Casa Lusso FCAB-600 User manual

www.casalusso.com.au
FAILURE TO COMPLY WITH ANY OF THE ABOVE INSTRUCTIONS WILL VOID ALL WARRANTIES
Drawer Front Installation Instructions
FEATURES
GENERAL INFORMATION
The warranty will not apply if:
• The product has been damaged by improper use;
• The product has not been used in accordance with any applicable instruction guide;
• The purchaser has attempted to modify or repair the product;
• The purchaser has failed to observe the cleaning and maintenance guidelines;
Important:
• Take Care While Transporting and Handling Goods.
• This product should be installed by a qualied, licensed Tradesperson.
To tradesperson: Please ensure a copy of the installation instructions
is left with the end user for future reference.
The warranty will not apply if:
• The product has been damaged by improper use;
• The product has not been used in accordance with any applicable instruction guide;
• The purchaser has attempted to modify or repair the product;
• The purchaser has failed to observe the cleaning and maintenance guidelines;
Important:
• Take Care While Transporting and Handling Goods.
• This product should be installed by a qualied, licensed Tradesperson.
To tradesperson: Please ensure a copy of the installation instructions
is left with the end user for future reference.
Material: Moisture resistant 2 pac matte white
Installation:Floor Mount
Includes: 2 x drawer front only.
Premium Warranty (Domestic Use) :
5 year replacement product and parts:
1 year labour
Ensure drawer front/s are inspected fully prior to installation. If damage has occured, or a visable defect exists, do not proceed with installation
and advise supplier immediately. Warranty will be void if product is installed.
Ensure drawer front/s are inspected fully prior to installation. If damage has occured, or a visable defect exists, do not proceed with installation
and advise supplier immediately. Warranty will be void if product is installed.
PRIOR TO INSTALLATION
For FCAB-600, FCAB-750 and FCAB-900 Floor Mount Vanities
Congratulations on the purchase of your new Casa Lusso Vanity. We hope you and your family enjoy your new product
and consider us for any future projects. Casa Lusso products have been manufactured under the highest standards of
quality and workmanship.
5 YEAR
WARRANTY

www.casalusso.com.au
FAILURE TO COMPLY WITH ANY OF THE ABOVE INSTRUCTIONS WILL VOID ALL WARRANTIES
Drawer Front Installation Instructions
For FCAB-600, FCAB-750 and FCAB-900 Floor Mount Vanities
PRODUCT CONTENTS
2 x Drawer Fronts
4 x Fixing
Brackets 8 x Screws 4 x Support Rails
INSTRUCTIONS
Using a Phillips Head screwdriver, screw both fixing brackets into the 2 smaller holes using the screws provided.
Screw in Cam Screw into the hole between the two fixing brackets.
2 x Cam Screws
Using a mallet, hammer both Support Rails into the larger holes.
2 x Cam Locks
1x Cabinet
Drawer Fixing Parts supplied with Casa Lusso Cabinets FCAB-600, FCAB-750 or FCAB-900

www.casalusso.com.au
FAILURE TO COMPLY WITH ANY OF THE ABOVE INSTRUCTIONS WILL VOID ALL WARRANTIES
Drawer Front Installation Instructions
For FCAB-600, FCAB-750 and FCAB-900 Floor Mount Vanities
For the Drawer, inset the Cam Lock underneath as pictured below, turning clockwise until locked in place.
Push Drawer front into cabinet drawer
Drawer front on example
Important - Using a Philips Head Screwdriver, ensure bolt is unlocked (as pictured) before placing drawer front onto
runners. When drawer front is installed, this should automatcially click into ‘Locked position’.
Locked
position
Unlocked
position
Push in
place

www.casalusso.com.au
FAILURE TO COMPLY WITH ANY OF THE ABOVE INSTRUCTIONS WILL VOID ALL WARRANTIES
Drawer Front Installation Instructions
For FCAB-600, FCAB-750 and FCAB-900 Floor Mount Vanities
Allows you to remove the drawer from the drawer runners. Removing the entire drawer from the
runners may assist with installing the drawer front if required. To remove, pull lever up with fingers and
pull drawer towards you. The drawer should come off the drawer runners easily.
Allows you to adjust the
drawer Up and Down.
Use a Phillips Head
screwdriver to adjust.
If drawer is sitting out of
place, this screw allows
you to align it back into
correct position.
Push Support Post into
place. Turn post to adjust
correct length.
Shift cover cap over as
pictured and push until it
‘clicks’.
Post should look as
described as pictured.
Support Post ‘Clicks’
in place here
To remove, push lever and
Support Post should come
away.
Push in
Inserting Support Posts
Adjusting fixings to secure drawer front
Pictured:
Currently in
‘Unlocked
position. Once
drawer is
inserted in
place, this
should
automatically
lock into
position. See
Page 3 for more
info.