Casio 3093 User manual

1
Operation Guide 3093/3094
Stopwatch
The Stopwatch Mode lets you measure elapsed time, split
times, and two finishes. The range of the stopwatch is
59 minutes, 59.99 seconds.
•The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
•The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
•Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
•All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing B.
Timekeeping
Use the Timekeeping Mode to view the current time and
date.
•Day of the week is displayed as follows.
SU : Sunday MO : Monday
TU : Tuesday WE : Wednesday
TH : Thursday FR : Friday
SA : Saturday
To toggle between 12-hour and 24-hour timekeeping
In the Timekeeping Mode, press Cto switch between the
12-hour and 24-hour formats.
•With the 12-hour format, the PM indicator (P) appears
for times in the range of noon to 11:59 p.m. and no
indicator appears for times in the range of midnight to
11:59 a.m.
•With the 24-hour format, times are displayed in the
range of 0:00 to 23:59, with 24H indicator.
MA0702-EA
About This Manual
•The operational procedures for Modules 3093 and 3094
are identical. All of the illustrations in this manual show
Module 3093.
•Button operations are indicated using the letters shown
in the illustration.
•Each section of this manual provides you with the
information you need to perform operations in each
mode.
Module 3093
Module 3094
Timekeeping Mode Alarm Mode Stopwatch Mode Time Setting Mode
Press .
General Guide
•Press Bto change from mode to mode.
•After you perform an operation in any mode, pressing Breturns to the Timekeeping
Mode.
Hourly time
signal on indicator
Mode indicator
Alarm time
(Hour : Minutes)
Alarm on indicator
PM indicator
Day of week
Day
Hour : Minutes Seconds
Alarm
When the Daily Alarm is turned on, the alarm sounds for
20 seconds at the preset time each day. When the Hourly
Time Signal is turned on, the watch beeps every hour on
the hour.
•All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing B.
To set the alarm time
1. Hold down Awhile in the Alarm Mode until the hour
digits start to flash on the display. The hour digits flash
because they are selected.
•This operation automatically turns on the alarm.
2. Press Ato change the selection in the following sequence.
Hour
Normal Alarm Mode (No digit flashes)
Minutes
3. Press Cto increase the selected digits. Holding down Cchanges the number at
high speed.
•The format (12-hour and 24-hour) of the alarm time matches the format you select
for normal timekeeping.
•When setting the alarm time using the 12-hour format, take care to set the time
correctly as morning or afternoon (P).
4. After you set the alarm time, press Ato return to the Alarm Mode.
•If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Timekeeping Mode automatically.
To stop the alarm
Press Ato stop the alarm after it starts to sound.
To switch the Daily Alarm and Hourly Time Signal on and off
Press Cwhile in the Alarm Mode to change the status of the Daily Alarm and Hourly
Time Signal in the following sequence.
Hourly Time
Signal only
Daily Alarm
only
Both offBoth on
To test the alarm
Hold down Cwhile in the Alarm Mode to sound the alarm.
Mode indicator
Minutes Seconds
1/100 second
To measure times with the stopwatch
(a) Elapsed time measurement
Start Stop Re-start Stop Clear
Start Split release Stop Clear
Start Split Stop Split release Clear
(b) Split time measurement
(c) Split time and 1st-2nd place times
First runner
finishes.
Display time of
first runner.
Second runner
finishes. Display time of second runner.
Split
(SPL displayed)

2
Operation Guide 3093/3094
3. While the second’s digits are selected (flashing), press Cto reset the seconds to
. If you press Cwhile the second’s count is in the range of 30 to 59, the seconds
are reset to and 1 is added to the minutes. If the second’s count is in the range
of 00 to 29, the minute’s count is unchanged.
4. While any other digits (besides seconds) are selected (flashing), press Cto
increase the number. While the day of the week is selected, pressing Cadvances
to the next day. Holding down Cchanges the current selection at high speed.
5. After you set the time and date, press Bto return to the Timekeeping Mode.
•If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Timekeeping Mode automatically.
Time Setting
Use the Time Setting Mode to set the current time and
date.
To set the time and date
1. Use Bto enter the Time Setting Mode.
•The second’s digits flash because they are selected.
2. Press Ato change the selection in the following
sequence.
Seconds Hour Minutes
Day of
the Week Day Month
PM indicator
Day of week
Day
Hour : Minutes Seconds