CEL 10.8v Li-ion User manual

User Manual
10.8v Li-ion
Cordless Multi2PRO
Ion

THANK YOU
Thank you for investing in a CEL product. The 10.8v Li-Ion Cordless
Multi2PRO has been engineered and made to demanding high quality
standards; ease of operation and safety have taken a major role in
development. Proper care of your product will give you years of trouble-free
use.
Normal wear and tear, including accessory wear, is not covered under
guarantee. The product is guaranteed for domestic use against manufacturing
faults for a period of 12 months (for additional guarantee period (if any) please
refer to the store or agent from which you purchased the product or contact the
nearest authorized dealer). This product is not guaranteed for HIRE purposes.
If you have any questions, please contact us at:
[email protected]
It is possible to download updated user manuals, view demonstration videos
and find information about new products at: www.cel-global.com
Warning: User must read and understand the user manual before using the
product to reduce the risk of injury. Failure to follow all instructions may result in
electric shock, fire and/or serious personal injury. The product must be used
only for its prescribed purpose. Any use other than those mentioned in this
manual will be considered a case of misuse. The manufacturer shall NOT be
liable for any damage or injury resulting from such ases of misuse, use of force,
partially or completely dismantled appliances.
Manual Version: 2009-0A
Designed and edited in the UK
Printed in China
GETTING
STARTED
1.0 Important Safety Notes
2.0 Unpacking
3.0 Description of Parts
4.0 Battery
5.0 Charging
OPERATION
CARE
10.0 Maintenance
11.0 Storage
12.0 Environment
13.0 FAQ
14.0 Technical Specifications
6.0 Safety Notes
7.0 Fitting Tools
8.0 Tools
9.0 Operating
9.1 Overload and Low Voltage Protection
Contents

THANK YOU
Thank you for investing in a CEL product. The 10.8v Li-Ion Cordless
Multi2PRO has been engineered and made to demanding high quality
standards; ease of operation and safety have taken a major role in
development. Proper care of your product will give you years of trouble-free
use.
Normal wear and tear, including accessory wear, is not covered under
guarantee. The product is guaranteed for domestic use against manufacturing
faults for a period of 12 months (for additional guarantee period (if any) please
refer to the store or agent from which you purchased the product or contact the
nearest authorized dealer). This product is not guaranteed for HIRE purposes.
If you have any questions, please contact us at:
[email protected]
It is possible to download updated user manuals, view demonstration videos
and find information about new products at: www.cel-global.com
Warning: User must read and understand the user manual before using the
product to reduce the risk of injury. Failure to follow all instructions may result in
electric shock, fire and/or serious personal injury. The product must be used
only for its prescribed purpose. Any use other than those mentioned in this
manual will be considered a case of misuse. The manufacturer shall NOT be
liable for any damage or injury resulting from such ases of misuse, use of force,
partially or completely dismantled appliances.
Manual Version: 2009-0A
Designed and edited in the UK
Printed in China
GETTING
STARTED
1.0 Important Safety Notes
2.0 Unpacking
3.0 Description of Parts
4.0 Battery
5.0 Charging
OPERATION
CARE
10.0 Maintenance
11.0 Storage
12.0 Environment
13.0 FAQ
14.0 Technical Specifications
6.0 Safety Notes
7.0 Fitting Tools
8.0 Tools
9.0 Operating
9.1 Overload and Low Voltage Protection
Contents

Important Notes 1.0
General Power Tool Safety
Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create
sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if
your body is grounded.
c) Don’t expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or
moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of cord suitable for outdoor use reduces the risk
of electric shock.
Personal safety
a) Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use tool while tired or under the
influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
b) Use safety equipment. Always wear eye protection. Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions will reduce personal injures.
c) Avoid accidental starting. Ensure the switch is in the off-position before plugging in. Carrying tools with your finger on the switch or plugging
in power tools that have the switch on invites accidents.
d) Remove adjusting key or wrench before turning the tool on. A wrench or a key left attached to a rotating part of the tool may result in
personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loosen clothes,
jewellery or long hair can be caught in moving parts.
g) If device are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of
these devices can reduce dust-related hazards.
Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the
rate for which it was designed.
Important Notes 1.0
b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and
must be repaired.
c) Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing
accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate
the power tool. Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the
power tool's operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to
control.
g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the
work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
Battery use and care
a) Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of
fire when used with another battery pack.
b) Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
c) When battery pack is not in use, keep
it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one
terminal to another. Shorting the battery terminals together may cause burns or a fire.
d) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
Service
a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the
power tool is maintained.
Machine-specific Safety Warnings
~ Use the machine only for dry sanding. Penetration of water into the machine increases the risk of an electric shock.
~ Keep hands away from the sawing range.
Do not reach under the workpiece. Contact with the saw blade can lead to injuries.
~ Use suitable detectors to determine if utility lines are hidden in the work area or call the local utility company for assistance. Contact with
electric lines can lead to fire and electric shock. Damaging a gas line can lead to explosion. Penetrating a water line causes property damage
or may cause an electric shock.
~ When working with the machine, always hold it firmly with both hands and provide for a secure stance. The power tool is guided more
securely with both hands.
~ Secure the workpiece. A workpiece clamped with clamping devices or in a vice is held more securely than by hand.
~ Keep your workplace clean. Blends of materials are particularly dangerous. Dust from light alloys can burn or explode.
~ Avoid unintentional switching on. Ensure the On/Off switch is in the off position before inserting battery pack. Carrying the power tool with
your finger on the On/Off switch or inserting the battery pack into power tools that have the switch on invites accidents.
~ Do not open the battery. Danger of short-circuiting.
Protect the battery against heat, e.g., ~ also against continuous sun irradiation and fire. There is danger of explosion.
~ In case of damage and improper use of the battery, vapours may be emitted. Provide for fresh air and seek medical help in case of
complaints. The vapours can irritate the respiratory system.
~ When the battery is defective, liquid can escape and come into contact with adjacent components. Check any parts concerned. Clean such
parts or replace them, if required.
~ Use the battery only in conjunction with your Cel power tool. This measure alone protects the battery against dangerous overload.
~ Wear protective gloves when changing application tools/accessories.Application tools/accessories become hot after prolonged usage.
~ Do not scrape wetted materials (e. g. wall-paper) or on moist surfaces. Penetration of water into the machine increases the risk of an electric
shock.
~ Do not treat the surface to be worked with solvent-containing fluids. Materials being warmed up by the scraping can cause toxic vapours to
develop.
~ Exercise extreme caution when handling the scraper. The accessory is very sharp; danger of injury.
Always wear equipment to protect vision, hearing and lungs and suitable clothing and footwear.
Long periods of use can be harmful, take regular breaks.
Description of symbols
The rating plate on your tool may show symbols. These represent important information about the
product or instructions on its use.
General
Hazard Read Instructions
Keep Dry Keep
Bystanders
Away
Flying
Debris Sharp Blades
Protect
Eyes, Ears,
Lungs
WARNING Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to battery-operated (cordless) power tool.

Important Notes 1.0
General Power Tool Safety
Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create
sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if
your body is grounded.
c) Don’t expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or
moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of cord suitable for outdoor use reduces the risk
of electric shock.
Personal safety
a) Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use tool while tired or under the
influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
b) Use safety equipment. Always wear eye protection. Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions will reduce personal injures.
c) Avoid accidental starting. Ensure the switch is in the off-position before plugging in. Carrying tools with your finger on the switch or plugging
in power tools that have the switch on invites accidents.
d) Remove adjusting key or wrench before turning the tool on. A wrench or a key left attached to a rotating part of the tool may result in
personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loosen clothes,
jewellery or long hair can be caught in moving parts.
g) If device are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of
these devices can reduce dust-related hazards.
Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the
rate for which it was designed.
Important Notes 1.0
b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and
must be repaired.
c) Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing
accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate
the power tool. Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the
power tool's operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to
control.
g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the
work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
Battery use and care
a) Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of
fire when used with another battery pack.
b) Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
c) When battery pack is not in use, keep
it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one
terminal to another. Shorting the battery terminals together may cause burns or a fire.
d) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
Service
a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the
power tool is maintained.
Machine-specific Safety Warnings
~ Use the machine only for dry sanding. Penetration of water into the machine increases the risk of an electric shock.
~ Keep hands away from the sawing range.
Do not reach under the workpiece. Contact with the saw blade can lead to injuries.
~ Use suitable detectors to determine if utility lines are hidden in the work area or call the local utility company for assistance. Contact with
electric lines can lead to fire and electric shock. Damaging a gas line can lead to explosion. Penetrating a water line causes property damage
or may cause an electric shock.
~ When working with the machine, always hold it firmly with both hands and provide for a secure stance. The power tool is guided more
securely with both hands.
~ Secure the workpiece. A workpiece clamped with clamping devices or in a vice is held more securely than by hand.
~ Keep your workplace clean. Blends of materials are particularly dangerous. Dust from light alloys can burn or explode.
~ Avoid unintentional switching on. Ensure the On/Off switch is in the off position before inserting battery pack. Carrying the power tool with
your finger on the On/Off switch or inserting the battery pack into power tools that have the switch on invites accidents.
~ Do not open the battery. Danger of short-circuiting.
Protect the battery against heat, e.g., ~ also against continuous sun irradiation and fire. There is danger of explosion.
~ In case of damage and improper use of the battery, vapours may be emitted. Provide for fresh air and seek medical help in case of
complaints. The vapours can irritate the respiratory system.
~ When the battery is defective, liquid can escape and come into contact with adjacent components. Check any parts concerned. Clean such
parts or replace them, if required.
~ Use the battery only in conjunction with your Cel power tool. This measure alone protects the battery against dangerous overload.
~ Wear protective gloves when changing application tools/accessories.Application tools/accessories become hot after prolonged usage.
~ Do not scrape wetted materials (e. g. wall-paper) or on moist surfaces. Penetration of water into the machine increases the risk of an electric
shock.
~ Do not treat the surface to be worked with solvent-containing fluids. Materials being warmed up by the scraping can cause toxic vapours to
develop.
~ Exercise extreme caution when handling the scraper. The accessory is very sharp; danger of injury.
Always wear equipment to protect vision, hearing and lungs and suitable clothing and footwear.
Long periods of use can be harmful, take regular breaks.
Description of symbols
The rating plate on your tool may show symbols. These represent important information about the
product or instructions on its use.
General
Hazard Read Instructions
Keep Dry Keep
Bystanders
Away
Flying
Debris Sharp Blades
Protect
Eyes, Ears,
Lungs
WARNING Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to battery-operated (cordless) power tool.

Unpacking 2.0
NOTE
Due to modern mass production techniques, it is unlikely that your
power tool is faulty or that apart is missing. If you find anything
wrong, do not operate the tool until the parts have been replaced or
the fault has been rectified. Failure to do so could result in serious
personal Injury.
Description of Parts 3.0
Read all safety warnings and all
instructions.
Failure to follow the warnings and
instructions may result in electric shock, fire
and/or serious injury.
Intended Use
The machine is intended for sawing and
cutting -using the specified accessories-
wooden materials, plastic, gypsum, non-
ferrous metals and fastening elements (e.g.
nails, staples). It is also suitable for working
soft wall tiles as well as for dry sanding and
scraping of small surfaces. It is especially
suitable for working close to edges and for
flush cutting.
Charger Unit
Hex Key
Locking Bolt
Blade Adaptor Washer
Locking Washer
Universal Saw MT1-AC11
Scraper MT1-AC14
Sanding Pad MT1-AC09
3x Sanding Sheets
Li-Ion Battery
MT1 Multi2PRO
This User Manual

Unpacking 2.0
NOTE
Due to modern mass production techniques, it is unlikely that your
power tool is faulty or that apart is missing. If you find anything
wrong, do not operate the tool until the parts have been replaced or
the fault has been rectified. Failure to do so could result in serious
personal Injury.
Description of Parts 3.0
Read all safety warnings and all
instructions.
Failure to follow the warnings and
instructions may result in electric shock, fire
and/or serious injury.
Intended Use
The machine is intended for sawing and
cutting -using the specified accessories-
wooden materials, plastic, gypsum, non-
ferrous metals and fastening elements (e.g.
nails, staples). It is also suitable for working
soft wall tiles as well as for dry sanding and
scraping of small surfaces. It is especially
suitable for working close to edges and for
flush cutting.
Charger Unit
Hex Key
Locking Bolt
Blade Adaptor Washer
Locking Washer
Universal Saw MT1-AC11
Scraper MT1-AC14
Sanding Pad MT1-AC09
3x Sanding Sheets
Li-Ion Battery
MT1 Multi2PRO
This User Manual

Battery 4.0
WARNING, Do not throw used batteries into fire or water, It could cause
an explosion!
WARNING, Do not use an extension cord.
WARNING. Charge indoors only.
Please dispose of batteries at your local battery disposal depot.
Note: The battery is
supplied partially charged.
To ensure full capacity of
the battery, completely
charge the battery in the
battery charger before
first use.
CHARGER LIGHTS INDICATOR
Battery charge indicator
1. Place the charger in asafe position
away from moisture, heat or any hazard
to the charger or other danger.
2.Connect to suitable power outlet and
switch on.
3. Turn the battery so the rails slide
smoothly into place on the charger.
Two solid GREEN LED’s show mains
connection.
One solid GREEN & one solid RED LED,
shows fast charging.
When two GREEN LED show again
battery is charged.
Two fast flashing GREEN LED show,
there is a charging problem.
The lithium ion battery can be charged at
any time without reducing its service life.
Interrupting the charging procedure does not
damage the battery.
The battery circuitry will allow charging only
within a temperature range of 0 °C to 45 °C
It is normal for the battery charger to
hum and be warm but not hot during
operation.
Unplug the charger when not in use and
store it in adry, secure place. Always
remove the battery Pack and store it in a
dry, secure place when the trimmer is
not in use.
Always charge the battery before storage
this prevents excessive discharge which
can damage the battery.
Never leave the battery on the charger
longer than 24 hours due to fire risk.
Charging 5.0
Charging 5.0
GREEN
FULL
YELLOW
HALF
RED
EMPTY
Inserting the Battery
Insert the charged battery into the handle
until it can be felt to engage and sits flush
against the handle.
Removing the Battery
To remove the battery, press the unlocking
buttons and pull the battery out of the
machine to the rear. Do not exert any force.
WARNING Use only the battery charger
supplied with this tool or an identical
replacement. Use only original Cel lithium
ion batteries with the voltage listed on the
nameplate of your power tool. Other
batteries or chargers can cause damage or
injury.
The Li-ion battery is protected against deep discharging by
the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
circuit.
If the machine should automatically switch off.Allow the
battery to cool then charge it before restarting the machine.
Otherwise the battery can become damaged.
Only use
supplied
battery and
charger or
identical
replacements.
POWER ON GREEN+GREEN
CHARGED GREEN+GREEN
CHARGING GREEN+RED
ERROR FLASHING GREEN

Battery 4.0
WARNING, Do not throw used batteries into fire or water, It could cause
an explosion!
WARNING, Do not use an extension cord.
WARNING. Charge indoors only.
Please dispose of batteries at your local battery disposal depot.
Note: The battery is
supplied partially charged.
To ensure full capacity of
the battery, completely
charge the battery in the
battery charger before
first use.
CHARGER LIGHTS INDICATOR
Battery charge indicator
1. Place the charger in asafe position
away from moisture, heat or any hazard
to the charger or other danger.
2.Connect to suitable power outlet and
switch on.
3. Turn the battery so the rails slide
smoothly into place on the charger.
Two solid GREEN LED’s show mains
connection.
One solid GREEN & one solid RED LED,
shows fast charging.
When two GREEN LED show again
battery is charged.
Two fast flashing GREEN LED show,
there is a charging problem.
The lithium ion battery can be charged at
any time without reducing its service life.
Interrupting the charging procedure does not
damage the battery.
The battery circuitry will allow charging only
within a temperature range of 0 °C to 45 °C
It is normal for the battery charger to
hum and be warm but not hot during
operation.
Unplug the charger when not in use and
store it in adry, secure place. Always
remove the battery Pack and store it in a
dry, secure place when the trimmer is
not in use.
Always charge the battery before storage
this prevents excessive discharge which
can damage the battery.
Never leave the battery on the charger
longer than 24 hours due to fire risk.
Charging 5.0
Charging 5.0
GREEN
FULL
YELLOW
HALF
RED
EMPTY
Inserting the Battery
Insert the charged battery into the handle
until it can be felt to engage and sits flush
against the handle.
Removing the Battery
To remove the battery, press the unlocking
buttons and pull the battery out of the
machine to the rear. Do not exert any force.
WARNING Use only the battery charger
supplied with this tool or an identical
replacement. Use only original Cel lithium
ion batteries with the voltage listed on the
nameplate of your power tool. Other
batteries or chargers can cause damage or
injury.
The Li-ion battery is protected against deep discharging by
the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
circuit.
If the machine should automatically switch off.Allow the
battery to cool then charge it before restarting the machine.
Otherwise the battery can become damaged.
Only use
supplied
battery and
charger or
identical
replacements.
POWER ON GREEN+GREEN
CHARGED GREEN+GREEN
CHARGING GREEN+RED
ERROR FLASHING GREEN

Safety Notes Before Starting Work 6.0
Sharp blades, heat buildup and flying
debris are a danger to user and
bystanders. Use of suitable
protective clothing, gloves, footwear,
eye and ear protection as well as
safe working practices can reduce
these risks.
Dusts from materials such
as lead-containing coatings,
some wood types, minerals
and metal can be harmful to one's
health. Touching or breathing-in the
dusts can cause allergic reactions
and/or lead to respiratory infections
of the user or bystanders.
Certain dusts, such as oak or beech
dust, are considered as
carcinogenic, especially in
connection with wood-treatment
additives (chromate, wood
preservative).
Materials containing asbestos may
only be worked by specialists.
- Use dust extraction whenever
possible.
- Provide for good ventilation of the
working place.
- It is recommended to wear a P2
filter class respirator.
Observe the relevant regulations
in your country for the materials
to be worked
Do not cover the venting slots of the
machine while working, as this
reduces the working life of the
machine.
Friction from the tool can cause
the accessories to become hot,
this can be reduced by moving the
blade around on the workpiece.
This also helps to clear swarf
buildup.
This tool vibrates at very high
frequency. Regular breaks must be
taken to reduce the chance of injury.
At the first sign of discomfort work
should immediately cease.
Fitting Tools 7.0
If required, remove
an already mounted
application
tool/accessory.
Loosen the screw
with the hex key and
remove the
tool/accessory. Be
sure to clear any
debris.
Mount the suitable
tool/accessory in
such a manner on
the tool holder that
the offset faces
downward.
Turn the
tool/accessory to a
position favourable for
the respective job, and allow it to engage
into the cams of the tool holder. 12 different
positions are possible, each offset by 30°.
Fasten the tool/accessory with Locking Bolt
and Washer. Tighten the bolt with Hex key
until the washer and bolt are flush with the
tool/accessory and firmly fixed.
The sanding plates
are fitted with Velcro
backing for quick
and easy fastening
of sanding sheets
with Velcro
adhesion.
Before attaching the
sanding sheet , free
the Velcro backing of
the sanding plate
from any debris by
tapping to enable
optimum adhesion.
Position the sanding
sheet flush
alongside one edge
of the sanding plate,
then lay the sanding
sheet onto the sanding plate and press
firmly.
To remove the sanding sheet, grasp it at one
of the tips and pull it off from the sanding
plate.
Check the tight seating of the tool/accessory while fitting and
regularly while working there is a risk they can come loose
during operation and be damaged or hazardous .

Safety Notes Before Starting Work 6.0
Sharp blades, heat buildup and flying
debris are a danger to user and
bystanders. Use of suitable
protective clothing, gloves, footwear,
eye and ear protection as well as
safe working practices can reduce
these risks.
Dusts from materials such
as lead-containing coatings,
some wood types, minerals
and metal can be harmful to one's
health. Touching or breathing-in the
dusts can cause allergic reactions
and/or lead to respiratory infections
of the user or bystanders.
Certain dusts, such as oak or beech
dust, are considered as
carcinogenic, especially in
connection with wood-treatment
additives (chromate, wood
preservative).
Materials containing asbestos may
only be worked by specialists.
- Use dust extraction whenever
possible.
- Provide for good ventilation of the
working place.
- It is recommended to wear a P2
filter class respirator.
Observe the relevant regulations
in your country for the materials
to be worked
Do not cover the venting slots of the
machine while working, as this
reduces the working life of the
machine.
Friction from the tool can cause
the accessories to become hot,
this can be reduced by moving the
blade around on the workpiece.
This also helps to clear swarf
buildup.
This tool vibrates at very high
frequency. Regular breaks must be
taken to reduce the chance of injury.
At the first sign of discomfort work
should immediately cease.
Fitting Tools 7.0
If required, remove
an already mounted
application
tool/accessory.
Loosen the screw
with the hex key and
remove the
tool/accessory. Be
sure to clear any
debris.
Mount the suitable
tool/accessory in
such a manner on
the tool holder that
the offset faces
downward.
Turn the
tool/accessory to a
position favourable for
the respective job, and allow it to engage
into the cams of the tool holder. 12 different
positions are possible, each offset by 30°.
Fasten the tool/accessory with Locking Bolt
and Washer. Tighten the bolt with Hex key
until the washer and bolt are flush with the
tool/accessory and firmly fixed.
The sanding plates
are fitted with Velcro
backing for quick
and easy fastening
of sanding sheets
with Velcro
adhesion.
Before attaching the
sanding sheet , free
the Velcro backing of
the sanding plate
from any debris by
tapping to enable
optimum adhesion.
Position the sanding
sheet flush
alongside one edge
of the sanding plate,
then lay the sanding
sheet onto the sanding plate and press
firmly.
To remove the sanding sheet, grasp it at one
of the tips and pull it off from the sanding
plate.
Check the tight seating of the tool/accessory while fitting and
regularly while working there is a risk they can come loose
during operation and be damaged or hazardous .

Tools 8.0
Carbide Grit
Semicircle Saw
Blade 2 1/2"
Diamond-Coated
Semicircle Saw
Blade 2 1/2"
35mm (1 3/8")
End Cut
35mm (1 3/8")
Universal End Cut
10mm End Cut
3 1/8" Segment
Saw Blade
Removing grout, cutting and shaping plaster,
porous concrete and masonry. Flat on one
side so you can cut into corners and flush
against adjoining surfaces.
Removing grout, cutting and shaping plaster,
porous concrete and masonry. Scoring and
cutting for a precise fit. Flat on one side so
you can cut into corners and flush against
adjoining surfaces.
Plunge cutting up to 1-5/8" depth. Hardened
teeth will cut non-ferrous metals.
Plunge cutting up to 1-5/8" depth. Hardened
teeth will cut ferrous metals.(wood, plastic
etc)
Plunge cutting up to 30mm depth. Hardened
teeth will cut non-ferrous metals.
Linear and Plunge cutting. Flat on one side
so you can cut into corners and flush against
adjoining surfaces.
Saw
MT1-AC01
MT1-AC02
MT1-AC12
MT1-AC11
MT1-AC15
MT1-AC13
More tools and uses are available at www.cel-global.com
Please let us know if you have any ideas or new uses for the Multi2PRO
Tools 8.0
Sand & Polish
MT1-AC03
MT1-AC04
Sanding Pad
Sanding Pack
Sanding Finger
Pad
Sanding Finger
Sheet
Polishing Pad
Holds sanding sheet for detailed sanding in
small areas and corners.
Universal sanding applications. Fits MT1-AC09
80, 120, 180G 6PCS of each
Holds sanding sheets for detailed sanding in
very small areas and corners. Thinner so it
reaches into small openings.
Universal sanding applications. Fits MT1-AC07
40, 80, 120, 180, 220G 6 pcs each
Soft felt buffing and polishing pad
Rasp
Carbide Rasp
Finger
Triangular Carbide
Rasp
Coarse grinding or rasping, aggressive material
removal in small, tight areas.
Coarse grinding or rasping, aggressive material
removal over larger areas.
Stainless Steel
Scraper Removing old vinyl, wood or other floor
coverings, paint and coatings, residues and
separating laminated layers, cuts carpet.
Scrape
MT1-AC09
MT1-AC10
MT1-AC06
MT1-AC07
MT1-AC16
MT1-AC14

Tools 8.0
Carbide Grit
Semicircle Saw
Blade 2 1/2"
Diamond-Coated
Semicircle Saw
Blade 2 1/2"
35mm (1 3/8")
End Cut
35mm (1 3/8")
Universal End Cut
10mm End Cut
3 1/8" Segment
Saw Blade
Removing grout, cutting and shaping plaster,
porous concrete and masonry. Flat on one
side so you can cut into corners and flush
against adjoining surfaces.
Removing grout, cutting and shaping plaster,
porous concrete and masonry. Scoring and
cutting for a precise fit. Flat on one side so
you can cut into corners and flush against
adjoining surfaces.
Plunge cutting up to 1-5/8" depth. Hardened
teeth will cut non-ferrous metals.
Plunge cutting up to 1-5/8" depth. Hardened
teeth will cut ferrous metals.(wood, plastic
etc)
Plunge cutting up to 30mm depth. Hardened
teeth will cut non-ferrous metals.
Linear and Plunge cutting. Flat on one side
so you can cut into corners and flush against
adjoining surfaces.
Saw
MT1-AC01
MT1-AC02
MT1-AC12
MT1-AC11
MT1-AC15
MT1-AC13
More tools and uses are available at www.cel-global.com
Please let us know if you have any ideas or new uses for the Multi2PRO
Tools 8.0
Sand & Polish
MT1-AC03
MT1-AC04
Sanding Pad
Sanding Pack
Sanding Finger
Pad
Sanding Finger
Sheet
Polishing Pad
Holds sanding sheet for detailed sanding in
small areas and corners.
Universal sanding applications. Fits MT1-AC09
80, 120, 180G 6PCS of each
Holds sanding sheets for detailed sanding in
very small areas and corners. Thinner so it
reaches into small openings.
Universal sanding applications. Fits MT1-AC07
40, 80, 120, 180, 220G 6 pcs each
Soft felt buffing and polishing pad
Rasp
Carbide Rasp
Finger
Triangular Carbide
Rasp
Coarse grinding or rasping, aggressive material
removal in small, tight areas.
Coarse grinding or rasping, aggressive material
removal over larger areas.
Stainless Steel
Scraper Removing old vinyl, wood or other floor
coverings, paint and coatings, residues and
separating laminated layers, cuts carpet.
Scrape
MT1-AC09
MT1-AC10
MT1-AC06
MT1-AC07
MT1-AC16
MT1-AC14

Operating 9.0Operating 9.0
Switching On and Off
To start the machine, push
the On/Off switch forward
so that "ON" is indicated
on the switch.
To switch off the machine,
push the On/Off switch
toward the rear so that the
"OFF" is indicated on the
switch.
Selecting the rate of oscillation
Use the thumbwheel to select
the rate of oscillation.
The required rate of oscillation
depends on the material and
the working conditions
and can be determined
through practical testing.
Sawing
~ Use undamaged faultless
saw blades only.
Deformed, blunt saw blades or
saw blades that are otherwise
damaged can break or shatter.
~ When sawing light building
materials, observe the statutory
provisions and the recommendations
of the material suppliers.
~ Plunge cuts may only be
applied to soft materials, such
as wood, gypsum plaster
boards, etc.
Before sawing with
MT1-AC12 saw blades
in wood, particle board,
building materials, etc.,
check these for foreign
objects such as nails,
screws, or similar. If required,
remove foreign objects or use
MT1-AC11 saw blades.
Separating
Note: When separating wall
tiles take into consideration
that the application
tools/accessories wear heavily
when used for longer periods
of time.
Sanding
The removal rate and the sanding
pattern are primarily determined by
the choice of sanding sheet, the
preset oscillation rate and the
applied pressure.
Flawless sanding sheets achieve the
best sanding capacity and extend the
service life of the machine.
Try to apply uniform sanding
pressure; this increases the working
life of the sanding sheets.
Additional pressure does not lead to
an increased sanding capacity, only
increased wear of the machine and
the sanding sheet.
For precise on-the-spot sanding of
edges, corners and hard to reach
areas, it is also possible to work only
with the tip or an edge of the sanding
plate.
When selectively sanding on the
spot, the sanding sheet can heat up
considerably. Reduce the oscillation
rate and allow the sanding sheet to
cool down regularly.
A sanding sheet that has been used
for metal should not be used for
other materials.
Use only original CEL sanding
accessories.
Scraping
For scraping, select a high oscillation
rate. Work on a soft surface (e.g.
wood) at a flat angle, and apply only
light pressure. Otherwise the scraper
can cut into the surface.
Sharp blades, heat buildup and
flying debris are a danger to user
and bystanders. Use of suitable
protective clothing, gloves,
footwear, eye and ear protection
as well as safe working practices
can reduce these risks.
OFF
ON

Operating 9.0Operating 9.0
Switching On and Off
To start the machine, push
the On/Off switch forward
so that "ON" is indicated
on the switch.
To switch off the machine,
push the On/Off switch
toward the rear so that the
"OFF" is indicated on the
switch.
Selecting the rate of oscillation
Use the thumbwheel to select
the rate of oscillation.
The required rate of oscillation
depends on the material and
the working conditions
and can be determined
through practical testing.
Sawing
~ Use undamaged faultless
saw blades only.
Deformed, blunt saw blades or
saw blades that are otherwise
damaged can break or shatter.
~ When sawing light building
materials, observe the statutory
provisions and the recommendations
of the material suppliers.
~ Plunge cuts may only be
applied to soft materials, such
as wood, gypsum plaster
boards, etc.
Before sawing with
MT1-AC12 saw blades
in wood, particle board,
building materials, etc.,
check these for foreign
objects such as nails,
screws, or similar. If required,
remove foreign objects or use
MT1-AC11 saw blades.
Separating
Note: When separating wall
tiles take into consideration
that the application
tools/accessories wear heavily
when used for longer periods
of time.
Sanding
The removal rate and the sanding
pattern are primarily determined by
the choice of sanding sheet, the
preset oscillation rate and the
applied pressure.
Flawless sanding sheets achieve the
best sanding capacity and extend the
service life of the machine.
Try to apply uniform sanding
pressure; this increases the working
life of the sanding sheets.
Additional pressure does not lead to
an increased sanding capacity, only
increased wear of the machine and
the sanding sheet.
For precise on-the-spot sanding of
edges, corners and hard to reach
areas, it is also possible to work only
with the tip or an edge of the sanding
plate.
When selectively sanding on the
spot, the sanding sheet can heat up
considerably. Reduce the oscillation
rate and allow the sanding sheet to
cool down regularly.
A sanding sheet that has been used
for metal should not be used for
other materials.
Use only original CEL sanding
accessories.
Scraping
For scraping, select a high oscillation
rate. Work on a soft surface (e.g.
wood) at a flat angle, and apply only
light pressure. Otherwise the scraper
can cut into the surface.
Sharp blades, heat buildup and
flying debris are a danger to user
and bystanders. Use of suitable
protective clothing, gloves,
footwear, eye and ear protection
as well as safe working practices
can reduce these risks.
OFF
ON

Maintenance 10.0
WARNING, Switch off and remove the battery before carrying out any
maintenance on the tool.
General inspection
Regularly check that all the fixing screws are present and tight. They may
vibrate loose over time.
Dust
Keep the tool'sair vents unclogged and clean at all times.
Remove dust and dirt regularly.
Cleaning is best done with compressed air or arag.
Never use caustic agents to clean plastic parts.
CAUTION, Do not use cleaning agents to clean the plastic parts of the tool. A
mild detergent on adamp cloth is recommended. Water must never come into
contact with the tool.
Storage 11.0
Environment 12.0
Store the tool, instruction manual and accessories in asecure, dry place. In
this way you will always have all the information and parts ready to hand.
Never store the tool with a flat battery.
The battery should ideally be stored between 10ºC and 24ºC (50ºF) and (75ºF).
When the time comes to dispose of this product please consider the environment
and take it to a recognised recycling facility instead of disposing with general
household waste.
The trimmer uses a Lithium Ion (Li-Ion) battery which must be disposed of properly.
Call your local council, civic amenity site, or recycling centre for information on the
recycling and disposal of electrical products and Lithium Ion (Li-Ion) batteries.
Overload and Low Voltage Protection 9.1
Overload Protection
When the unit is overloaded (e.g.: the product is working too hard or the blade is
jammed) the current will increase rapidly, this triggers the auto cut-off, indicated by
a RED flashing LED. To reset, slide the power switch to the “OFF” position and
restart again after re-adjusting to a proper cutting pressure/angle as well as
choosing a higher torque setting.
Low Voltage Protection
When the discharging current is too high or the remaining battery voltage is not
enough to drive the machine, the power supply stop automatically and the LED
lights will go out. To reset, slide the power switch to “OFF” position and restart.
Note: If this happens frequently the battery capacity is low, please recharge your
battery.

Maintenance 10.0
WARNING, Switch off and remove the battery before carrying out any
maintenance on the tool.
General inspection
Regularly check that all the fixing screws are present and tight. They may
vibrate loose over time.
Dust
Keep the tool'sair vents unclogged and clean at all times.
Remove dust and dirt regularly.
Cleaning is best done with compressed air or arag.
Never use caustic agents to clean plastic parts.
CAUTION, Do not use cleaning agents to clean the plastic parts of the tool. A
mild detergent on adamp cloth is recommended. Water must never come into
contact with the tool.
Storage 11.0
Environment 12.0
Store the tool, instruction manual and accessories in asecure, dry place. In
this way you will always have all the information and parts ready to hand.
Never store the tool with a flat battery.
The battery should ideally be stored between 10ºC and 24ºC (50ºF) and (75ºF).
When the time comes to dispose of this product please consider the environment
and take it to a recognised recycling facility instead of disposing with general
household waste.
The trimmer uses a Lithium Ion (Li-Ion) battery which must be disposed of properly.
Call your local council, civic amenity site, or recycling centre for information on the
recycling and disposal of electrical products and Lithium Ion (Li-Ion) batteries.
Overload and Low Voltage Protection 9.1
Overload Protection
When the unit is overloaded (e.g.: the product is working too hard or the blade is
jammed) the current will increase rapidly, this triggers the auto cut-off, indicated by
a RED flashing LED. To reset, slide the power switch to the “OFF” position and
restart again after re-adjusting to a proper cutting pressure/angle as well as
choosing a higher torque setting.
Low Voltage Protection
When the discharging current is too high or the remaining battery voltage is not
enough to drive the machine, the power supply stop automatically and the LED
lights will go out. To reset, slide the power switch to “OFF” position and restart.
Note: If this happens frequently the battery capacity is low, please recharge your
battery.

FAQ 13.0
Do I need to fully discharge the battery
before recharging it?
No the Li-Ion system has no memory effect so
you can charge it at any time. The charge will be
retained in storage for much longer than older
battery technology.
My battery is not charging, what’s
wrong?
Check to make sure the electrical outlet is
"live"and that the air surrounding the battery
and charger is between
Make sure the battery is correctly
fitted.
In case of excessive loading or when exceeding
the allowable battery temperature range of 0-70
°C, the speed is reduced or the machine switches
off. In case of reduced speed, the machine will
not run at full speed until after reaching the
allowable battery temperature again. In case of
automatic shut-off, switch the machine off, allow
the battery to cool down and then switch the
machine on again.
Why does my Multi2PRO stop
sometimes?
The Multi2PRO wont start, what’s wrong?
a)Clean as described in the maintenance section.
b)Check the battery is charged and properly
fitted, also make sure the switch and speed
control are working and being operated correctly.
10ºC and 24ºC (50ºF)
and (75ºF).
See above.
If the blade jams the tool will switch off to protect
the circuits within. Turn off, wait, then turn on
again.
Why cant I cut/sand as well as
demonstrated?
Grip the tool firmly, the oscillations can be
absorbed by your arm and wrist reducing the
effective cut.
Make sure the cutting tool is in good condition
and the battery is charged.
Don't press the tool too hard, let the accessory do
the work.
Keep moving the blade around in the cut to clear
swarf as this will hinder the cut and cause heat
buildup.
Where should I keep my Multi2PRO?
In a dry place at a stable temperature
What should I do if my Multi2PRO gets
wet?
Dry fully for several days in a warm but not hot
place before trying to charge or use.
How can I get my Multi2PRO repaired if it
is damaged?
Contact your retailer.
Where do I find my serial number?
On the left hand side of the body.
Where can I get replacement parts,
advice or help?
Ask at your retailer or visit www.cel-global.com
How long is the warranty and what is
covered?
Please see inside cover
between
10ºC and 24ºC (50ºF and 75ºF). Charge and
remove the battery before storage.
Technical Specifications 14.0
If you experience any problems with the product please contact
email: [email protected]
phone UK: [phone]
www.cel-global.com
©Copyright C Enterprise Limited 2009
3061583
C Enterprise Limited
READ INSTRUCTION MANUAL
BEWARE OF FLYING
OBJECTS AND DEBRIS
GENERAL HAZARD
SAFETY ALERT
KEEP BYSTANDERS AWAY
Unit operating time cycle with full battery
Oscillating speed
Sound Pressure Level (dB(A))
Battery operating voltage
Battery makeup
Charging period for fully discharged battery
Charger Input
Charger Output
Dimensions
Weight
Product Code
Oscillation angle
- 25 minutes with no load
- 5000 - 19000rpm
- 10.8V DC (3 cells)
- Lithium Ion (Li-ion) 1300mAh
- Approx. 60 mins
- 100-240vAC 50/60Hz
- 10.8V DC 1.8A
- 353x266x95mm
- approx (14x10x4")
- 0.88Kg (1.9lbs) (not including charger)
- MT1
- 3.2°
- 86dB

FAQ 13.0
Do I need to fully discharge the battery
before recharging it?
No the Li-Ion system has no memory effect so
you can charge it at any time. The charge will be
retained in storage for much longer than older
battery technology.
My battery is not charging, what’s
wrong?
Check to make sure the electrical outlet is
"live"and that the air surrounding the battery
and charger is between
Make sure the battery is correctly
fitted.
In case of excessive loading or when exceeding
the allowable battery temperature range of 0-70
°C, the speed is reduced or the machine switches
off. In case of reduced speed, the machine will
not run at full speed until after reaching the
allowable battery temperature again. In case of
automatic shut-off, switch the machine off, allow
the battery to cool down and then switch the
machine on again.
Why does my Multi2PRO stop
sometimes?
The Multi2PRO wont start, what’s wrong?
a)Clean as described in the maintenance section.
b)Check the battery is charged and properly
fitted, also make sure the switch and speed
control are working and being operated correctly.
10ºC and 24ºC (50ºF)
and (75ºF).
See above.
If the blade jams the tool will switch off to protect
the circuits within. Turn off, wait, then turn on
again.
Why cant I cut/sand as well as
demonstrated?
Grip the tool firmly, the oscillations can be
absorbed by your arm and wrist reducing the
effective cut.
Make sure the cutting tool is in good condition
and the battery is charged.
Don't press the tool too hard, let the accessory do
the work.
Keep moving the blade around in the cut to clear
swarf as this will hinder the cut and cause heat
buildup.
Where should I keep my Multi2PRO?
In a dry place at a stable temperature
What should I do if my Multi2PRO gets
wet?
Dry fully for several days in a warm but not hot
place before trying to charge or use.
How can I get my Multi2PRO repaired if it
is damaged?
Contact your retailer.
Where do I find my serial number?
On the left hand side of the body.
Where can I get replacement parts,
advice or help?
Ask at your retailer or visit www.cel-global.com
How long is the warranty and what is
covered?
Please see inside cover
between
10ºC and 24ºC (50ºF and 75ºF). Charge and
remove the battery before storage.
Technical Specifications 14.0
If you experience any problems with the product please contact
email: [email protected]
phone UK: [phone]
www.cel-global.com
©Copyright C Enterprise Limited 2009
3061583
C Enterprise Limited
READ INSTRUCTION MANUAL
BEWARE OF FLYING
OBJECTS AND DEBRIS
GENERAL HAZARD
SAFETY ALERT
KEEP BYSTANDERS AWAY
Unit operating time cycle with full battery
Oscillating speed
Sound Pressure Level (dB(A))
Battery operating voltage
Battery makeup
Charging period for fully discharged battery
Charger Input
Charger Output
Dimensions
Weight
Product Code
Oscillation angle
- 25 minutes with no load
- 5000 - 19000rpm
- 10.8V DC (3 cells)
- Lithium Ion (Li-ion) 1300mAh
- Approx. 60 mins
- 100-240vAC 50/60Hz
- 10.8V DC 1.8A
- 353x266x95mm
- approx (14x10x4")
- 0.88Kg (1.9lbs) (not including charger)
- MT1
- 3.2°
- 86dB

C Enterprise Limited www.cel-global.com [email protected]
UK HK USA China Europe Australia Japan• • • • • •
C Enterprise Ltd