Celestica Athena Erp lot9 EcoDesign User manual

P2522 Athena
Erp lot9 EcoDesign
V0.2

2
Preface
This documentation addresses European Union (EU) Ecodesign requirements for
servers and storage products. All data and ratings within this file are in reference
onl y to CLS P2522 product(s). The below information conforms with requirements
laid down in Annex II of the Commission Regulation 2019/424.
3(1)(a): Product type: Dual node Flash Storage Controller.
3(1)(b): manufacturer’s address:
Celestica (Thailand) Co.,Ltd
49/18 Laem Chabang Industrial Estate, Moo 5, Tungsukhla
Siracha, Chonburi 20230, Thailand.
3(1)(c): product model number: P2522.
3(1)(d): See the serial number on the physical system to determine the year of
manufacture.
3(1)(e-j): PSU Efficiency and Power Factor Value (Table) (From 80 Plu report)
P2522 PSU meets from 1 Mar 2020:
PSU Model #: CPR02021-2M16 Watt : 2000W
Sy tem (EUT) Efficiency in Idle State Power (Table)
Repre entative
Configuration
Mea ured Idle State Power
(W)
Calculated Idle Power
Allowance (W)
High
-
End Performance
Configuration
Typical Configuration
（ with24 NVMe SSD and
105W CPU with 6 memory ）
660W N/A
Lo
-
End Performance
Configuration

3
Sy tem (EUT) Efficiency in Active State Power (Table)
Repre entative
Configuration
Mea ured Active
State
Power (W)
Calculated
A
ctive
Power
Allowance (W)
High
-
End Performance
Configuration
Typical Configuration
（ with24 NVMe SSD and
105W CPU with 6 memory ）
1350W N/A
Lo
-
End Performance
Configuration
3(1)(k):
This product has been tested in order to verify that it ill function ithin the
boundaries (such as temperature and humidity) of the declared operating condition
class: A2.
3(1)(n): FW and Secure data Deletion tool
To delete data safely need the OS level software to be handled by Celestica's
customer.
Celestica will support firmware per Erp requirements at "free of charge or at a fair,
transparent and non-discriminatory cost.”

4
Website including to download the FW: https://hardware-support.azurewebsites.net/
3(3)(a):
BBU Cobalt: above 25G
Neodymium in the PM1733 HDDs: between 5g-25g

5
3(3)(b): System Disassembly Instructions
CAUTION: Always power off the system and unplug the power cord(s) first before
disassembling the system!
CPU
Type and number of fastenings: Four (4) T30 screws on heatsink.
Tools required: Screwdriver with T30 Torx bit. The screw torque should be
13 KGF.CM.
Procedure:
Step 1: Disassemble the Heatsink.
1) Use a T30 screw driver. The screw torque should be 13 KGF.CM.
2) Disassembly must be followed by 4,3,2,1 order, see the label on the
heatsink.
Step 2: Disassemble the CPU.
1) Then disassemble the CPU from the motherboard.
Figure 3- 1: Install the CPU

6
WARNING:
For Sharp edges and corners, please avoid injure when do assembling and dis-assembling operation.

7
Hard Drive
Type and number of fastenings: One (1) latch and four (4) Pan Head screw M3 x L4.5.
Torque 4 ± 0.5 KGF.CM .
Tools required: Screwdriver with PH2 bit.
Procedure:
1) Click the button ① ,
2) The handle will open automatically ② ,
3) Hold the handle to pull the drive out of the chassis ③ .
4) Remove the screws and then remove the HDD from the carrier.

8
PSU
Type and number of fastenings: One (1) latch and one (1) handle per module.
Tools required: None.
Procedure:
1) Rotate the handle to a suitable angle
①
;
2) Keep pressing the pick and holding the handle ② ;
3) Pull the PSU out of the chassis ③ .

9
Controller Canister
Type and number of fastenings: Two (2) latches per controller canister.
Tools required: None.
Procedure: Rotate the handle then hold the handle to pull the canister out of the
chassis.

10
Controller canister cover
NOTE: The system should be operated by a skilled man after training.
Type and number of fastenings: Two (2) locks on the controller canister cover.
Tools required: None.
Procedure: Press the two locks and pull the controller canister cover out in the
direction as shown below.