Carlton SU 1000 User manual

safety first specifications
Never immerse your facial sauna in water. Never
switch on your facial sauna without first filling the
reservoir with water. Switch off your facial sauna
when all the water has evaporated.
Never place your facial sauna on or near a
source of heat such as a cooker ring or gas flame.
Always keep the facial sauna out of the reach of
small children and never allow the mains lead to
hang over the edge of a work surface. Children
should be taught the dangers of boiling water and
should only ever use appliances while under close
supervision.
Do not interfere with the normal working of the
switch.
Disconnected from the mains when not in use.
Disconnect from power supply after use and
before cleaning.
Do not use if cable or plug is damaged.
Clean the appliance after use to avoid
accumulation of grease or other
residues.
Do not operate your facial sauna with a damaged
cord or plug or if the facial sauna is malfunctioning,
has been dropped or is damaged in any way.
Mains supply: 230-240V ~ 50Hz
Power consumption: 85W
Because we continually strive to improve our products we may change
specifications and designs without prior notice.
If the power cord becomes damaged, it must be
replaced by your service agent or a qualified person
to prevent a hazard. Please contact the store where
you bought your facial sauna.
Always place your facial sauna on a firm and level
surface.
The wires in your facial sauna mains lead are coloured in accordance with the
following:-
The wire which is
coloured Blue must be
connected to the terminal
in the plug which is
marked with the letter N
or coloured Black.
The wire which is
coloured Brown must be
connected to the
terminal in the plug
which is marked with the letter L or coloured Red.
The wire which is coloured Green and Yellow must be connected to the terminal in
the plug which is marked with the letter E or by the Earth symbol or coloured
Green or Green and Yellow.
You must use a 13 amp plug(BS 1363), and fit a 13 amp fuse(BS 1362). If any
other type of plug is used a 13 amp fuse must be fitted, either in the plug, adaptor
or at the distribution board.
wiring instructions
Warning. This facial sauna must be earthed.
facial
sauna
SU 1000
Neutral (N)
Mains lead
Live (L)
Fuse (3 AMP)
Wire clamp
3 AMP
Earth ( )
SU1000.qxd 12/09/2000 16:33 Page 1

troubleshootingusing your facial sauna
cleaning
Cleaning your facial sauna
The facial sauna exterior should be cleaned with a soft damp
cloth. Do not use abrasive cleaners or scouring pads which may
damage the finish of the facial sauna. Never immerse the facial
sauna in water and always keep the power cord dry.
De-scaling your facial sauna
After some time, limescale (calcium carbonate) may be deposited
in the steam reservoir of the facial sauna. This normal build-up is
not harmful but an excessive amount of scale may affect the
operation of the facial sauna. If this happens use a descaling
solution, following the manufacturers instructions. Never attempt
to descale the facial sauna by chipping or scraping with a sharp
implement.
If you live in a hard water area you may need to de-scale the
facial sauna more often.
Pull the cable from
the cable tidy at the
base of your facial
sauna. Plug into a
standard wall
socket.
If the facial sauna doesn't work
please check that:
– Mains power is switched on and the power switch is in the
ON position (the light on the switch should be on).
– Your facial sauna is plugged into the mains supply properly.
Try replacing the fuse in the plug.
If your facial sauna still doesn't work, please contact the store
where it was purchased from.
Place your facial sauna on a level surface. Decide
how long you want your sauna to last (20, 15,
10 or 5 minutes) and fill the measuring cup to
the corresponding level.
Fill the steam reservoir with water
from the measuring cup.
Snap the steam reservoir
cover into the bottom of the
face mask. Place the face
mask on the base with its
opening facing
upwards.
1. Keeping the cord tidy 2. Filling your facial sauna
Press
the power switch
to the ON
position. A short
while after
switching on the
facial sauna,
steam will start to
rise out of the face
mask. You can now
rest your face over the
mask.
After use,
switch off the
facial sauna
and pull out
the plug. After
discarding any
remaining
water, allow the
unit to cool. The
face mask can then
be placed upside
down on the base for
compact storage.
3. Switching on 4. Switching off
Caution. The steam reservoir gets very hot, so do not
touch it during or immediately after use. After use, you may like to rinse your face with cold water
and apply face cream. We recommended that you avoid
cold air and drafts immediately after the sauna.
Caution. Ensure that there is water in your facial
sauna’s steam reservoir before switching on.
Caution. If your facial sauna is overfilled, boiling water
may overflow from the facial sauna. Please note the
reservoir should only hold 25ml of water.
SU1000.qxd 12/09/2000 16:33 Page 2