CARBONE ACS User manual

ACS & TCS
Electronic Weighing Scale Manual
CALIBRATION AND FUNCTION SETTINGS
TRANSPORTATION AND STORAGE
Avoid shock and dampness during transportation
Avoid strong sunshine and rain during storage.
ATTENTION
Please read this instruction manual carefully before you
use the scale.
If it has not be used for long time, please recharge it once
2 months at least, and keep the power switch on “off”
status to avoid discharge of accumulator.
LCD of the scale must to be operated under rich light,
you are advised to select product with backlight under
low light condition.
Avoid collision when you put the weighting object on
the scale.
It is strictly prohibited to use strong chemical solvent
to clean the surface.
Please clean the scale with dry or wet dishcloth.
Washing it with water is strictly prohibited.
Please doesn't use the same power equipment will
influence the weighing.
CAUTION
If the price window displays “---Lb---” when the weight
window displays “------”, it means the voltage of the
accumulator is low. Under this condition, you can use
the scale in a short time, but you should plug in the AC
plug as soon as possible to recharge the accumulator,
please recharge the accumulator for more than 12hours.
The battery and pan is not included in free maintain
warrant.
This scale needs to be periodically served to professional
institutions for calibration, such as in the case of trade
settlement disputes, the user assumes responsibility.
The weight window displays”------”with continuously alarm
sound when the weight over 100%FS+9d.
If the voltage of the accumulator is low, the price window
displays “---Lb---”while the weight window displays zero
(The price display will recover to normal when it is loaded).
Under this condition，you can use the scale in a short time,
but you should plug as soon as possible to recharge the
accumulator.
The weight window displays “FUHHH” or “FULLL” when the
zero weight is higher or lower than the permitted range.
How to calibrate the scale?
Press 7616 press tare press 3 put 5kg or 10kg
calibration weight on plate insert corresponding weight
press tare, that's all, finish. Press ADD or Turn off the
switch to exit.
How to set MAX capacity and accuracy?
Press 7616 press tare press 1 to change the MAX
capacity / press 2 to change the accuracy press 0 to save
it, that's all, finish.
How to open the units change function?
Press 168press tarepress 166press tare, then,
press CHG/SET key to change kilograms/pounds.
Press 168press tarepress 155press tare to close
the function.
How to set the STABLE/HOLD function?
Press 168press tarepress 37press tare, open it.
Press 168press tarepress 38press tare, close it.
How to set the zero position?
Press 168press tarepress 50press tarepress
ADDpress tare, that's all, finish.
How to set UNIT price window decimal?
Press 168 press tare press 30 press tare, no decimal.
Press 168press tarepress 31press tare, 1 decimal.
Press 168press tarepress 32press tare, 2 decimal.
How to store your phone number?
Press 168press tarepress 111press tarepress C
insert your numberpress tare, that's all, finish.

SPECIFICATION
Rechargeable accumulator inside, you can use the scale
during recharging.
Auto zero-setting when switch on the scale.
Auto zero-tracing.
Working temperature range:0℃~+40℃
Power supply: AC 200V（ ±10%）/50HZ，DC 4V/4Ah
(Rechargeable accumulator inside).
Relative humidity:≤85%RH
KEY DESCRIPTION
PRODUCT DESCRIPTION
*The scale must to be placed on a stable and flat platform.
You should adjust four underside bolt to make the scale
in horizontal position, the switch on the power(put on
special weighing pan first if necessary).The scale can’t
be used in tare state for long time, otherwise the auto
zero-tracing function will be invalid, and the zero point
will excursion.
【0】 ~【 9】key: Input the unit price, from the right to the
left circularly, press any number key to clear the former
unit price after 3 seconds, meanwhile this number is
inputted.
【Zero/Tare】key: Set the weight window to zero. (Range
of tare setting: weight：≤1/3F.S)
*Press this key, set the weight window to zero, and the
“Zero/Tare” symbol is appeared.
*Take away the weight object, the weight window displays
negative, press【Zero/Tare】key again, set the weight
window to zero, and the “Tare” symbol is disappeared.
【 . 】key: radix point press, input the integer part before
press and decimal fraction after press the key.
【ADD】key: Press this key to accumulate the money，
and the “ADD” symbol is appeared , the weight window
displays “Add”, the unit price window displays “----”, “-----”
means the accumulated times, the price window displays
the total money,. Press any number key to exit from this
state with the memory of accumulating held, and then the
scale comes back to weighing state and waits for the next
accumulating.
【C】key: Press this key to clear the inputted unit price
under weighing state.
【 】key: This key is the back-light key. Press this key to
turn off the backlight or turn on the backlight. Starting
up default is to display the backlight automatically.
【 】key: This is the customer service phone. Press this
key, three windows show "customer service phone" and
press any key to exit.
【 】key: This is the counting key, press this key, put a
number of products, input the number of products, press
this key to set sampling to complete, can achieve counting
function. Press this key again to exit.
【SET】key:
*Press this key to enter change function (it’s no use when
price window display zero or “------“), when the weight
window display “—PAY—“, unit price and price window
display “----“, clew to enter the price needed to charge.
Then press “0-9” number key to enter the charged price
and displayed in the unit price window, when the price
entered is higher than original counting price, the price
window will display the present change number. In this
state, press ”clear” key can clear the inputted charge price
and the unit price and price window will show “-----“ to clew
to enter new charge price. Press the【 SET】key again, the
scale will exit change function to be in weighing state.
*Long hold down this key, The amount window display
"SAVE", input unit price, save in【 M1】
1
2
3
4
10
7
5
6
9
8
12
34
56
78
Adjustable feet
Applicable to uneven surface
Weighing pan
Tray plate / Flat plate
Folder
90 degree folding
Fence
Detachable
Switch
With waterproof cover
Power cord interface
Connect to the power
Weight window
Display the weight of the object
910 Total window
Show total amount
Unit price window
Display the entered unit price
Function button
Enter unit price and settings
Store
V
Number
buttons
Clear
Storage
unit price Set
Deduct tare
Cumulative
amount
Current battery
voltage
Adjust brightness
Change / Set
Contact number
V
Number
buttons
Clear
Storage
unit price
Deduct tare
Cumulative
amount
Current battery
voltage
Adjust brightness
Counting
function