Carlisle CC2036DP User manual

A
AS SS SE EM MB BL LY YI IN NS ST TR RU UC CT TI IO ON NS SF FO OR RT TR RA AN NS SP PO OR RT TC CA AR RT T
D
DO OO OR R& &L LO OC CK KA AC CC CE ES SS SO OR RY YK KI IT T
P.O. Box 53006
Oklahoma City, Oklahoma 73152-3006
[phone] • FAX [phone]
1-800-654-8210
www.carlislefsp.com
European Distribution Center:
Edisonstraat 84, P.O. Box 110
6900 AC Zevenaar, The Netherlands
Tel [phone] • Telex 45642
FAX [phone]
#104803327
Tools Requirements: Phillips Screwdriver, Rubber Mallet; cushioned assembly surface
Parts:
Left-hand Door, Right-hand Door, Lock, Keys (lock parts listed below)
(Doors are identified on their interior sides, along with markings indicating which side
faces up)
First install the back Shelf Panels as instructed on the Panel
Assembly Instruction Sheet.
To install the Doors and Lock, first familiarize yourself with all
components. Locate the two matched sets of sockets (top front
edge of Bottom Shelf and lower front edge of Middle Shelf).
Install the Lock on the Right-hand Door before attaching Doors
to Cart.
CC2036DP
Lock:
Lock Parts:
Innermost bag includes:
Lock Parts:
Use the following parts from the outermost bag:
The parts shown below are not needed for lock assembly and can be
discarded:
These parts below will be used for lock assembly along with 4 additional
parts from the outermost bag:
Trim Ring
Keys
Clear Lock
Thread Protector
Offset
Toggle
Lock
Washer
Philip's Head
Screw
Lock
3/4” Nut 90° Stop
Washer
Spur Washer
(for wood)
Straight
Cam
Offset
Cam
180° Stop
Washer
Screw w/
Lock Washer
See reverse side for installation of Lock and
Door Panels.

1d) After inserting both Panels, locate the two
large sockets on the front edge of the underside
of the Middle Panel
2d) Starting with the Right-Hand Door properly orient-
ed (right side as looking at the Cart), insert the large
peg on the top of the Door into the right socket under
the Middle Shelf.
3d) Applying firm
steady pressure, slide
the Door towards the
corner of the Cart until
the peg at the bottom
snaps into the right
socket located on the
top front edge of the
Bottom Shelf. You may
use the Rubber Mallet
to help slightly loosen the Middle Shelf on the edge immediately
above the Door if the fit is too tight. Remember to knock the shelf
back in place if you do this. When properly installed, the Door
should swing freely when opening or closing. 4d) Repeat steps #2 and #3
with the Left-Hand Door
2d
4d
Door Assembly:
Lock Assembly:
1d
3d
Lock Door
Panel
Position Lock with notch side down
3/4” Nut
Clear Lock
Thread Protector
90° Stop
Washer
Offset
Toggle
Lock
Washer
Philip's
Head Screw
1
1) Insert the Lock through the opening in the door as shown with the notch on the bottom side, as indicated. Secure the
Lock with the 3/4” Nut , slide the Clear Lock Thread Protector over the threaded end of the Lock, making sure to push it on
completely so that it is flush with the 3/4” Nut as much as possible. Orient the 90°Stop Washer as shown and slide it on
the square portion at the end of the Lock. Orient the Offset Toggle, also as shown, and slide it over the square portion at the
end of the Lock. Secure these with the Lock Washer and Philip's Head Screw using a Philip's head screwdriver. . Using one
of the keys, the assembled lock should function as shown in the graphic below.
Door – Locked Position
Door – Unlocked Position