Cavius 9001-003 User manual

Commercial reference: 9001-003
Developed by CAVIUS
PLEASE READ THE USER GUIDE
CAREFULLY BEFORE USE AND
RETAIN FOR FUTURE USE!
General description:
The Smart Remote is designed to alert with a rapid
ashing warning light when alarming and to remotely
control the CAVIUS Wireless Alarm Family. The torch
function can be used to nd escape routes at night.
Technical information:
The Smart Remote can be used with the alarms from
the CAVIUS Wireless Alarm Family: Smoke, Heat,
Flood, CO and Mains Power alarms. The maximum
number of alarms that can be interlinked with is 32.
The minimum range is 100m in open eld. RF conditions
also depend on the house layout and materials. You should
always test it after installation and after changing bat-
teries.
Diameter: 27mm Length: 140mm
The Smart Remote is powered by 3 replaceable DURA-
CELL AAA Alkaline batteries. Please note that correct
operation of the Smart Remote device is ensured by use
of DURACELL batteries.
Interlinked by RF: 868 MHz.
Complies to standards: RoHS, REACH, R&TTE,
EN60065, EN300-220.
How to connect to the Wireless Alarm Family:
1. Open the battery compartment by pressing the snap.
Insert the batteries in the battery compartment respecting
polarities.
2. Slide the learn switch to the “Learn mode” position.
The Smart Remote will go into Learn mode.
All alarms that need to be connected to the Smart
Remote in the house should be put into “Learn mode”
by sliding the switch of each device on the “Learn mode”
position.
3. The ashlight will light up to indicate that “Learn
mode” has been selected.
Please note: Do not take out the batteries during “Learn
mode” as this will interrupt the learn process.
4. Press and hold the test button of the Smart Remote
only, until it beeps and the flashlight flashes. It will
become the master and will start sending out a specic
house code to the other alarms.
5. As the other alarms receive the specic house code,
they will also start ashing their red LED’s.
6. When all alarms ash the red LED, they are connected
and can be switched out of “Learn mode” and installed.
Installation:
The body of the Smart Remote has a built-in magnet, so it
can be installed on a metal plate mounted on the wall,
or on a fridge or other metal surfaces.
The accompanying metal plate can be installed by the
double sided tape or the enclosed screw set.
The end cap has a hole in which a lanyard can be added
so the remote can hang from a hook etc.
Test of alarms:
After installation, and at least once per quarter, test all
your alarms by pressing the test button on the remote to
ensure they are operating correctly and are within range
of each other.
It is recommended to check visually every week if the
LED ashes correctly on the alarm (every 48sec.).
The Smart Remote can activate the RF test function of
the alarms by sending out the a test signal by press-
ing the button at the end for two sound sweeps of
alarm signal 1 (--- --- ---) for about 7 sec. The Smart
Remote will ash/beep every 8 seconds for 120 seconds
to indicate that the test signal is being transmitted.
If the Smart Remote is receiving a test signal from
another device, it will ash/beep every 8 seconds for
120 seconds to indicate that it is part of the group.
Indication can be stopped by pressing the end button.
Please note: To ensure an optimal operation in normal
conditions, test function sends out a reduced power RF
signal.
Alarm mode:
When one of the connected alarms is going into alarm
and sending out the RF alarm signal, the Smart Remote’s
ashlight will start ashing rapidly (stroboscope).
The Smart Remote also has a built in vibrator which will
follow the sound pattern of the sounder. During alarm the
vibrator will vibrate.
The torch can be switched from stroboscopic ashing to
constant on by pressing the side button.
Please note: Flashlight will ash at 2 Hertz (2 times
each second) to avoid photo sensitive epilepsy to
be triggered.
The CAVIUS Wireless Family has two different alarm
signals:
Alarm signal 1 (--- --- ---) is life threatening alarms, like
a smoke alarm.
Alarm signal 2 (- - -) is a non life threatening alarm, like
a ooding alarm:
Smoke alarm signal: --- --- ---
Heat alarm signal: --- --- ---
Flood alarm signal: - - -
CO alarm low level signal: - - -
CO alarm high level signal: --- --- ---
Please note that only the originating alarm’s LED will
ash, so it can be identied.
Alarm silence:
When the alarms from the Wireless Alarm Family go
into alarm, they can be silenced by pressing end button
of the Smart Remote.
Please note: Due to coming legislation, the hush signal
is transmitted with reduced power (the remote must
be within short range from the silenced alarm, which
means you should be in the same room as the alarm).
UK
Flashlight
End cap for battery access
End button for test/hush
Magnet holder
Learn mode switch
Side button for ashlight
Normal Mode Learn Mode

Developed by CAVIUS Aps Julsøvej 16, DK-8600
Manufactured in P.R.C.
126894 rev2
The CE mark afxed to this product conrms its compliance
with the European Directives which apply to the product.
All Rights reserved: CAVIUS Aps assumes no responsibility
for any errors, which may appear in this manual. Further-
more, CAVIUS Aps reserves the right to alter the hardware,
software, and/or specications detailed herein at any time
without notice, and CAVIUS Aps does not make any com-
mitment to update the information contained herein. All the
trademarks listed herein are owned by their respective owners.
Copyright © CAVIUS Aps.
You can silence any of your alarms in the system, as long
as you are in in the same room and within short range
of the alarm.
When you silence the source of the alarm, the alarm that
originally went into alarm with ashing red LED, all the
other devices will be silenced too.
If you silence an alarm other than the source of the
alarm, the remaining alarms will still sound.
The Smart Remote can only stop the alarmed device
after 30 seconds in alarm stage. This will be indicated
by a short ash. The reason for that is to make sure you
have identied the source of the re before using the
hush function.
Please note: the Smart Remote can’t receive while
sending.
Flashlight:
The ashlight can be activated by pressing the side but-
ton. By pressing again you turn off the light.
Please note: The light will go out automatically after 5
minutes.
Low battery signal:
When the battery is starting its end of life, a short beep
will sound out every 48 seconds for 30 days.
Only the device affected by the low battery will beep, no
other connected devices will sound.
It is safe to change batteries in the Smart Remote
without going through the learn process again – it will
not forget the codes during the battery change process.
Batteries replacement:
You can access the 3 x AAA batteries by removing the
end cap.
Replace the batteries respecting polarities. Always test the
Smart Remote after battery replacement.
Caution: There is a risk of explosion if the batteries are
replaced by an incorrect type.
Dispose of used batteries according to local environmental
regulations.
Maintenance & troubleshooting:
If the Smart Remote does not work when the test/Hush
button is pushed, the probable cause is faulty batteries
which must be replaced. Please refer to troubleshooting
at www.cavius.com.
HEAT ALARM
SMART REMOTE
FLOOD ALARM
SMOKE ALARM
MAINS POWERED
SMOKE ALARM