Cell2 SAS32R-MS User manual

SAS32R-MS
DUAL SPEAKER SIREN SYSTEM W/
3-BUTTON CONTROL SWITCH
& MIC SET
NOTICE TO INSTALLER
Before installation and operation ― read all instructions and warnings.
Deliver this manual to the end user of this equipment.
Installation & Operation Manual

INSTALLATION............................................................................................................ 2
MOUNTING.................................................................................................................. 3
WIRING........................................................................................................................ 5
CONTROLLER FUNCTION......................................................................................... 6
PA BROADCAST......................................................................................................... 6
TONE GROUP PROGRAMMING................................................................................ 7
TABLE OF CONTENTS
- 1 -

INSTALLATION
Proper installation of the product requires the installer to have a good understanding of
automotive electronics, systems and procedures. It is essential to install the unit
properly to ensure safe and reliable operation.
Please read through all instructions thoroughly and carefully before installing the unit.
Failure to follow these instructions could result in serious damage to the unit or vehicle
and may void warranties.
The correct mounting and wiring is the key to the effectiveness of the Siren System.
Installers must read and follow installation instructions and warnings in the manual from
the original manufacturer.
The operator should verify the siren system is fastened to the vehicle securely and is
functioning properly. Failure to follow all safety precautions and instructions may cause
property damage, injury, or death.
Ensure that any switch control panel is located in an area that allows both the vehicle
and the control panel to be operated safely in any driving condition.
WARNING Sound Hazard - Sound level from siren speaker (109dB at 2M) may cause hearing damage.
Do not operate siren without adequate hearing protection for you and anyone in immediate vicinity.
(Ref. OSHA 1910.95 for occupational noise exposure guidelines)
CONTENTS: The installer must have good knowledge of electricity, vehicle electrical
systems and emergency equipment. Always seek professional assistance if in doubt.
- 2 -

MOUNTING
Speaker Siren Unit
Secure the mounting bracket to an appropriate and suitable area.
RUBBER PAD
BRACKET
FLAT WASHER
SPRING WASHER
M6 HEX HEAD NACHIRE BOLT
RUBBER
MOUNTING BRACKET
FLAT WASHER
SPRING WASHER
0.590" Maximum
0.511" Minimum
Permanent mounting of this product may require drilling. It is necessary to make
sure that no other vehicle components could be damaged by this process.
Check both sides of the mounting surface before drilling.
Siren Speaker must only be mounted horizontally to the ground. Fail to follow
may cause undesired water to ingress into speaker, damage to the product and
void the warranty.
WARNING
- 3 -
Note: Please only mount the horn facing
out horizontally to the ground.

When installing surface mount, make sure to consider the thickness of the mounting
surface and washer. The installer must use the supplied screws to match the rear
threaded insert of the Switch Panel. Fail to do so may cause damage to the product and
void the warranty.
Surface Mount:
Handlebar Mount:
Suggested Sheet Metal Thickness: 0.059"(1.5mm)
0.83"
(21mm)
Screw (1/4 in)
Spring Washer
Flat Washer
Mounting Surface
- 4 -
Switch Panel
Select a mounting location that will not interfere or impede the operation and/or function
of any existing equipment. Securely mount the switch using the provided handlebar
clamp.
Handlebar Diameter Ø0.87"~Ø1.26" (Ø22mm~Ø32mm)

WIRING
To Slave Speaker +
ORANGE-BLK
To Slave Speaker -
YELLOW-BLK
Cable 1 (Power & Light Output)
- 5 -
Cable 2
(Switch, Mic &
Slave Unit Signal)
Ground
WHITE-BLK
Voice Signal
PURPLE
PTT
BLUE
Mic Set
(Optional)
IGN
WHITE
Car Ignition Key
Light Outupt #1
YELLOW
Light Output #2
ORANGE
Device #1
Device #2
(Max Output Amperage
@ 5A)
(Max Output Amperage
@ 5A)
POWER -GND
BLACK
POWER +VDC
RED
POWER +VDC
RED
Power Source
(Fuse Rating:
20 A @ 13.6VDC)
To Master Speaker -
YELLOW-BLK
To Master Speaker +
ORANGE-BLK
SAS32R-M
Master
SAS32R-S
Slave
(Optional)
Light Button
GREY
Siren Button
PINK
Air Horn Button
BROWN
Control Switch
POWER -GND
WHITE-BLK
POWER +VDC
GREEN

CONTROLLER FUNCTION
PA BROADCAST
Light Output
Siren Tone
Air Horn
1.At any moment, short press once to activate or inactivate all Light
Output #1 & #2 together.
2.While all light outputs are activated, press to activate only Light
Output #1.
3.While only Light Output #1 is activated, press again to deactivate
all Light Output.
NOTE: Siren will deactivate when Light Output #1 is deactivated.
PA Activation
Press “Push-to-Talk” button on the side of the Mic to activate
PA broadcasting. PA broadcasting will override all current
Siren Tone. Action will resume when PTT is released.
1.While Light Output #1 is activated,
■ quick press once to active the siren tone in Full Power (Day Mode).
■ long press once to active the siren tone in Low Power (Night Mode).
2.While siren is activated, press again to cycle through all available tones (if applicable).
3.To switch between Day / Night Mode, long press while the siren is activated.
4.To deactivate, quick double press while the siren is activated.
NOTE: Siren will deactivate when Light Output #1 is deactivated.
1.Press and hold for Air Horn tone.
2.Air Horn with override all current siren tone.
Mic Volume Adjustment Knob
(available on selected mic model only)
The knob located on the top right corner of the controller will
adjust mic volume (high or low). Turn clockwise for high
volume; turn anticlockwise for low volume.
- 6 -
Mic Volume
Adjustment Knob
PTT
PTT
Clip-on Mic
Handheld Mic
“ON →Output #1 & #2 →Output #1 → OFF ”

- 7 -
TONE GROUP PROGRAMMING
1. Turn off the system by disconnecting
the Car Ignition Switch (WHITE wire).
2. While holding on to “Light Output”
button (GREY wire) and “Air Horn”
button (BROWN wire), turn on the
system by connecting the Car Ignition
Switch (WHITE wire) and enter the
SETTING MODE.
3. While in SETTING MODE. speaker will play
long and short beep sound representing the
current Tone Group. To change Tone Group
press “Siren Tone” burron (PINK wire):
- once for next the Tone Group.
- quick 3 time for Tone Group #1.
(refer to Tone Group Chart)
Change Tone Group
4. Once in the desired Tone Group, save and exit
SETTING MODE by disconnecting the Car
Ignition Switch (WHITE wire).
Tone Group Chart
1
# BEEP SOUND
.
..
...
....
―
――
――.
――..
――...
―.
―..
―...
―....
2
3
4
5
6
7
8
9
10
11
12
13
COUNTRY TONE Hz
STANDARD
FRANCE
FRANCE
FRANCE
FRANCE
FRANCE
GERMANY
AUSTRIA
AUSTRIA
AUSTRIA
ITALY
ITALY
ITALY
GENDARMERIE
POLICE
AMBULANCE
POMPIERS
UMH
STADT
LAND
POLICE
AMBULANCE
FIRE BRIGADE
POLICE
AMBULANCE
AMBULANCE
STANDARD WAIL
YELP
2TONE
WAIL
YELP
2TONE
2TONE 435-735
759-1592
759-1592
759-1592
759-1592
450-600
435-580
420-516-420
435-488
435-651
432-576
362-483
430-575
523-392
392-523
466-622
392-660-392-660
392-660-392-660
2TONE
2TONE
2TONE
2TONE
2TONE
2TONE
2TONE
2TONE
2TONE
2TONE
2TONE
Car Ignition Key
― = Long Beep . = Short Beep