Carilex Coziny 100 User manual

1AIR ALTERNATING PRESSURE MATTRESS SYSTEM
English
Congratulations and thank you for purchasing this Carilex anti-decubitus
mattress system. PLEASE READ THIS OPERATION MANUAL
CAREFULLY BEFORE SETTING UP AND USING THE DEVICE.
Pay special attention to the warnings and other safety information. Use
genuine Carilex components are essential for optimal performance. If you
do not fully understand all the instructions, safety precautions, and
warnings, do not use this device. In case you have questions, please
contact your local Carilex distributor.

LAUNAMNOITAREPO003/002/001YNIZOC 2
English
Section Description Page
1.0 Indications ...................... 3
2.0 Safety Precautions .......... 3
3.0 Warnings ......................... 4
4.0 System Package .............. 4
5.0 Features .......................... 4
6.0 Mattress and Power Unit
Installations .................... 5
7.0 Program Settings ............ 6
8.0 Patient Transfer and
Transport ......................... 6
Section Description Page
9.0 Cleaning Instruction ....... 6
10.0 Routine Maintenance ...... 7
11.0 Troubleshooting .............. 8
12.0 Returns for Service ....... 10
13.0 Warranty ........................ 10
14.0 Product Specifications ... 10
15.0 Environmental protection..11
Table of
Contents

3AIR ALTERNATING PRESSURE MATTRESS SYSTEM
Indications
This air alternating mattress system is
designed for patients who endure
pressure ulcer and potential patients who
wish to reduce the likelihood of pressure
ulcer. This device is intended to treat
and prevent pressure ulcers by
facilitating blood circulation and
decreasing pressure of each tissue's
contact area. Always consult a physician
or health professional before using this
English
mattress system.
Contraindications
Certain patient conditions are not
suitable for using this type of device
such as fracture of instable vertebrae and
illness of instable vertebrae. Always
consult a physician or health
professional before using this device.
The use of this system does not replace
the regular repositioning, monitoring,
and nursing of the patient.
2.0 Safety Precautions
(1) To ensure proper operation, please
inspect and verify all parts are setup
properly and anchor securely. Do not
place anything on top of the power
unit. Make sure power cord is underneath
bed frame and free from hazard.
(2) It is recommended to limit bed linens
to a single layer in order to allow the
moisture escape efficiently through
the coverlet. Only "breathable"
incontinent pads are recommended
for use with this mattress system.
(3) Avoid using this device near open
flames, lighters, or cigarettes.
Flammability hazard exists. This
device draws air from the
surrounding. Thus, cigarette smoking
may damage internal component.
(4) This system should disinfect
thoroughly between patients to avoid
cross contamination.
(5) Verify patient weight does not
exceed bed frame, bed rails, and this
mattress system's weight capacity.
Attention! Please read
enclosed document
thoroughly
Declaration of Conformity
to Medical Device
Directive
International Electronics
Approval
Do not immerse power
unit in liquid or spray
liquids directly on power
unit
Type B Equipment
1.0 Indications

3.0 Warnings
(1) Use this mattress with proper side
rails to ensure the gap between the
side rail and top of the mattress is
small enough to prevent patient from
getting his or her head or neck into
the gap. Fail to do so could result in
serious patient injury.
(2) DO NOT disassemble the power unit
if you are not a qualified technician.
Please contact your local distributor
for all service.
(3) This product is NOT AP/ APG protected.
(4) Re-position the patient regularly is
still necessary when using this
mattress.
(5) Operating, transportation, and storage
conditions:
Temperature: 5ʨ- 40ʨ
Humidity: 15% - 60%
CAUTION: ENSURE THAT THERE
ARE NO PROTRUDING OBJECTS,
SHARP POINTS OR BED SPRINGS
UNDER THE MATTRESS AS THESE
COULD PUNCTURE THE AIR CELLS.
4.0 System Package
Power Unit Package
* Power unit x 1
* Power cord x 1
* Operation manual x 1
Mattr ess Package
Mattress unit with coverlet x 1
5.0 Features
Control Panel Features
See Figure 5a on page 5.
power LED
The green power LED will light when
the main power rocker switch on the
right side panel is turned on
alarm LED
This low pressure alert notifies medical
staff the mattress has insufficient
pressure. Audible alarm will sound for
15 seconds at each cycle and the
indicator will stay on until the problem
has been solved.
pressure monitoring LED
Power unit features an integrated
pressure senor which can monitor the
mattress' internal pressure 24 hour to
achieve optimal internal pressure and to
ensure maximum pressure relief. LED
indicates the system is monitoring the
mattress' internal pressure while the
compressor is inflating.
Comfort Knob
Simply turn the knob from min. to max.
to adjust the mattress internal pressure.
The scale is only an approximation.
Please adjust the pressure setting if the
mattress is too soft or firm to suit each
patient's comfort. Caregivers should
always perform a hand check by placing
their hands underneath patient's pelvis
area to check if there is sufficient air
support to ensure the patient is not
bottoming out.
English
OPERATION MANUALCOZINY 100/ 200/ 300 4

Right Side Panel Features
See Figure 5b
Rocker Switch (1)
Power unit's main power switch.
Couplers (2)
Quick release couplers are used to
secure mattress air hoses to power unit.
Power Receptacle (3)
Insert power cord firmly into receptacle.
Rear Panel Features
See Figure 5c
Convenient Handle (1)
It provides additional gripping surface
for user to carry the power unit.
Hanging Hooks (2)
Hanging hooks are designed to hang the
power unit on almost any foot board.
Fuse (3)
Fuse holder can be opened for
maintenance.
Air Filter and Filter Cap (4)
Carilex recommends that the filter to be
clean or replace once a month to ensure
optimal performance of the power unit.
6.0 Mattress and
Power Unit
Installations
(1) Place Carilex mattress on top of the
original mattress with the logo at foot
end. Secure the mattress by using
elastic straps for Coziny 200 and 300
if needed. Please verify all bed
English
5AIR ALTERNATING PRESSURE MATTRESS SYSTEM
Control Panel Features (Figure 5a)
1
2
1
3
4
2
3
Right Side Panel Features (Figures 5c)
Right Side Panel Features (Figures 5b)

functions are working properly
without interference before
proceeding to the next step.
(2) Secure the power unit onto the foot
board using hanging hooks.
(3) Firmly connect the mattress' air hose
couplings to the quick release
couplers on the power unit's air
outlet.
(4) Plug the power unit into a wall outlet
and turn on the main power rocker
switch on the right side panel to
inflate the mattress system.
(5) Turn the comfort knob on the power
unit's control panel to maximum
setting to shorten the initial inflation
time if needed.
(6) Wait for approx. 15 minutes or less
for the mattress to inflate fully.
7.0 Program Settings
(1) Center the patient on the mattress.
Adjust the mattress' internal pressure
according to the patient weight by
using the comfort knob on the
control panel of the power unit. If
the patient feels the mattress is too
soft or firm, increases or decreases
the mattress' internal pressure by fine
turning the comfort knob one
increment at a time and wait for the
system to stabilize before making
another change until a comfortable
state is achieved.
(2) Caregivers should always perform a
hand check by placing their hands
underneath patient's pelvis area to
check if there is sufficient air support
to ensure the patient is not bottoming
out.
(3) IMPORTANT: TUCKING THE
SHEET IN TIGHTLY REDUCES
THE EFFECTIVENESS OF THE
SYSTEM.
8.0 Patient Transfer
and Transport
Transfer
It is recommended to have the mattress
system at maximum weight setting
during transfer. Make sure the bed is
secured before proceeding.
Transport
If a transport occasion comes up, two
options are available: (1) Detach the
mattress' air hose couplings from the
power unit's quick release couplers and
connect the two air hose couplings
together to retain air in the mattress and
the mattress will stay inflated for approx.
2 hours. (2) Unplug the power unit's
power cord from the wall outlet and the
mattress should stay inflated for approx.
40 - 50 minutes. To resume normal
operation, please follow 7.0 Program
Setting.
9.0 Cleaning
Instruction
Air mattress and power unit must be
cleaned thoroughly between patients to
English
OPERATION MANUALCOZINY 100/ 200/ 300 6

avoid cross contamination. The
following is a suggested guideline, but
local infection control policies should be
followed as well.
Regular cleaning can be performed at
bedside with disinfectant and water
followed by drying with a clean dry
cloth. Use only mild detergents and
water to clean the coverlet and the
mattress. Any appropriate NON-
PHENOLIC cleaning agent may be used
for heavy soiling with urine, blood or
other body fluids. Please ensure air
mattress and coverlet are completely dry
before letting the patient laying on the
surface again.
The recommended wash temperature is 71ʨ.
At 95ʨ the shrinkage rate is 1% higher and
the color might run insignificantly.
Do not use electric or tumble dryers.
Do not iron.
WARNING! Always unplug the power
unit before cleaning. Routine cleaning of
power unit can be done by wiping down
with damp cloth using disinfectant and
water. Never spray liquids directly on
the unit itself.
10.0 Routine
Maintenance
Remove air filter from the real panel of
the power unit by opening up the filter
cap to clean or replace the air filter.
Inspect the filter for dirt or dust and
clean it with mild soap and water.
Reinsert the dried air filter after cleaning
and ensure the cap is secure. Replace
with genuine air filter once a year is
recommended and compressor every
two year is strongly suggested to
prolong system lifetime.
Only disinfected and dry systems are to
be stored. Disconnect the air hoses from
the power unit. Roll up the mattress
starting from head end and working
down toward the foot end. Use the
straps to fix it.
English
7AIR ALTERNATING PRESSURE MATTRESS SYSTEM

LAUNAMNOITAREPO003/002/001YNIZOC 8
11.0 Troubleshooting
English
Problem
1. Power unit does
not function.
2. Low pressure alert
does not go out in 30
sec. after systems
start.
3. alarm LED is lit
during operation.
Inspection Procedure
Check if power cord is firmly
plugged into wall outlet.
Check if power switch is in
ON position.
Check if power surge shuts
down power unit.
Make sure there is no power
failure.
Power unit does not respond
to possible solutions.
Possible control failure.
Check if there is leakage in
air tubes* or air cells.
Possible Solutions
Secure power cord into wall
outlet.
urn power switch to ON
position.
A power surge may overload
the circuitry temporarily.
urn the unit off and check
the fuse for damage. Turn
the unit ON again with
normal procedure.
Please contact your
authorized local distributor
for assistance.
Please contact your
authorized local distributor
for assistance.
Please contact your
authorized local distributor
for assistance.

English
9AIR ALTERNATING PRESSURE MATTRESS SYSTEM
4. Power unit is
working, but mattress
replacement is not
inflating.
Or/and
Bottoming out is
occurring.
Or/and
Patient leaves a deep
dent at the contact
area which does not
return back to its
original shape (worn
down by the patient)
5. Patient is not
getting pressure relief
due to system failure
(reddening of skin).
Verify if CPR latch is properly
inserted.
Check if mattress' air hose
couplings are properly
connected to power unit's
quick release couplers.
Verify if patient weight setting
is correct.
Inspect air filter for dust.
Lift mattress coverlet up to
check if air cells are connected
correctly.
Lift mattress coverlet up to
check if air tubes are kinked
or obstructed.
Check if air cells are cut or
cracked.
Connect CPR latch securely.
Secure air hose couplings
firmly into place.
Increase or decrease weight
setting until appropriate
pressure is reached.
Clean or replace air filter.
Make sure all air cells are
properly linked to air supply.
Check and adjust air tubes'
positions.
Replace with genuine spare
parts or contact your local
distributor.
Contact your physician and/
or nursing service immediately.
* Air tube is referring to the mean of directing air flow from the power unit to each individual air cell.