CDN VIKIKI OFFICE DESK 3054 User manual

MODEL:
ASSEMBLY INSTRUCTION
VIKIKI OFFICE DESK
3054
1)
DO NOT
FULLY
TIGHTEN
THE
NUT
OR BOLT
UNTIL THE
PRODUCT IS
ASSEMBLED.
(TO
AVOID
CAUSING
DAMAGE
TO THE
THREAD
DO NOT OVER
TIGHTEN
THE
NUT
OR
BOLTS)
2)
KEEP
ALL
HARDWARE
PARTS OUT
OF
REACH
OF
CHILDREN
HARDWARE LIST
PART LIST
O
IV
V VI
VIl VIll X X
XI
T
CoDE QTY
E
Wood Miniflx Minifix Drawer Slide 3.6x12mm| Leg Iron L|3.5xi 8mmLegLeg Cover JCBC
610mm60OmmPin MBx5Omnm
pVC ICBC
Nail Bracket | Screw
Screw
24 2 1
Pcs Pcs Pc
XVI XV XVIM
XIX
9
14
L
(M)
Dowel Com Pn
25
Sets
XIV
A 32 2 2 4 4
10
Pcs
XII IT
3
Sets
XV
Pca Pcs Pcs Pcs Pcs
XX
H)
2
Allen
Allen|
Key
M4Washer |
M6x45mm|
M5x40mm
M3
Cap
Screw
Lock
Minifix
1815
6
Pcs Pos Po Pcs Pos Set
M6 Screw
Scre
Key Hole 4x38mm Loc
D 1
Cap
12
14
Pc Pcs
14
Pcs
E
F
1 B
G
H
MINIFIX SETUP
1
(D
TEP
(>) UNLoCK
3 E
K
83 STEP 2
STEP3
LOCKED
3 O
M
M3
N 3
O 3
(?)
COMPLETE
M
P Page I
of 7

3 SET
STEP 2
1 PCS
25 25 PCS
24 PCs
STEP
IV
Attach 3x slide rails (l) in place on
each of the paneis [A] [D] using 4x
12mm small screws (IV) in each rail
C
bracket. Fasten all screws.
D
(
A
IV
J
D)
IMPORTANT NOTE:
PLEASE CHOOSE THE
CORRECT SCREW HOLE
P)
BEFORE FITTING THE
DRAWER RUNNER.
Insert 10x dowel (I) and 25x pin (|l-pin) into all panel as shown.
O
Page 2 of 7

2 STEP 4
1 PC
VI 2 PCS
VII
2PCS PCS
STEP
V
VI S
IX
2 PCS
4 PCS
4 PCS
XLL
1 PC
4 PCS
Attach 4x cover pin (X) into metal
(VIll)x2
as shown
with
a
hammer.
Attach leg nail (V) into
panel
[F]
as
shown
with
a hammer.
VI
L
VI
V
tttttttttI
I Join
metal (VIlI)x2 (1X)x2 by using
4x washer (XIIl) and 4x screw (XI)
and tighten with allen key (XI).
XI
Attach 1x bracket (VI) in panel [)
using 2x screw (VIl).
Page 3 of 7

STEP 5
D4 PCS
1 PC
XIV
XIV
XIT
tmmn
6 PCS
STEP
6 KII
1 PC
4 PCS
Place 4x locking nuts (ll nut)
into holes in connecting parts
and tighten with screwdriver.
C
B
XIV
www
XII
Join panel [B] to panel [A] [D]
by screw in 6x screws (XIV)
into corresponding holes and
tighten with allen key (XII).
Join panel [E] to panel [A] [D]
by screw in 4x screws (XIV)
into corresponding holes and
tighten with allen key (XII).
Page 4 of7

STEP 7 8
PCS
STEP 8
XIV
XII
4, PCS
1 PC
XIV
ttrrr-
w
XI
G)
VI
Join panel [G] to panel [A] [F1
by screw in 4x screws (XIV)
into corresponding holes and
tighten with allen key (XIl).
Attach assemble metal to base of panel [E] by using
8x screw (VII). Fasten all screws.
Pago 5 of 7