Casambi NB. 1 User manual

PRODUCT MANUAL

LED Controller
Single color
Full protection
CV output
Model No: NB. 1
Smart Control
Compact Size
Cable Holder
Full Protection
High Power
4-in-1 Model
Press Key
Wireless Remote
Introduction
Dimension & Terminal
The NB.1 LED controller is designed to drive constant voltage LED products in voltage range of DC6-24V.
It can be controlled by the CASAMBI app, press key button, touch sensing, or RF remote controller. With multiple
control method, user can control multiple controllers along with other CASAMBI products by smart-phone or by
hardware press-key and RF remote. The controller has full protection function to guarantee the safety of applica-
tions. With compact dimension and cable holders, the installation is easy and secure to make the installation more
reliable and durable.

1. Power supply input
Connect to power supply. The controller can accept supply voltage from DC 6V to 24V, the maximum cable gauge
is AWG12 or 2.5mm2. The controller’s output voltage is at same level as the power input voltage, please make
sure the power supply voltage is correct and the power wattage is capable for the load wattage. Please be noted
the power input ‘+’ unit is directly connected to the output terminal’s ‘+’ unit inside the controller.
2. Press key input
Connect to a press key to control the light directly. Please use normally open type switch which only connect two
poles when the key is pressed. To turn on the press key function, user still need to make corresponding setting on
the controller setting page of CASAMBI App.
3.Work status indicator
This indicator shows all working status of the controller. It displays different events as following:
Steady green : Normal working.
Short green blink : Command received.
Red flash : Overload protection.
Yellow flash : Overheat protection.
4. LED output
Connect to LED loads. The LED loads need to be constant voltage driving and with common anode connection.
Please make sure the LED rated voltage is same as the power supply and each channel’s maximum load current is
below the controller’s rated current. The NB.1 model can be configured to different application for single color or
tunable white.
5. Wiring diagram
6. Press key control
The press key function need to be activated from the App setting page before using. The operation is listed
as following:
Single click : Turn on/off.
Hold press : Dimming.
7. RF remote controller (optional)
Besides smart phone, press key and touch sensing control, it’s also possible to control NB.1 by a RF remote
controller. With specific RF remote controller, user can turn on/off the controller and change brightness. User can
enable or disable the RF remote controller from the controller setting page of CASAMBI App. The remote controller
need to be paired to controller before using. Please refer to remote controller’s manual for detailed operation.

8. Protection function
The controller has full protection function against wrong wiring, output short circuit, overload and overheat. It will
stop working and the indicator will flash red at overload or short circuit situation, the indicator will flash yellow at
overheat situation. The controller will try to recover from protection every 10 seconds after protection occurred,
and will automatically recover working when the condition is good.
9. Change model function
The controller can be configured to single color and tunable white function by CASAMBI app. Please select the
‘Change profile’ function for non-paired controller on app to change model function.
Specification
Working voltage DC 6-24V
Rated output current 3A for each channel, total max 12A.
Standby power <0.5W
Wireless connection CASAMBI protocol, 433MHz RF remote Press key
Press key and touch sensing Normally open press switch
Output mode PWM constant voltage, frequency at 500Hz, 1KHz, 2KHz, 4KHz
Working temperature (Ta) -20°C~+55°C
Dimension 87x24x15mm

Umi Smart Wireless
LED Remote Controller
Function
Model: BR02-C
General Purpose
Dimming Control
Indicator
Dim up
Dim down
Turn 0N/0FF lights
Pair to receiver
*Hold press in 10 seconds
once receiver powered on
Operation
Specification
1. Pair the remote to receiver
The remote controller needs to be paired to receiver to work. User can pair up to 5 remote controllers to one receiver and
each single remote controller can be paired to any receiver.
To pair a new remote to the receiver, please operate with following two steps:
• Cut off the power of receiver and power on again after more than 5 seconds.
• Hold press remote and key simultaneously and briefly in 10 seconds after receiver powered on.
After this operation, the remote is paired to the receiver and ready to work.
2. Unpair the remote controller
To unpair the remote from the receiver, please operate with following two steps:
• Cut off the power of receiver and power on again after more than 5 seconds.
• Hold press all 3 keys simultaneously in 10 seconds after receiver powered on.
After this operation, the remote will be unpaired from receiver.
Working voltage........................................................................DC 3V, CR2O32 battery
Wireless protocol...............................................Umi protocol based on SIG BLE Mesh
Frequency band...................................................................................2.4GHz ISM band
Wireless power......................................................................................................« 7dBm
Working temperature...................................................................-20-50 °C(-4-131 °F)

First time Casambi App use
When first taking devices into use they need to first be added to a network. One device can only be part of one network at
a time. When a device is part of a network it is in a ‘paired’ state and cannot be added to any other network unless it is first
‘unpaired’. i.e., removed from the network.
All Casambi devices are normally supplied in an unpaired state. If a brand-new device is already paired, please contact your
supplier or look for advice in the
FAQ section of our website knowledge base (https://support.casambi.com/support/home).
1. Download the app from Apple App Store or Google Play Store and allow notifications if prompted.
2. Switch on your Casambi enabled devices and open the Casambi app.
3. The app will search for all powered Casambi enabled devices within Bluetooth range of your mobile device. These
will then be displayed in a list with the options to Take into use or Add individually to...
• Take into use will prompt you to create a new network (or add to an existing one). The network should be a Classic
or Evolution type. Only Casambi devices with the same firmware type as the network can be added (See Create a
network section of this user guide for more information). Once the network is created all devices will automatically
be added (paired) to it.
• Add individually to... will prompt you to create a new network (or add to an existing one). The network should be a
Classic or Evolution type. Only Casambi devices with the same firmware type as the network can be added (See
Create a network section of this user guide for more information). Once a network is created, each luminaire will
identify (flash) one by one and can be added to the network (see Add devices section of this guide for more infor-
mation). During this process you can also decide to rename and group luminaires if desired.
4. It is recommended that a new network is shared using the Administrator only setting. See Create new network sec-
tion for further details on network creation.
5. When devices have been added to a network you can control and program them from the app.
The app has four tabs: Luminaires, Gallery, Scenes and More. All of these will be covered in this user guide.
All luminaires in the same network can be easily controlled from the Luminaires tab. Other devices appear in the relevant
section of the More tab.
Additional help texts are shown below most configurable options to clarify the purpose of each setting.
There is also an additional Help option in the More tab. A general help button? Can be found in the bottom right of many
screens. This can be disabled in the App settings.
Luminaires that are paired to your network will be displayed in the Luminaires tab. Each will have an icon picture and a name.
Luminaires that are online (i.e., powered) will also show a bar indicating the current brightness level and light colour.
Luminaire or Group icons shown in the Luminaires tab can be rearranged by tapping Edit selecting and holding the icon and
then dragging it to a different position. Release the icon when it is in its new position. Tap on Done when finished.
Luminaires tab

The basic gestures used to control the luminaires are:
• Tap the luminaire icon to turn the luminaire on or off.
• Pan left or right on the luminaire icon to adjust the luminaire light level. The app remembers the set level so,
if you turn the luminaire on, off and on again using the tap gesture, it will return to that level.
• Pan up or down on the luminaire icon to adjust the colour temperature of a tuneable white luminaire.
• Push and hold the luminaire icon to open the main adjustable parameters.
• For colour changing luminaires, you can set the desired colour.
It is possible to save your favourite colours to the palette. Set the colour and then select and hold an empty
palette space to save it. The colour palette cannot be reset but saved colours can be overridden with
new colours.
• If your luminaire supports more than one channel, you can adjust the channels separately.
Basic Gestures
Tip: Use the same gestures on the All luminaires icon to control all your luminaires simultaneously or use the Near-
by luminaires icon to only control those devices within range of your mobile device.
Tab Pan left / right
Version 4-2022 www.casambi.com suppor[email protected]
Pan up / down Push and hold