Casablanca Tribeca Instruction manual

TribecaTribecaTribeca
English
Owner’s Guide and Installation Manual
Form# M6000-01
20140822
©2014 Casablanca Fan Co.

2
M6000-01 • 08/22/14 • Casablanca Fan Company
Welcome
© 2014 Casablanca Fan Company
Table Of Contents
Preparing the Fan Site .................3
1 • Getting Ready......................6
2 • Installing the Ceiling Bracket........7
3 • Assembling and Hanging the Fan ...8
4 • Wiring Your Ceiling Fan.............9
5 • Installing the Canopy ...............10
6 • Assembling the Blades..............11
7 • Installing the Switch Housing .......12
8 • Installing the Wall Control ..........13
9 • Pairing the Remote .................14
10 • Safe-Exit ..........................14
11 • Operating Your Ceiling Fan ........15
12 • Troubleshooting ..................16
Your new Casablanca® ceiling fan is an addition to your home or
office that will provide comfort and performance for many years. is
installation and operation manual gives you complete instructions for
installing and operating your fan.
We are proud of our work. We appreciate the opportunity to supply
you with the best ceiling fan available anywhere in the world.
Before installing your fan, for your records and warranty assistance,
record information from the carton and Casablanca nameplate label
(located on the top of the fan motor housing).
Cautions and Warnings
•READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING
INSTALLATION. SAVE THESE INSTRUCTIONS.
• Use only Casablanca replacement parts.
• To reduce the risk of personal injury, attach the fan directly to the
support structure of the building according to these instructions,
and use only the hardware supplied.
• To avoid possible electrical shock, before installing your fan,
disconnect the power by turning off the circuit breakers to the
outlet box and associated wall switch location. If you cannot lock
the circuit breakers in the off position, securely fasten a prominent
warning device, such as a tag, to the service panel.
• All wiring must be in accordance with national and local electrical
codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a
qualified electrician.
• To reduce the risk of personal injury, do not bend the blade
attachment system when installing, balancing, or cleaning the fan.
Never insert foreign objects between rotating fan blades.
• To reduce the risk of fire, electrical shock, or motor damage, do not
use a solid-state speed control with this fan. Use only Casablanca
speed controls.
• is product conforms to UL STD 507 and is certified to STD C22.2
No. 113.
• Wash your hands after your fan installation is complete.

3
M6000-01 • 08/22/14 • Casablanca Fan Company
7’ Minimum
Blades to
Floor
9’ Minimum
Ceiling
Height
30” From
Wall or
Nearest
Obstruction
Step 1 - Choose the Fan Site
Proper ceiling fan location and attachment to the building
structure are essential for safety, reliable operation, maximum
efficiency, and energy savings.
Choose a fan site where:
• No object can come in contact with the rotating fan blades
during normal operation.
• e fan blades are at least 7 feet above the floor and the ceiling
is at least 9 feet high.
• e fan blades have no obstructions to airflow, such as walls or
posts, within 30 inches of the fan blade tips.
• e fan is directly below a joist or support brace that will hold
the outlet box and the full weight of the fan.
Checklist for Existing Fan Site
If you want to use an existing fan site, complete the following checklist to
determine if the site is acceptable and safe for your new Casablanca fan.
If you cannot check off every item, prepare a new fan site as described on
this page.
Fan Support System
• Fan attaches directly to building structure.
• Fan support system will hold full weight of the fan and light kit.
Ceiling Hole
• e outlet box clearance hole is directly below the joist or support brace.
Outlet Box
• e outlet box is an UL-approved octagonal 4” x 1-1/2” outlet box (or as
specified by the support brace manufacturer).
• e outlet box is secured to the joist or support brace by wood screws
and washers through the inner holes of outlet box.
• e outer holes of the outlet box are aligned with joist or support brace.
• e bottom of the outlet box is recessed a minimum of 1/16” into
ceiling.
Wiring
• e electrical cable is secured to outlet box by an approved connector.
• Six inches of lead wires extend from outlet box.
If your existing fan site is suitable, skip ahead to Section 2 • Installing the
Ceiling Plate.
Suitable Existing Fan Site
Fan Support
System
Fan Support
System Wiring
Outlet Box
Preparing the Fan Site

4
M6000-01 • 08/22/14 • Casablanca Fan Company
Preparing the Fan Site (continued)
Steps 2 – 3
Step 4
Step 5
CAUTION: All wiring must be in
accordance with national and local
electrical codes and ANSI/NFPA 70. If
you are unfamiliar with wiring, use a
qualified electrician.
Step 2 - Cut the Ceiling Hole
2-1. Locate the site for the ceiling hole directly below the joist or support brace that
will hold the outlet box and fan.
2-2. Cut a 4” diameter hole through the drywall or plaster of the ceiling. You will use
the hole to install the support brace and outlet box.
Step 3 - Install a Support Brace, If Necessary
Determine if there is a ceiling joist directly above the ceiling hole. If the joist is there,
determine if it is positioned to allow you to recess the outlet box a minimum of
1/16” into the ceiling. If NOT, install a support brace as follows:
3-1. Attach a 2” x 4” support brace between two joists. Position it to allow you to
recess the bottom of the outlet box a minimum of 1/16” into the ceiling.
3-2. Check the support brace to ensure it will support the full weight of the fan and
light kit.
Step 4 - Install the Outlet Box
4-1. Obtain a UL-approved octagonal 4” x 1-1/2” outlet box, plus two #8 x 1-1/2”
wood screws and washers, available from any hardware store or electrical supply
house.
4-2. Orient the outlet box so that both the inner and outer holes in the box align
with the joist or support brace.
4-3. Drill pilot holes no larger than the minor diameter of the wood screws (5/64”)
through the inner holes of the outlet box.
4-4. Attach the outlet box directly to the support brace or joist with two #8 x 1-1/2”
wood screws and washers.  e bottom of the outlet box must be recessed a
minimum of 1/16” into the ceiling.
Step 5 - Prepare the Wiring
5-1. Make sure the circuit breakers to the fan supply line leads and associated wall
switch location are turned off . If you cannot lock the circuit breakers in the
off position, securely fasten a prominent warning device, such as a tag, to the
service panel.
5-2. read the fan supply line through the outlet box so that the fan supply line
extends at least 6” beyond the box.
5-3. Attach the fan supply line to the outlet box with an approved connector,
available at any hardware store or electrical supply house.
5-4. Make certain the wiring meets all national and local standards and ANSI/NFPA 70.
You have now successfully prepared your ceiling fan site. For instructions to install
your ceiling fan, go to your fan manual and continue with Section 2 • Installing the
Ceiling Bracket.

5
M6000-01 • 08/22/14 • Casablanca Fan Company
Installer’s Choice and Optional Accessories
Standard Mounting hangs from the
ceiling by a downrod (included).
Support Brace
Standard
Mounting
Style
Ceiling
Outlet Box
Support Brace
Ceiling
Outlet Box
Angled
Mounting
Style
8
12
Angled Mounting recommended for a
vaulted or angled ceiling.
For ceilings higher than 9 feet, you can purchase
Casablanca extension downrods. All Casablanca fans
use sturdy 3/4” diameter pipe to assure stability and
wobble-free performance.
CAUTION: To reduce the risk of personal
injury, attach the fan directly to the support
structure of the building according to these
instructions, and use only the hardware supplied.
Understanding Mounting and Installer’s Choice
Casablanca’s 2-position mounting system provides you maximum
installation flexibility and ease. You can install your fan in one
of two ways, depending on ceiling height and your preference:
standard or angled mounting. e steps in this manual include
instructions for both mounting methods.

6
M6000-01 • 08/22/14 • Casablanca Fan Company
To install a ceiling fan, be sure you can do the following:
• Locate the ceiling joist or other suitable support in ceiling.
• Drill holes for and install wood screws.
• Identify and connect electrical wires.
• Lift 40 pounds.
If you need help installing the fan, your Casablanca fan dealer can
direct you to a licensed installer or electrician.
Gathering the Tools
You will need the following tools for installing the fan:
• Electric drill with 9/64” bit
• Standard screwdriver (magnetic tip recommended)
• Phillips-head screwdriver (magnetic tip recommended)
• Wrench or pliers
• Ladder (height dependent upon installation site)
Checking Your Fan Parts
Carefully unpack your fan to avoid damage to the fan parts. Refer
to the included Parts Guide. Check for any shipping damage to the
motor or fan blades. If any parts are missing or damaged, contact your
Casablanca dealer or call Casablanca Technical Support Department at
888-227-2178.
Preparing the Fan Site
Before you begin installing the fan, follow all the instructions in
“Preparing the Fan Site.” Proper ceiling fan location and attachment
to the building structure are essential for safety, reliable operation,
maximum efficiency, and energy savings.
1 • Getting Ready
WARNING! To avoid possible electrical shock, make certain
that electricity is turned off at the circuit breaker or fuse box
before attempting any installation or repair procedure.
Installing Multiple Fans?
If you are installing more than one
fan, keep the fan blades and blade
irons (if applicable) in sets, as they
were shipped.
If you are installing multiple
remote-controlled fans on the
same circuit breaker,
you may need to perform a few
extra steps to prevent interference
or faulty operation of your remote
controls. Go to
www.CasablancaFanCo.com/FAQs
and click “How do I properly install
multiple remote-controlled fans?”
for more information.

7
M6000-01 • 08/22/14 • Casablanca Fan Company
CAUTION: To avoid possible electrical shock, before installing your fan,
disconnect the power by turning off the circuit breakers to the outlet box
and associated wall switch location. If you cannot lock the circuit breakers
in the off position, securely fasten a prominent warning device, such as a
tag, to the service panel.
2-1. Note: e ceiling bracket may be mounted to an existing ceiling-
-fan-rated outlet box. If the outlet box is not ceiling-fan-rated,
Drill two pilot holes into the wood support structure.
e pilot holes should be 9/64” in diameter and through the
outermost holes in the outlet box.
2-2. Your fan comes with four neoprene noise isolators. Position the
isolators between the ceiling bracket and the ceiling by inserting
the raised areas on each isolator into the holes in the ceiling
bracket.
2-3. Align the slotted holes in the ceiling bracket with the pilot holes
you drilled in the wood support structure. Note: e isolators
should be flush against the ceiling.
2-4. Place a flat washer on each of the two 3” wood screws and pass
the screws through the slotted holes in the ceiling bracket into the
pilot holes you drilled.
2-5. Tighten the screws into the 9/64” pilot holes; do not use lubricants
on the screws. Do not over tighten.
Flat Washer
3” Wood
Screw
Steps 2-3 – 2-5
2 • Installing the Ceiling Bracket
Step 2-2
Ceiling
Bracket
Isolator

8
M6000-01 • 08/22/14 • Casablanca Fan Company
WARNING: Fan may fall if not assembled as directed in these
installation instructions.
You can assemble your fan for standard or angled mounting as
shown in steps below.
3-1. Unbundle the wires from the fan.
3-2. Feed the wires from the fan through the downrod.
Note: Make sure all the wires are on the same side of the metal
dowel pin inside the downrod.
3-3. Loosen the square head setscrew on the adapter in order to
install the downrod.
3-4. Insert the downrod into the adapter. Tighten by turning the
downrod assembly at least 4-5 full turns until it stops.
Note: When the downrod assembly is fully installed, 2-3 threads
on the pipe will still be visible; this is normal. Securely
retighten the setscrew with a wrench or pliers.
WARNING: If the setscrew is not tightened securely, the fan
may fall.
3-5. (Optional) - e wires can be cut (shortened), but leave at
least 8” extending from the top of the downrod.
3-6. Raise the fan and place the downrod ball into the ceiling bracket.
Steps 3-1 – 3-4
Step 3-6
Downrod
Downrod
Canopy
Ceiling
Bracket
Setscrew Adapter
3 • Assembling and Hanging the Fan
For angled ceilings, point
opening toward peak

9
M6000-01 • 08/22/14 • Casablanca Fan Company
4 • Wiring Your Ceiling Fan
All wiring must be in accordance with national and local electrical
codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a
qualified electrician.
4-1. Make sure the power is still off at the breaker box.
4-2. To connect the wires, hold the bare metal leads together and place a
wire connector over them, then twist clockwise until tight. For all wire
connections use the wire connector provided.
CAUTION: Be sure no bare wire or wire strands are visible after
making connections.
4-3. Using a large (orange) wire connector, connect the green or bare
wire (grounding) wire from the ceiling to the green with yellow
striped wire from the ceiling bracket and the green with yellow
striped wire from the downrod.
4-4. Using the small (blue) wire connector, connect the wires from the
fan as follows:
• e blue wire from the fan to the blue wire from the receiver
(marked on white tag “LIGHT OUT”)
• e black wire from the fan to the black wire from the receiver
(marked on white tag “FAN OUT”)
• e white wire from the fan to the white wire from the receiver
(marked on white tag “COMMON OUT”)
Note: e red wire from the receiver will not be used. It has a pre-
installed wire terminator.
F
R
O
M
C
E
I
L
I
N
G
B
R
A
C
K
E
T
F
R
O
M
F
A
N
F
R
O
M
C
E
I
L
I
N
G
F
R
O
M
F
A
N
F
R
O
M
R
E
C
E
I
V
E
R
white black
blue
white (common out)
black (fan out)
Step 4-3
Step 4-4
green or bare (grounding)
green with
yellow stripe
green with yellow stripe blue (light out)
Wire
Connector

10
M6000-01 • 08/22/14 • Casablanca Fan Company
5-1. Raise the canopy over the ceiling bracket and
align the two holes of the canopy and the
ceiling bracket.
5-2. Insert and tighten the canopy screws securely.
Step 5-1 Steps 5-2
Canopy Screw
Canopy
Hanger
Bracket
Canopy
Screw
5 • Installing the Canopy
4 • Wiring Your Ceiling Fan (continued)
4-5. Using the large wire connectors, connect the white wire (grounded)
and the black wire (ungrounded) from the ceiling as follows:
• e white (grounded) wire from the ceiling to the white wire from
the receiver (marked on red tag “NEUTRAL IN”)
• e black (ungrounded) wire from the ceiling to the black wire from
the receiver (marked on red tag “LIVE IN”)
4-6. Check each connection to make sure no bare wire or wire strands are
visible. Turn wire connectors upward and push them up into the outlet
box. Be sure to separate the grounded wires from the ungrounded
wires inside the outlet box.
4-7. Position the receiver in the canopy so that the antenna is close to the
edge of the ceiling bracket for clear reception.
F
R
O
M
C
E
I
L
I
N
G
white
black
white (grounded) black (ungrounded)
Step 4-5
F
R
O
M
R
E
C
E
I
V
E
R

11
M6000-01 • 08/22/14 • Casablanca Fan Company
6 • Assembling the Blades
11
Blade Iron Barrel Nut
Decorative
Screw
Step 6-1
6-1. Using the provided Allen wrench, attach each blade to the
blade iron using three barrel nuts and three decorative
screws as shown.
Note: You have the option to install the blade above or
below the blade iron. In either instance, you may place the
decorative screws and barrel nuts facing up or down.
6-2. Remove the two orange shipping rings from motor by lifting
up on the edge of the rings.
6-3. Align the five holes in the blade iron ring and the decorative
ring with the five holes in the bottom of the motor and
partially install the five blade mounting screws.
6-4. Once all five of the screws are partially installed, tighten
them securely.
Blade
Mounting
Screw
Decorative
Ring
Blade Iron
Ring
Step 6-2
Allen Wrench
Steps 6-3 - 6-4
Shipping
Ring
Note: e blades on this fan have been treated
with Dust Armor protection, making the blades
less likely to attract dust and dirt. Use a dry or
slightly damp lint free cloth to clean the blades.
Do not use a furniture polish or any other cleaners
that leave any residue, as they will damage the
protective Dust Armor on the blades.

12
M6000-01 • 08/22/14 • Casablanca Fan Company
7 • Installing the Switch Housing
12
7-1. To attach the upper switch housing, partially install two housing
assembly screws into the switch housing mounting plate.
7-2. Feed the upper plug connector through the center opening of
the housing.
7-3. Align the keyhole slots in the housing with the housing
assembly screws.
7-4. Turn the housing counterclockwise until the housing assembly
screws are firmly situated in the narrow end of the keyhole
slots. Install the remaining screw into the housing. Tighten all
three screws firmly.
CAUTION: Make sure the upper switch housing is securely
attached to the switch housing mounting plate. Failure to properly
attach and tighten all three assembly screws could result in the
switch housing fixture falling.
7-5. To attach the lower switch housing, connect the upper plug
connector from the motor to the lower plug connector in the
lower switch housing.
Note: Both plug connectors are polarized and will only fit
together one way. Make sure the connectors are properly
aligned before connecting them. Incorrect connection could
cause improper operation and damage the product.
7-6. Place the lower switch housing assembly over the upper
switch housing. Align the side screw holes in the upper and
lower switch housings. Attach the lower switch housing to the
upper switch housing with three housing assembly screws.
Note: You can customize your Casablanca fan with a number
of accessory light kits. To install an optional light kit, remove
the logo cap by removing the two screws located on the inside
of the lower switch housing.
7-7. Use the optional switch housing cap to attach light kits
that mount using a center stem attachment. Follow the
instructions included with the light kit for the wiring,
mounting, and assembly.
Steps 7-1 – 7-4
Housing
Assembly
Screw
Housing
Assembly
Screw
Upper
Switch
Housing
Lower
Switch
Housing
Steps 7-5 – 7-6
Step 7-7

M6000-01 • 08/22/14 • Casablanca Fan Company
8 • Installing the Wall Control
WARNING! To avoid possible electrical shock,
make certain that electricity is turned off at the
circuit breaker or fuse box before attempting any
installation or repair procedure.
8-1. Use only the Casablanca wall control.
Note: Wall Control should only be used on Casablanca
5xxxx Series Fans.
8-2. Do not use any additional control with your fan (for
example, dimmer, or fan speed control).
8-3. Tape the provided wall control template with painter’s
tape at the desired installation area.
8-4. Drill holes inside the four corners of the template.
Note: Make sure the wall control template is level
before proceeding to the next step.
8-5. Using a 9/34 drill bit, drill a hole in each screw cut-out
on the wall control template.
8-6. Using a hammer, tap an included drywall anchor into
each hole until the drywall anchor is flush with the
wall.
8-7. Using a drywall punch saw, cut out the interior shape
of the template using one of the four drilled corners
as a starting point.
8-8. Remove the template and the cut-out section of
drywall.
8-9. Insert the wall control into the dry wall cut out.
8-10.Align the screw holes in the wall control with the drywall
anchors.
8-11.Install the cover plate using a Phillips Head screwdriver
to secure the two cover plate screws through the wall
control and into the drywall anchors.
Steps 8-4
Template
Drill Holes
Painter’s
Tape
Template
Steps 8-6
Drywall
Anchors
Screw
Cut-Out
Template
Steps 8-8
Drywall
Steps 8-9
Steps 8-11
Cover Plate
If you are using a outlet box for wall control installation, the wires coming from the wall
control must be grounded using the attached green wire. If not placed in an outlet box,
cap the green wire coming from the wall control with an included wire nut.
13

14
M6000-01 • 08/22/14 • Casablanca Fan Company
Pairing the Remote
Note: The remote must be paired before the fan will operate.
Learning Mode -This feature shall be initiated by cycling the
power to the fan. For 3 minutes after cycling power to the fan,
the pairing operation can be performed using the wall control.
Begin by pressing both the fan power button and the High
for at least 3 seconds.This will send an encoded binary bit
message to a target receiver-controller.The fan will turn at
the lowest speed signifying that the remote pairing process is
complete.
CFL Lighting
1. Press the fan power button off for at least three seconds to
initiate the Safe-Exit Mode.
2. The lights will ash for visual conrmation.
3. The lights will stay on 100% brightness for 30 seconds. After a
total of 30 seconds, the lights will turn off.
9 • Pairing the Remote
Safe-Exit® (for use with optional accessory light kit)
The Safe-Exit Program gives you about thirty seconds of light when you
turn the lights off, enabling you to exit your home before the lights go
out.To enter the Safe-Exit Program:
Incandescent Lighting
1. Press the fan power button off for at least three seconds to
initiate the Safe-Exit Mode.
2. The lights will ash for visual conrmation.
3. The lights will stay on 50% brightness for 20 seconds and then
begin to dim. After a total of 30 seconds, the lights will be
completely off.
10 • Safe-Exit
If you are installing multiple remote-
controlled fans on the same circuit
breaker, you may need to perform a few
extra steps to prevent interference or faulty
operation of your remote controls. Go to
www.CasablancaFanCo.com/FAQs and click
“How do I properly install multiple remote-
controlled fans?” for more information.

15
M6000-01 • 08/22/14 • Casablanca Fan Company
11 • Operating Your Ceiling Fan
Fan Power
Speed Control
There are four individual speed settings for the fan. Each speed is indicated
by the number on the controller and an audible tone for each speed.
To select the desired fan speed:
Press the number on the controller corresponding to the speed desired.
4 is high, 3 medium, 2 low, and 1 ultra-low. Figure 2.
Note: It is normal for the fan to start in the “High” position from “Off”
before changing to the selected speed.
Reversing Airow
The direction of airow can be changed from downward to upward or
from upward to downward. Figure 3.
To reverse the airow:
1. Make sure the fan is on and blades are turning.
2. Press the reverse button.You will hear a series of clicks from the
fan as it speeds up before coming to a stop and changing direction.
Lights (for use with optional accessory light kit)
To turn the lights off and on, press either the up or down arrow.
To adjust the light level, press and hold either the down arrow to dim the
light or the up arrow to return the light to full brightness.
The fan power button controls power to the fan only. Figure 1.
WARNING! Your fan automatically detects what type of bulbs that are installed
each time it is powered up. NOTE: If CFL bulbs are detected, the dimming
function will automatically be disabled. Remember to turn off the lights before
replacing bulbs.
Figure 1
Figure 2
Figure 3
Figure 4
Battery
1. Press on the battery door to eject it, and unscrew the battery holder.
2. Insert the battery with the positive (+) side facing downard.
3. Reinstall battery holder and insert the battery door into the wall control.
Battery
Battery
Door
Battery Holder

16
M6000-01 • 08/22/14 • Casablanca Fan Company
Problem: Nothing happens; fan does not move.
1. Turn power on, replace fuse, or reset breaker.
2. Loosen canopy, check all connections according to the wiring the
fan section.
3. Remove the shipping bumpers.
4. Make sure the wall control is paired. (See Pairing the Wall Control
on page 14.)
Problem: Noisy operation.
1. Tighten the blade assembly screws and blade iron armature screws
until snug.
2. Check to see if the blade is cracked. If so, replace all the blades.
Problem: Excessive wobbling.
1. If your fan wobbles when operating, use the enclosed balancing kit
and instructions to balance the fan.
2. Tighten all blade iron screws.
3. Turn power off, support fan very carefully, and check that the
hanger ball is properly seated.
Problem: If you have multiple remotes or multiple remote-
controlled fans installed on the same circuit breaker and
you are experiencing interference or faulty operation of your
remote controls, please go to www.CasablancaFanCo.com/FAQs
and click “How do I properly install multiple remote-controlled
fans?” for information on how to correct this issue.
If you need parts or service assistance, please
call 1-888-227-2178 or visit us at our website
at http://www.CasablancaFanCo.com.
Casablanca Fan Company
7130 Goodlett Farms Pkwy. #400
Memphis, Tennessee 38016
12 • Troubleshooting
AUTHORIZED SERVICE CENTERS
For the most updated listing of Casablanca Authorized Service Centers,
visit www.CasablancaFanCo.com/servicecenters or call toll free 1-888-227-2178.

M6000-01 • 08/22/14 • Casablanca Fan Company
Casablanca fans have the power to cut your cooling costs up to 40%.
Beat the High Cost of Cooling
e air movement created by a Casablanca ceiling fan lets you set
your thermostat higher and still stay comfortable. Every degree
you raise the thermostat saves up to 7% on energy costs. So, you
can cut back on expensive air conditioning ... and save up to 40%*
on cooling. In winter, your Casablanca fan recirculates warm air
and saves up to 10%* on heating bills.
* On average at low speed settings. Your savings may vary based
on climate, building type and thermostat setting.
Save Energy and Money While Protecting the
Environment
Congratulations! You’re saving energy and money while protecting
the environment by purchasing this ENERGY STAR qualified
Casablanca ceiling fan! With this purchase, you are doing your
part to protect the environment. In 2010, ENERGY STAR qualified
ceiling fans are projected to cut air pollution by more than 500
million pounds!
Your new ceiling fan has earned the ENERGY STAR label
because it meets high energy efficiency specifications set by
the Environmental Protection Agency (EPA). ENERGY STAR
labeled ceiling fans save energy because they have more efficient
fan motors and air delivery due to more aerodynamic blade
configurations. Ceiling fan models bearing the ENERGY STAR label
move air 14 - 20% more efficiently than typical ceiling fan models.
For more information on ENERGY STAR visit www.energystar.gov.
17