting the Vertical Degree needed degree.
2.Setting the Guider Ruler at 0º
3.Cutting according to the scale of the ruler.
Model Number
KD-E10-1370
Max. Cutting Length
Max.Cutting Height
Original instruction
1.Setting the Vertical Degree at 0º.
2.Setting the Guider Ruler at 0º.
3.Cutting according to the scale of the ruler.

─Consider work area environment
─Do not expose tools to rain.
─Do not use tools in damp or wet locations
─Keep work area well lit.
─Do not use tools in the presence of flammable liquids or gases
─Keep other persons away
─Do not let persons, especially children, not involved in the work touch the tool or the
extension cord and keep them away from the work area
─Store idle tools
─When not in use, tools should be stored in a dry locked-up place, out of reach of children
─Do not abuse the cord
─Never yank the cord to discounnect it from the socket.
Keep the cord away from heat, oil and sharp edges.
─Disconnect tools
─When not in use, before servicing and when changing hot wire,
disconnect tools from the power supply.
─Warning
─The use ofn any hot wire other than one from Original production
may present a risk of machine damaged
─Please have your tool repaired by a qualified person
Transformer Assembly Front Stand Assembly Back Stand Assembly
A
M6 X 20
4 X
Right side Plate Assembly
A
Original instruction
Kirkstead Way
Golborne
Warrington
WA3 3PY