Cedar Salome User manual

427cm [168.1in]
cm
305 [120in]
mc992 [117.71in]
IMPORTANT, RETA N FOR FUTURE REFERENCE: READ CAREFULLY
For Outdoor Use only. Not for Commercial Use.
Assembly Manual
, ( ft ft)
In case of any malfunction of your COSTCO product (failure, missing part, etc.),
please contact one of our service technicians at our toll-free service line at
1-855-586-8118 from 8:30 AM to 5:30 PM, EST,Monday to Friday.

-1-
SAFETY INFORMATION
PREPARATION
Please read and understand this entire manual before attempting to assemble, operate or install
the product.
WARNING
CAUTION
Before beginning assembly of product, make sure all parts are presented. Compare parts with
package contents list and hardware contents list. If any part is missing or damaged, do not attempt
to assemble the product.
Estimated Assembly Time: 3 hours.
Tools Required for Assembly (not included in the box):
Safety goggles
Screwdriver
Hammer Gloves Stepladder
Hardhat
SET UP YOUR GAZEBO PROPERLY
• This unit is heavy. Do not assemble this item alone. 4 people are recommended for safe assembly.
• Keep all children, pets and other obstructions away from assembly area.
• If any part is missing or damaged, do not attempt to assemble the product.
• In order to avoid damage to the gazebo and its components please use appropriate tools.
• Do not use the structure as support.
• Check all bolts on a regular basis to maintain the solidity of the structure.
• Keep instruction manual for future use.
• Do not climb on top of the gazebo. Falling off the gazebo can result in serious injury,
possibly even death.
EXAMINE YOUR GAZEBO
• Examine occasionally to ensure there are no loose parts.
If loose parts are found, they should be retightened immediately.
• Maximum load for the roof :18,14kg(40 lb).
•WARNING: KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THIS GAZEBO FABRIC.
This item meets the CPAI-84 flammability requirements. The fabric may burn if left in continuous
contact with any flame source. The application of any foreign substance to the tent fabric may
cause the flame-resistant properties ineffective.
• In case high winds, heavy rains or snow occur, remove mosquito net, clear snow from the roof
immediately, and check for damage before continuing use.
Electric drill

A1
A2
A3
Left-Long Lintel
Right-Long Lintel
Left-Short Lintel
Right-Short Lintel
2
2
2
A4 2
B
Connector 4
C1
C2
D
E
Corner cover
Lintel Cover
Connection Piece
Post
Base Plate
Base Cover
Top Cover
Cover
Corner Piece
Long-Top Bar
Short-Top Bar
4
4
8
4
F1
F2
4
4
G
G1
4
4
H4
Components
I1
I2
-2-
8
4

4
4
K1 2
K2 Top Connecting Tube 2
Top Frame
2
L1
Small Top Lintel
Center Cover
Center Connector
Hook
Small Top Support Bar
Small Top Center Bar
Short Bar-Small Top
Left-Long Bar-Small Top
Right-Long Bar-Small Top
Left-Long Bar-Big Top
Right-Long Bar-Big Top
Left-Short Bar-Big Top
Right-Short Bar-Big Top
Top Center Bar-Big Top
Small Top Lintel
2L2
1
1
1
M1
M2
M3
N
N1
O2
O
O1
P1
P3
P4
P2
P5
4
-3-
4
4
8
4
4
2
2
2
2
J1 Left-Support Bar
J2 Right-Support Bar

-4-
Q1
Q2 2
2
R1 2
R2 4
R3 2
R4 2
S1 16
S2 8
T1 4
T2 4
Short Edge Sealing
-Small Top
Long Edge Sealing
-Small Top
L Plate
L Plate
L Plate
L Plate
Short Trim Strip
Small Top Cover
Big Top Cover
Air Vent
Mosquito Netting
Big Top Panel
Long Trim Strip
V1 4
U2 1
2
U
1tf4 -2
1tf4 -2
0
1tf -3
01 tf -3
1tf4 -4
1tf4 -4
01 tf -1
01
U1 Air Vent 2

V4 4
V5 4
V6 2
V7
V8
2
2
V2 Big Top Panel
Big Top Panel
Big Top Panel
Big Top Panel
Big Top Panel
Big Top Panel
Big Top Panel
4
V3 2
-5-

W1 2
W2
W3
2
2
AA Bolt\Flat Washer
(m6*15) 282
Stake
14
16
2
Wrench
8
BB
Allen Wrench
Allen W
Sleeve
rench
2
1
1
CC 60
DD
EE
FF
GG
HH
JJ
KK
LL
MM
NN
OO
Bolt\Flat
Washer\ Nut
(m6*32)
8
Bolt\Flat Washer
(m6*20)
Bolt\Plastic Washer
(m6*35)
Bolt\Flat Washer
(m6*40)
Bolt\Plastic Washer
(m6*40)
2
Screw
8
8
48
Bolt\Flat Washer
(m8*15)
Hardware
Small Top Panel
Small Top Panel
Small Top Panel
Bolt\Flat
Washer\ Nut
(m6*55)
-6-
W4 Small Top Panel 2

Step1
Fig 2 Fig 1
E
G
F2
AA
AA
F1 E
G
Fig 2
AA
E
AA AA
GG
F2 E
Fig 1
E
1. Insert the Base Cover (F2) into the Post (E), then connect the Base Plate (F1) to the Post (E) by
Bolts (AA), as per Fig 1. Connect the post (E) to the Top Cover (G) by Bolts (AA), as per Fig 2.
-7-
AAx20 Ex4 Gx4
F2x4
F1x4
X4 X4

Step2
A3
A4
Fig 3
A1
A2
Fig 3
A1/A3
A1/A3
D
BB B
A2/A4
BB
A2/A4
BB
A3
A4
A2
A1
A1/A3 A2/A4
D
A1/A2
C2
AA
AA
2. Insert the Connector (B) into the Left-Long Lintel/Left-Short Lintel (A1/A3), fix them with the three
bolts but don't tighten them. Insert the Right-Long Lintel/Right-Short Lintel (A2/A4) into the Connector
(B), fix the Connection Piece (D) to the lintel by Bolts (BB), connect the Lintel Cover (C2) to the lintel
by bolts (AA), Connect the Long Lintel (A1/A2) and the Connection Piece (D) by bolts (AA). as per Fig
3.
-8-
Dx8
AAx16 BBX48
A1x2 A3x2
A2x2 A4x2
C2x4
Bx4
X4
X4
X4
X4

Step3
Fig 6
E
E
E
A1
A2 E
A2
A1
Fig 5
Fig 5 Fig 6
A1 A2
GG
AA
E E
3. Connect the Top Cover (G) to the Left-Long Lintel (A1) by Bolts (AA), as per Fig 5. Connect the
Top Cover (G) to the Right-Long Lintel (A2) by Bolts (AA), as per Fig 6.
-9-
AA
AAx16
X2 X2

Fig 7
A1
Fig 8
A2
AA
J1 J2
AA EEAA
AA
4. Fix the Support Bar (J1/J2) on the Post (E) and the Left-Long Lintel/Right-Long Lintel (A1/A2)
by Bolts (AA), as per Fig 7 & Fig 8.
Step4
Fig 8
J2
E
J1
E
E
A1
A2
J2
E
A2
A1
Fig 7
J1
-10-
AAx16 J1x2 J2x2
X2 X2

Step5
Fig 13
A2
A3
A1
J1
A4 A4
E
A3
J1 A1
A2
J2
E
Fig 10/Fig 12
E
J1 E
J2
J2
J1
Fig 9/Fig 11
-11-
Fig 9 Fig 10
A1 A4 A3 A2
AA
AA
EE
X2 X2

Fig 11 Fig 12
A1 A4 A3 A2
J2
AA
EAA
Fig 13
H
CC
AA
AA
J1
AA
EAA E
5. Connect the Post (E) to Left-Short Lintel/Right-Short Lintel (A3/A4) by Bolts (AA), fix the
Support Bar (J1/J2) on the Post (E) and lintel by Bolts (AA). Connect the Corner Piece (H)
to the Top Cover (G) by Bolts (CC). Connect the Cover (G1) to the Top Cover (G) by Bolts (AA).
as per Fig 9-Fig 13.
-12-
G1
AAx40 J1x2 J2x2
x4
xG1x4
X4 X4
X2
X2

Step6
K2
K1 K1
K2
Fig 14
Fig 14
K1
K2
AA
6. Insert the Top Connecting Tube (K2) into the Small Top Frame (K1), then connect them with
the Bolts (AA), as per Fig 14.
-13-
AAx4 K1x2 K2x2
X4

Step7
K1
K2
I1
Fig 16
I1
±5mm
Fig 15
K1 I1
Fig 15 Fig 16
I1
K2
K1
A2
A3
AA
AA
I1
E
7. Connect the Long-Top Bar (I1) to the Corner Piece (H) by Bolts (HH), connect the Long-Top Bar
(I1) to the Small Top Frame (K1) by Bolts (AA), as per Fig 15-Fig 16.
Note: Be sure to have ±5mm of tolerance when installation is complete.
-14-
HH
AAx8
HHx8
I1x4
X4
X4

Step8
Fig 17
K2
K1
A4
I2
I2
A1
Fig 18
A2
I2
S
A3
A4
Fig 17 Fig 18
I2
K2 D
AA A1/A2/A3/A4
AA
I2
AA
I2
D
A1/A2
AA
8. Connect Short-Top Bar (I2) to the Top Connecting Tube (K2) by Bolts (AA), connect the
Connection Piece (D) to the Short-Top Bar (I2) by Bolts (AA), as per Fig 17-Fig 18.
Connect Short-Top Bar (I2) with Small Top Frame (K1) at the adjacent side by Bolts (AA).
-15-
AAx24 I2x8
X8X4 X4

Step9
M2
N
L1
L2
L1
Fig 19
L2
N
DD
L1
L2
L1
N
N
N
M2
N
HH
M2
M3
9. Connect the Small Top Lintel (L1) to the Small Top Lintel (L2) by Bolts (DD),Connect the Small
Top Support Bar (N) to the Center Connector (M2) by Bolts (HH), then insert the Small Top
Support Bar (N) into the Small Top Lintel (L2). connect the Hook (M3) to the Center Connector
(M2), as per Fig 19.
-16-
L1x2 L2x2 M2x1 Nx4
DDx8
HHx4
X4
X4
X1
X4
M3x1

Step10
M2
L1 N1 K2
L2
Fig 20
L1
L1
K1
AA
L2
K2
AA
M2
HH
N1 AA N1
K2
10. Connect the Small Top Lintel (L2) to the Small Top Frame (K1) by Bolts (AA). Connect the Top
Connecting Tube (K2) to the Small Top Lintel (L1) by Bolts (AA), connect the Small Top Center Bar
(N1) to the Top Connecting Tube (K2) by Bolts (AA), connect the Small Top Center Bar (N1) to the
Center Connector (M2) by Bolts (HH), as per Fig 20.
-17-
AAx12 HHx2 N1x2
X4
X2
X2
X2

Step11
N1 N
O
O1
Fig 22
O2
Fig 21
Fig 21
N
AA
AA O1
O
O2
AA
Fig 22
N1
AA
O2
11. Connect the Bar-Small Top (O/O2) to the Small Top Support Bar (N), connect the Bar-Small Top
(O1/O2) to the Small Top Center Bar (N1) by Bolts (AA), as per Fig 21-Fig 22.
-18-
AAx12 Ox2 O1x2 O2x2
X4 X2

W4
M1
W1 W2 W3
W4
Fig 23
W1 W2
W1 W2
W3
AA
O1/O2
the connected shape of steel top panel
-19-
Step12
W1x2 W2x2 W3x2 W4x2
AAx16
X12
X4
12. Assemble the Small Top Panels (W1, W2, W3) in sequence, fix them on the Long Bar-Small Top
(O1/O2), then install the Small Top Panel (W4),attach on the Small Short Top Bar (O), as per Fig 23.
AA W4
O