Operation Guide 3558
EN-18
xStopwatch mode
Measuring unit: 1/100 second
Measuring capacity: 23 hours, 59 minutes, 59.99 seconds
Measuring modes: Elapsed time, lap time, two finishes
xDual time mode
xAlarm mode
xHourly time signal
Battery:
One lithium battery (Type: CR2016)
Approx. 5 years operation on type CR2016
(lncludes the alarm for 20 seconds and calculation for 1 hour per day)
NOTE: THERE IS NO WAY unit components can be damaged or malfunction, due
to misoperation of buttons. If confusing information appears on the display it
means entry sequence was incorrect. Please read the manual and try again.
Specifications are subject to change without notice.
EN-17
Specifications
Accuracy at normal temperature:
±
30 seconds per month average
Display capacity:
xRegular timekeeping
Hour, minute, second, am/pm, year, month, day and day of the week on its
double display
Time format: 12-hour and 24-hour
Calendar system: Auto-calendar pre-programmed from the year 2000 to 2099
xCalculator mode
8 digits (7 digits for negatives)
Abilities: Four basic calculations, chain & mixed operations, constants for + / – /
× / ÷, power calculation
Decimal point: Full floating with underflow
Overflow check: lndicated by the “E” sign, locking the calculator mode
EN-16
4. A numeral can be entered in the flashing position by pressing the required numeral
key.
5. Press Bto complete setting.
* While setting time and calendar, with every push of , the display is switched
between 12-hour and 24-hour formats.
EN-15
Setting Time And Calendar
1. To set time and calendar, press Bin the regular timekeeping mode.
2. Press the key on a time signal to correct seconds.
3. Press Ato move the flashing in the sequence shown below to select the other
settings.
SECOND HOUR
(ones)
HOUR
(tens)
AM/PM
MONTH
MINUTE
(tens)
YEAR
AAA
MINUTE
(ones)
DAY
A
A
A
AAA
xAM or PM can be entered by pressing the button.*
EN-14
(a) Elapsed time
(Time loss)
Start Stop Re-start Stop Reset
(b) Lap time
Start Lap Lap release Stop Reset
(c) Two finishes
Start Lap
The first runner
finishes.
Stop
The second runner
finishes.
Record the time of
the first runner.
Lap release
Record the time of
the second runner.
Reset
EN-13
Stopwatch Operation
A signal confirms start/stop operation. The tone sounds at
10-minute intervals.
(Working range) The stopwatch display is limited to
23hours 59 minutes 59.99 seconds.
Thereafter it can be reset and started again. The hour
digits can be shown by pressing the button.
Hour
Lap indicator
Minute
Second
1/100 second
EN-12
Setting Dual Time
1. Press Bto set new time in dual time mode.
2. Press to set PM or AM.*
3. A numeral can be entered in the flashing position by pressing the required numeral
key. The flashing digit can be shifted in the following order:
HOUR
(tens)
MINUTE
(ones)
MINUTE
(tens)
HOUR
(ones)
4. Press Bto complete setting.
* When the watch is in the 24-hour system, the dual time is displayed in that system.
EN-11
[Presetting alarm time]
1. Press Bto set new alarm time.
2. Press to set PM or AM.*
3. A numeral can be entered in the flashing position by pressing the required numeral
key. The flashing digit can be shifted in the following order:
HOUR
(tens)
MINUTE
(ones)
MINUTE
(tens)
HOUR
(ones)
4. Press Bto complete setting.
* When the watch is in the 24-hour system, the alarm time is displayed in that system.
EN-10
Setting Daily Alarm Time
Every time the button is pressed in the
alarm mode, the alarm-ON-mark ( ) appears
or disappears. When the alarm-ON-mark is lit, the
buzzer sounds for 20 seconds at the preset time
every day until cleared. To stop the buzzer while
sounding, press any button.
(Setting the time signal) Every time the button is
pressed in the alarm mode, the time-signal-ON-mark
( ) appears or disappears. When the time-signal-
ON-mark is lit, the watch sounds every hour on the
hour.
(Sound demonstration) While both and
buttons are pressed simultaneously, the buzzer
sounds.
Alarm-ON-mark
A.M.
Hour Minute
Time-signal-ON-mark
