Capricorn RC LABC-801 User manual

Instruction Manual rel. 1.
3
(12/2012)

Step 0.1 Capricorn RC
- Symbols -
Made in Italy
This radio control model is not toy.
First time builders should seek the advice of experienced modellers before beginning assembly and/or if they do not fully
understand any part of the construction.We highly advise to read the instruction manual before assembly, and to always
keep it at hand for reference. Take care before operating this model; you are responsible for its assembly and safe
operation. The extreme performance of this model could be understimated by inexpert drivers and could damage objects
and/or people. Assembly this kit only in places out of children's reach!
CAPRICORN RC is not responsible for any damage or harm caused by improper use or assembly.
CAPRICORN RC and its distribution network are not responsible for any damage caused by shipping or handling.
Eventual parts missing from the kit or flawed must be reported within two weeks of purchase to your local hobby
shop or distributor. For best performance, we highly advise to only use original authentic CAPRICORN RC parts.
For customer support and service please contact your local hobby shop or agent from whom you purchased this item.
Contents of box may slightly differ from the pictures shown. Construction tools, body, fuel, radio system and servo,
engine, muffler and battery pack are NOT INCLUDED unless otherwise stated.
WARNING
L/R
Symmetrical
Mounting
2x
Assemble as many
times as specified
1 2
3 4
Assemble in the
specified order
Note:
TEXT....
Be Careful
2

Step 0.2 Capricorn RC
- Tools & Equipment -
Made in Italy
Tools needed for assembly (NOT INCLUDED)
Parts for model completion and Start (NOT INCLUDED)
Exhaust System
Engine Air Filter & Oil Steering & Throttle
Servos
Receiver RX Battery Pack
Transmitter Battery Charger
Also required: Starting Box - Nitro fuel - Fuel bottle - Glower - Plycarbonat body
Hex Wrench
1,5/2/2,5/3mm Reamer Wrench Glowplug
& Cluthnut Cutter Pliers Adjustable Pliers
Box Wrench
5mm Glass or Vinyl
Tape
3

Step 0.3 Capricorn RC
- Screws Chart -
Made in Italy
Bag S
Bag S
Bag S
Bag S
M2,5x8
M3x5
M3x6
M3x8
M3x12
M3x6
M3x8
M3x10
M3x12
M3x16
M2,5x10
Bag S
Bag S
Bag S
Bag S
Bag S
Bag S
Bag S
Bag S
Bag S
Bag S
Bag S
Bag S
Bag S
Bag S
Bag S
Bag S
Bag S
Bag S
Bag S
Bag S
Bag S
Bag D
Bag S
Bag P
Bag S
Bag S
Bag S
M3x8 Flanged
M3x12 Flanged
M3x3
M3x5
M3x8
M4x4
M4x6
M4 Nylon lock
E-Ring n3
E-Ring n8
C-Ring n14
Washer 8x11x0,5
Pin 3x9,8
4
Bag S
Bag P
Bag P
C-Ring n12
M4x10
M2,5x3
Pin 3x19,8
Pin 3x21,8
Washer 12x15x0,5
Washer 3x6x2
M3x16
M4x8
M4x8
M4x12
Bag S
E-Ring n2,5

Parts List
Rif. n° Code Bag
1 1 Cap16066-bs D
2 1 Cap14044 D
3 1 Cap16066-bs D
4 1 Cap16016 D
51Capshockori D
6 1 Capshockori D
71 Cap16003 D
8 1 Cap14033 D
9 1 Cap14036 D
10 1 Cap16085 D
11 1 Cap14042 A
12 1 Cap14041 A
Step 1.0 Capricorn RC
- Shock absorbers -
Made in Italy
5
11
5
7
6
8
10 9
4
12
4x
Front 2x
Rear 2x
Oil
3x1,78
Note:
Front Short 2x
Rear Long 2x (Code Cap16016L)
kit
12
12
Front
Rear
1
2
3
Important Note:
Do not force screwing
to ball joints damage

1 1 Cap171215 D
2 1 Cap16027 D
3 1 Cap 508 BOX
41Cap14030 D
Parts List
Rif. n° Code Bag
Step 1.1 Capricorn RC
- Shock absorbers -
Made in Italy
6
5 Initial Setting
8 Initial Setting
Front 2x
Rear 2x
1
2
3
4
Oil
Front
12x1,5
Rear
4x

Parts List
Rif. n° Code Bag
1 1 Cap 2023 P
2 1 Cap 2140 S
3 1 Cap 2103 O
4 2 Cap 2129 P
52Cap 2012 B
6 2 Cap 2002 W
Step 2.0 Capricorn RC
- Rear solid axle -
Made in Italy
7
1
2
3
4
5
6
5
6
3x21,8 Pin
12x18x4
12x18x4
Z46
4
or
--
--

Parts List
Rif. n° Code Bag
1 1 Cap 2022 P
2 1 Cap 2101 O
3 1 Cap 2061 O
41Cap 2130 P
52Cap 2012 B
6 2 Cap 2057 R
72Cap 2117 C
8 2 Cap 2003 W
Step 3.0 Capricorn RC
- One way front axle -
Made in Italy
8
One way oil
12x18x4
Z23
6
5
4
1
8
7
2
3
One way oil
6x12x2

Parts List
Rif. n° Code Bag
1 2 Cap 2119 E
2 1 Cap 2060 O
3 1 Cap 2099 O
4 2 Cap 2006 S
52Cap17010 S
6 1 Cap 2062 O
71Cap 2102 O
8 1 Cap16083 M
9 2 Cap16020 B
10 1 Cap16060 M
11 2 Cap17030 S
12 1 Cap 2021 P
13 1 Cap 2055 P
Step 4.0 Capricorn RC
- Middle Shaft Holder -
Made in Italy
9
Initial Setting
REAR
FRONT
B
A
To tighten front belt To loosen front belt
1
4
3
7
6
2
5
6x13x5
M3x6
Thread Lock
Z18
Z29
M4x4
Thread Lock
12
13
9
11
10
8
Option Z30
Code Cap2103-30
(Only M3-435 Belt)

Parts List
Rif. n° Code Bag
1 1 Cap 2020 C
2 2 Cap 2128 S
3 2 Cap 2068 R
4 2 Cap16011 C
52Cap16031 C
6 2 Cap17021 S
72Cap17006 S
Step 5.0 Capricorn RC
- 2 Speed gear -
Made in Italy
10
3
6
4
5
1
2
M2,5x10
Important Note:
adjust the M2,5x10 screws in equal mode
7M3x3
Note:
Tighten screw gently until just
before a small gap appears
between the clutch shoes.

Parts List
Rif. n° Code Bag
1 1 Cap 2059 E
2 1 Cap2051-57 R
3 3 Cap17038 S
4 1 Cap 2058-B C
51Cap2050-61 R
6 3 Cap17031 S
71Cap 2127 P
8 2 Cap 2015 B
Step 5.1 Capricorn RC
- 2 Speed gear -
Made in Italy
11
4
7
5
6
2
3
8
1
8
M3x5
8x12x3,5
M3x8
8x11x0,5
8x12x3,5
Z57
Z61
Note:
Clean oil residue
from inside part

1 1 Cap16014 E
2 1 Cap16065 M
3 1 Cap 2107 M
4 1 Cap16033 E
51 Cap171015 E
6 1 Cap16028 E
72Cap16019 B
8 1 Cap16055 E
9 1 Cap2124-11 R
10 2 Cap17030 S
11 1 Cap17029 S
12 3 Cap16086 A
Parts List
Rif. n° Code Bag
Step 6.0 Capricorn RC
- Servo Saver -
Made in Italy
5x8x2,5
5x8x2,5
M3x6
Thread Lock
M3x6
Thread Lock
0,5:1,0
11 Initial Setting
Ackermann Inserts
Oil
10
9
3
12
2
1
7
7
11
12
4
5
6
8
10x1,5
10
12
12
Option
Important Note:
Do not overtighten preload adjust nut
Servo danger damage
5,8 ball

Parts List
Rif. n° Code Bag
1 1 Cap 2029 R
2 2 Cap 2013 B
3 2 Cap15010 E
42Cap16012 E
52Cap16018 B
6 2 Cap 415 B
72Cap17026 S
Step 7.0 Capricorn RC
- Belt Tensioner Set -
Made in Italy
13
2:1 Scale larger picture
2
3
1
6
5
4
7
3x6x2,5 Flanged
5x10x4 Flanged
5x10x4
M3x12
---
ATo loosen side belt
BTo tighten side belt

1 1 Cap 2026 R
2 2 Cap 2149 B
3 1 Cap 2078 P
4 1 Cap 2126 P
51Cap 2129 P
6 2 Cap16004 A
72Cap 2151 P
8 1 Cap 2065 P
9 1 Cap17006 S
10 1 Cap 2069 P
11 1 Cap 2140 S
Parts List
Rif. n° Code Bag
Step 8.0 Capricorn RC
- Rear Suspension -
Made in Italy
14
8
9
3
10
2
1
5
4
11 6
7
3x21,8 Pin
M3x3
12x15x0,5
12x21x5
Initial position for
Tire Offset
.
Pivot Balls must move freely
2x L/R
Short type

Parts List
Rif. n° Code Bag
1 1 Cap 2010 N
2 1 Cap17011 S
3 2 Cap 2074 M
4 2 Cap14038 R
51Cap 2093 R
64Cap17031 S
Step 8.1 Capricorn RC
- Rear Suspension -
Made in Italy
15
M3x8
Thread Lock
M4x6
Thread Lock
There are four eccentric holders
for seven different setting:
-1,5/-1/-0,5/0/+0,5/+1/+1,5
Initial setting
Rear up roll center insert
0
M3x201 Belt
ABC
Adjusting the rear belt tension
A= To loosen
B= Default position
C= To tighten
3
456
2
1
Note:
Hard Thread Lock
on the 3x9,8 pin
Type A
Type B
Code Cap 2095

Parts List
Rif. n° Code Bag
1 1 Cap 2035 R
2 1 Cap 2018 S
3 1 Cap 2094-S F
42Cap16086 A
54Cap17030 S
6 1 Cap 2085 L
Step 8.2 Capricorn RC
- Rear Suspension -
Made in Italy
16
3x56
M4x10
M3x6
Initial position
2x L/R
1
2
6
4
5
3
1,5 Initial down stop setting
5,8 ball
SX
DX
Note:
Remove as shown
on DX and SX arm

1 1 Cap 2098 R
2 1 Cap 2121 A
3 1 Cap 2115 P
4 1 Cap 2036 R
51Cap 2086 L
Parts List
Rif. n° Code Bag
Step 8.3 Capricorn RC
- Rear Suspension -
Made in Italy
17
3x40
Initial setting
2x L/R
7,0 ball
SX
DX
1
2
3
4
5
Rear camber setting
L/R
--
2
With 2 hex wrench:
Turn clockwise for less camber
Turn counterclockwise for more camber
Note:
Flare on top side

Parts List
Rif. n° Code Bag
1 1 Cap 2093 R
2 4 Cap14038 R
3 6 Cap17031 S
Step 8.4 Capricorn RC
- Rear Suspension -
Made in Italy
18
1
3
2
M3x8
Thread Lock Code Cap 2095
Type A Type B

Parts List
Rif. n° Code Bag
1 4 Cap14038 R
2 1 Cap 2113 M
3 1 Cap 2109 M
41Cap 2114 BOX
51Cap 2089 F
6 6 Cap 2146 S
74Cap17026 S
Step 8.5 Capricorn RC
Made in Italy
19
- Rear Suspension -
There are four eccentric holders
for seven different setting:
-1,5/-1/-0,5/0/+0,5/+1/+1,5
Rear roll center insert
Initial setting
0
5
2
7
6
3
4
1
M3x12
Thread Lock
M4x8
Thread Lock

Parts List
Rif. n° Code Bag
1 2 Cap 2132 P
2 2 Cap17043 S
3 2 Cap 2143 S
42 Cap 2028 R
5 4 Cap 2040 B
6 4 Cap17023 S
72Cap16081 P
8 4 Cap14042 A
9 2 Cap16086 A
10 2 Cap17032 S
Step 8.6 Capricorn RC
Made in Italy
20
- Rear Suspension -
38 : 38,5
100°
L/R 2x
Left move side
L/R
3x6x2
M3x10
M3x16
5,8 Ball
M3x8
Inital Setting
1
2
6
5
4
3
10
9
8
7
4,5Rearpivot
3,0Frontpivot
4,5Rearpivot
3,0Frontpivot
Grease