CEBEK I-208 User manual
ELECTRONIC CIRCUITS
DIGITAL TIMER - CONTROLLER TILL 1 MONTH.
TIMERS I-208I-208
I-208I-208
The I-208 module is a timer to control voltage a device. Specially recommended for renting apparatus, houses,
games, etc...
It includes a led to indicate its state as well as connection terminals to make more easy its assembly.
OPERATING.
TECHNICAL CHARACTERISTICS.
Voltage. .............................................................................................12 V. DC.
Minimum Consumption. ...................................................................12.6 mA.
Maximum Consumption. ..................................................................47.3 mA.
Operating timing. ..............................................................................1, 2, 3 or 4 Weeks.
Maximum Output intensity. .............................................................. 3 A.
Protection against polarity inversion .................................................. Yes.
Ref. Full9907
POWER SUPPLY. The
MODULE’S USING. The I-208 is a timer with a long cycle to control the use of devices.Specillay indicated for
renting apparatus, electronic devices, renting houses, games, etc.... The circuit will maintain the operating
during the selected time and it stops the device when the time is finished. Then, the owner’s “conformity“ will be
necessary to activate again the apparatus. Indeed, when the module is activated it allows the controlled
device to be supplied during one of the four times previously selected. At the end of the selected timing, the I-
208 module will disconnect the voltage and the controlled device could only be activated again for a similar
timing till the I-208 is activated.
This operation only could be done inserting an ”electronic key” supplied with the module. (See corresponding
paragraphe).
HOW TO SELECT OPERATING TIME. The I-208 module allows four different times, composing the module’s
I-208 circuit had to be supplied by a 12 VDC power supply correctly filtered. We recommended
you the FE-2 power supply which has been developed to perfectly answer to the circuit needs. Install a fuse and a
switch has it is indicated on the schedule. Both are necessary for the module’s protection as well as for your own
safety, as it is required by the “CE” regulations. Connect the positive of the power supply to the positive terminal
indicated in the wiring map, then connect the negative of the power supply to the negative terminal indicated in the
circuit. Verify that the assembly is correct.
1
OPERATING.
2
HOW TO CONFIGURATE switches according to OPERATING TIME.
Switches
Switches
How to place switches to select
a timing corresponding to 1 week.
How to place switches to select
a timing corresponding to 3 weeks.
1
ON
21
ON
2
Switches
Switches
How to place switches to select
a timing corresponding to 2 weeks.
How to place switches to select
a timing corresponding to 4 weeks.
1
ON
21
ON
2
operating time. Thanks to the included switches (2 units) you oculd select among 1, 2, 3 or 4 weeks.
Hereafter, you could see how to combine both switches to select a time.
OUTPUT CONNECTION. LOAD OR CONTROLLED APPARATUS. The I-208 output is controlled by a relay, and
accept any device up to 3 A. The relay have three output terminals: The normally open quiescent (NO), the
normally closed quiescent (NC) and the common. This mechanism operate like a switch with two terminals NC
and Common to control the apparatus supplly (allowing or stopping the voltage). For the inverse function you
have to use the NO and Common. In the drawing hereafter, you could see a typical connection with a 12 V
D.C and 230 V A.C devices.
INFORMATION ABOUT THE OUTPUT. During the operating mode and according to its load, it could happen a
fluctuation or an incorrect working of the output. In such case, you have to install an anti-spark circuit between
both contacts of the used relay, as it is indicated on the schedule.
OPERATING. Once output and voltage connections done, you could activate the switch to supply the moule.
The Led will light on or constantly intermittent. To activate the fisrt time the module as well as to reactivate the
module after timing, or to start from the beginning during a timing unfinished, you have to “charge” thanks to
the supplied electronic key. This key have to be correctly safeguarded, because the warranty does not applied
if you lose or bkreak it.
To “charge” the module. To “charge” the module, you have to insert the electronnic key during more than 1
Common
(NO) Normally Open
(NC) Normally Closed
Apparatus,
Load.
100nF/400 V.
47W1/2W.
Load supply
Electronic key
230 V. AC. CONNECTION12 V. DC. CONNECTON
12 V. DC
Common Common
(NO) Normally Open (NO) Normally Open
(NC) Normally Closed (NC) Normally Closed
Load,
Device
Load,
Device
230 V. AC.
ELECTRONIC CIRCUITS
DIGITAL TIMER - CONTROLLER TILL 1 MONTH.
TIMERS I-208I-208
I-208I-208
The I-208 module is a timer to control voltage a device. Specially recommended for renting apparatus, houses,
games, etc...
It includes a led to indicate its state as well as connection terminals to make more easy its assembly.
OPERATING.
TECHNICAL CHARACTERISTICS.
Voltage. .............................................................................................12 V. DC.
Minimum Consumption. ...................................................................12.6 mA.
Maximum Consumption. ..................................................................47.3 mA.
Operating timing. ..............................................................................1, 2, 3 or 4 Weeks.
Maximum Output intensity. .............................................................. 3 A.
Protection against polarity inversion .................................................. Yes.
Ref. Full9907
POWER SUPPLY. The
MODULE’S USING. The I-208 is a timer with a long cycle to control the use of devices.Specillay indicated for
renting apparatus, electronic devices, renting houses, games, etc.... The circuit will maintain the operating
during the selected time and it stops the device when the time is finished. Then, the owner’s “conformity“ will be
necessary to activate again the apparatus. Indeed, when the module is activated it allows the controlled
device to be supplied during one of the four times previously selected. At the end of the selected timing, the I-
208 module will disconnect the voltage and the controlled device could only be activated again for a similar
timing till the I-208 is activated.
This operation only could be done inserting an ”electronic key” supplied with the module. (See corresponding
paragraphe).
HOW TO SELECT OPERATING TIME. The I-208 module allows four different times, composing the module’s
I-208 circuit had to be supplied by a 12 VDC power supply correctly filtered. We recommended
you the FE-2 power supply which has been developed to perfectly answer to the circuit needs. Install a fuse and a
switch has it is indicated on the schedule. Both are necessary for the module’s protection as well as for your own
safety, as it is required by the “CE” regulations. Connect the positive of the power supply to the positive terminal
indicated in the wiring map, then connect the negative of the power supply to the negative terminal indicated in the
circuit. Verify that the assembly is correct.
1
OPERATING.
2
HOW TO CONFIGURATE switches according to OPERATING TIME.
Switches
Switches
How to place switches to select
a timing corresponding to 1 week.
How to place switches to select
a timing corresponding to 3 weeks.
1
ON
21
ON
2
Switches
Switches
How to place switches to select
a timing corresponding to 2 weeks.
How to place switches to select
a timing corresponding to 4 weeks.
1
ON
21
ON
2
operating time. Thanks to the included switches (2 units) you oculd select among 1, 2, 3 or 4 weeks.
Hereafter, you could see how to combine both switches to select a time.
OUTPUT CONNECTION. LOAD OR CONTROLLED APPARATUS. The I-208 output is controlled by a relay, and
accept any device up to 3 A. The relay have three output terminals: The normally open quiescent (NO), the
normally closed quiescent (NC) and the common. This mechanism operate like a switch with two terminals NC
and Common to control the apparatus supplly (allowing or stopping the voltage). For the inverse function you
have to use the NO and Common. In the drawing hereafter, you could see a typical connection with a 12 V
D.C and 230 V A.C devices.
INFORMATION ABOUT THE OUTPUT. During the operating mode and according to its load, it could happen a
fluctuation or an incorrect working of the output. In such case, you have to install an anti-spark circuit between
both contacts of the used relay, as it is indicated on the schedule.
OPERATING. Once output and voltage connections done, you could activate the switch to supply the moule.
The Led will light on or constantly intermittent. To activate the fisrt time the module as well as to reactivate the
module after timing, or to start from the beginning during a timing unfinished, you have to “charge” thanks to
the supplied electronic key. This key have to be correctly safeguarded, because the warranty does not applied
if you lose or bkreak it.
To “charge” the module. To “charge” the module, you have to insert the electronnic key during more than 1
Common
(NO) Normally Open
(NC) Normally Closed
Apparatus,
Load.
100nF/400 V.
47W1/2W.
Load supply
Electronic key
230 V. AC. CONNECTION12 V. DC. CONNECTON
12 V. DC
Common Common
(NO) Normally Open (NO) Normally Open
(NC) Normally Closed (NC) Normally Closed
Load,
Device
Load,
Device
230 V. AC.
TIMERS I-208I-208
Ref. Full9907
GENERAL WIRING MAP.
4
All the module’s CEBEK have 3 years of total warranty in thecnical
repairing, and spares from the date of buy.
CEBEK is trade make of FADISEL S.L. more than 300 module’s are avaible in
stock for any purpose request our CATALOGUE, or visit our Web.
Http://www.cebek.com
TECHNICAL CONSULTATIONS.
If you have any doubt, you could contact your wholesaler or our Technical Department.
- Via E-Mail, sat@cebek.com | by mail P.O Box 23455 - 08080 BARCELONA - SPAIN.
ELECTRONIC CIRCUITS
DIGITAL TIMER - CONTROLLER TILL 1 MONTH.
I-208I-208
OPERATING.
When you insert the key into the key jumper, the status led will completely light on during 2 sec. then, the module
immediately start from the beginning the pre-selected timing. Do not forget that each time you “charge” the
module, it will start form the beginning the timing.
Afterthe timing, the module will disconnect the output and wait you “charge” again it.
How to “Charge” the module.
DO NOT FORGET. The I-208 module doesn’t count the time when it is not supplied, but it store into its memory
the value till it is supplied again.
For this reason, you have to know that to adjust the module for a timing corresponding to 1 week for instance,
the effective time that the module will maintain connected the output will correspond to the sum of partial
times that the apparatus has been connected till a maximum of 1 week.
3
sec. In the piece or jumper indicated as “Key” on the circuit.
1st. Step. Introduce the electronic key on the key jumper.
Electronic Key
“Key” Jumper
Transversal View of the Circuit.
3 rd. Step. Remove the electronic key from the Key Jumper.
Electronic Key
“Key” Jumper
Transversal View of the Circuit.
2nd. Step. Maintain the electronic key on the Key Jumper during 1 sec. as miminum.
Electronic Key
“Key” Jumper
>1 sec.
Transversal View of the Circuit.
NC
Common
Relay Output
NO
RELAY
Led
State
Power
Switches
Module
I-208
Power Supply
00
001515
230230
230 V. AC. Mains
Mains
Swicth
Led
250 mA.
Fuse
Transformer
12 V. DC.
15 V. AC .
Module
FE-2
15
0
1
ON
2
Jumper
Key
Y
S
E
R
A
TIMERS I-208I-208
Ref. Full9907
GENERAL WIRING MAP.
4
All the module’s CEBEK have 3 years of total warranty in thecnical
repairing, and spares from the date of buy.
CEBEK is trade make of FADISEL S.L. more than 300 module’s are avaible in
stock for any purpose request our CATALOGUE, or visit our Web.
Http://www.cebek.com
TECHNICAL CONSULTATIONS.
If you have any doubt, you could contact your wholesaler or our Technical Department.
- Via E-Mail, sat@cebek.com | by mail P.O Box 23455 - 08080 BARCELONA - SPAIN.
ELECTRONIC CIRCUITS
DIGITAL TIMER - CONTROLLER TILL 1 MONTH.
I-208I-208
OPERATING.
When you insert the key into the key jumper, the status led will completely light on during 2 sec. then, the module
immediately start from the beginning the pre-selected timing. Do not forget that each time you “charge” the
module, it will start form the beginning the timing.
Afterthe timing, the module will disconnect the output and wait you “charge” again it.
How to “Charge” the module.
DO NOT FORGET. The I-208 module doesn’t count the time when it is not supplied, but it store into its memory
the value till it is supplied again.
For this reason, you have to know that to adjust the module for a timing corresponding to 1 week for instance,
the effective time that the module will maintain connected the output will correspond to the sum of partial
times that the apparatus has been connected till a maximum of 1 week.
3
sec. In the piece or jumper indicated as “Key” on the circuit.
1st. Step. Introduce the electronic key on the key jumper.
Electronic Key
“Key” Jumper
Transversal View of the Circuit.
3 rd. Step. Remove the electronic key from the Key Jumper.
Electronic Key
“Key” Jumper
Transversal View of the Circuit.
2nd. Step. Maintain the electronic key on the Key Jumper during 1 sec. as miminum.
Electronic Key
“Key” Jumper
>1 sec.
Transversal View of the Circuit.
NC
Common
Relay Output
NO
RELAY
Led
State
Power
Switches
Module
I-208
Power Supply
00
001515
230230
230 V. AC. Mains
Mains
Swicth
Led
250 mA.
Fuse
Transformer
12 V. DC.
15 V. AC .
Module
FE-2
15
0
1
ON
2
Jumper
Key
Y
S
E
R
A
Table of contents
Other CEBEK Controllers manuals
