Cell2Tel C2T-XT2000 User manual

Bluetooth Cellular Gateway

INSTALLATION OPTIONS
1. With Cell Phone(s) only
OR
TELEPHONE
OUTLET
I I
I
I I
I
POWER SUPPLY
TELEPHONE CORD
2.With Home Line & Cell Phone(s)
NOTE:
*A hanging lid
a) To plug the telephone cord into the [TEL.L1NE] jack, move the hanging lid
to the left.
b) To download the new Bluetooth firmware, you have to first DISCONNECT
the telephone cord from the jack of [TEL.LINE], move the hanging lid to the
right, and then plug the USB cord into the USB jack. Once the new firmware
has been updated, disconnect the USB cord and complete step a.) again.
TELEPHONE
OUTLET OUTLET
I •
I
•I •
I
t .....
TELEPHONE CORD
1

STEP 1 Plug-in & Connect
Plug the PowerAdaptor from
wall outlet into
Cel12Tei
Plug USB line cord
from your
computer+--"
into Cel12Tei
*Hanging lid ........
Plug telephone service line
from wall outlet into Cell2Tei
Plug telephone cord from main
home telephone into Cell2Tei
2

STEP 2 Ready for Pairing
Select line [Cell Phone 1], or [Cell Phone 2] on Cell2Tei
Press and hold down
button for selected ~
line for about ..,.,.
4to 5 seconds until
amber button light
blinks quickly
~
Enable your Bluetooth function
on your cellular phone (refer to your
cellular phone's manual if necessary)
steps may differ by model
Typical Pairing
- Select "Hands Free"
- Select "Look For Devices"
- Select "Gateway 300"
- Select "Yes" and pair with Cell2Tei
- Enter pin code "0000"
- Press "OK"
Note:
Pin code 0000
3

STEP 3 Pair Cellular Phone to Cell2Tei
Amber light stops blinking and remains on when
cellular and selected Cell2Teiline are paired
successfully
~
YOUR
CONNECTED!
4

OUTLETS
Cell Phone line 1'-'-
Cell Phone line 2
Error correction
light indicator
POWER ADAPTER
CONNECTION
USB CONNECTION ......
TELEPHONE SERVICE -.'
LINE CONNECTION
(to wall outlet)
TELEPHONE CORD
CONNECTION
(to main home phone)
5
Power and
incoming ring
light indicator

NOTES
- Each cell phone line can only be paired to ONE
cell phone at a time.
- A cell phone line can be paired to a different cell
phone at any time by repeating the pairing
procedure.
- Previous pairing information is lost when pairing
is initiated for the same cell phone line.
- A paired cell phone line can be "unpaired" and
prepared for re-pairing by holding down the line
button until the amber light button blinks quickly.
- The pairing process can be aborted at any time
by pressing the cell phone line button. In this
case, the previous paired cell phone will be
disconnected.
6

CONTACT INFORMATION
•
CUSTOMER SERVICE & SUPPORT
Should you have any questions regarding
your Ce112Tel, please
visit us at www.ceI12telgateway.com
Made In China
Copyright@Cell2Tel Ltd.
Cel12Tei is a
registered Trademark of
Cell2Tei Ltd.
All rights reserved.
Cell2Tei Ltd. Los Angeles, CA. Hong Kong, China Cell2Tei C2T-XT2000

~
CELL2TEL
, ~

IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of fire, electric shock and/or injury to persons,
always follow these basic safety precautions when using your Cel12Tei
C2T-XT2000.
1. Read, understand, and follow all instructions.
2. Unplug this unit from the wall outlet before cleaning. Do not
use liquid or aerosol cleaners. If necessary, use a soft cloth
lightly moistened with a mild detergent solution.
3. Do not use this unit near a bathtub, kitchen sink, wash
bowl, laundry tub, swimm ing pool, a wet basement or anywhere
else there is water or liquid.
4. Do not place this unit on an unstable cart, stand or table.
A fall could cause serious damage to the phone.
5. Slots and openings in the cabinet at the back or bottom are
provided for ventilation to protect the unit from overheating.
These openings must not be blocked or covered. Do not place
this unit on a bed, sofa, rug or other similar surface. This
unit should never be placed near or over aradiator or heat
register. This unit should not be placed in abuilt-in
installation unless proper ventilation is provided.
6. Never push objects of any kind through slots in the phone. They
could touch dangerous voltage points or short out parts that
could result in a risk of fire or electric shock. Never spill liquid of
any kind on the unit.
7. Unplug this unit from the wall outlet and refer to aqualified service
representative in any of the following situations:
a. If liquid has been spilled into the unit.
b. If the unit has been exposed to rain or water.
c. If the unit does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions. Improper adjustment
of other controls may result in damage and will often require
extensive work by aqualified technician to restore the

unit to normal operation.
d. If the unit has been dropped or the case has been damaged.
e. If the unit exhibits adistinct change in performance.
8. Do not use the telephone to report agas leak in the vicinity of
the leak.
9. Avoid using atelephone (other than acordless type) during an
electrical storm. There may be aremote risk of electric shock
from lightning.
10. Never install jacks in awet location unless the jack is specifically
designed for wet locations.
11. Never touch uninsulated telephone wires or terminals unless the
telephone line has been disconnected at the network interface.
12. Use with caution when installing or modifying telephone lines.
13. To reduce the risk of electric shock, do not disassemble this
product, but take
it to aqualified serviceman when some service
or repair work
is required. Opening or removing covers may
expose you to dangerous voltages or other risks. Incorrect
reassembly can cause electric shock when the appliance
is
subsequently used.
14. Use only the power cord and batteries indicated in this manual.
Do not dispose of batteries
in fire. They may explode. Check
with local codes for possible special disposal instructions.
15. Plug the power adaptor to the socket-outlet that near the
equipment and shall be easily accessible.
16. The equipment is to be supplied from an identified USB
Port complying with the requirement of Limited Power
Source.
CAUTION: Power Adaptor should vertical mount
or floor mount position.
~ Use only with Class 2Power Source, 9V DC,
SOOmA

SAVE THESE INSTRUCTIONS
WARNING
To reduce the risk of fire or electric shock, do not expose this
appliance to rain or moisture.
CAUTION
RISKS OF ELECTRIC SHOCK- DO NOT OPEN!
To reduce the risk of electric shock, do not remove casing.
A A No user serviceable parts inside. Refer servicing to
qualified service personnel.
The light flash with arrowhead symbol, within an equilateral triangle,
is intended to alert user to the presence of dangerous voltage which
may cause electric shock to persons using it.
The exclamation point inside an equilateral triangle is intended to
alert user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
WARNING
This Product may contain chem icals listed in Proposition 65
(!!nP:/Iwww.oehha.ca.gov/~65IistlNewlist.html) that
may be known to cause cancer, birth defects or other reproductive
harm.

CONTENTS
INTRODUCTION .1
PACKAGE CONTENTS 1
SPECIFICATIONS "1
FEATURE HIGHLIGHTS 1
CONNECTIONS DIAGRAM 2
SETUP 3
Pairing Your Bluetooth Enabled Cell Phone(s) to Cell2Tei 4
Automatic Bluetooth Connection 5
Manual Bluetooth Connection 6
TESTING the SETUP 6
LINE STATUS & LIGHT INDICATORS 7
USING Cel12Tei 8
Placing a Call 8
Selecting a Line 9
Receiving aCall····································································································10
Force Call Connection 10
Speed Dialing 10
Voice Mail ·····················································11
Caller ID 11
Call Waiting 12
Voice Dialing 12
COMPUTER CONNECTIVITY... 13
TROUBLE SHOOTING .. 13
WARRANTY 19

INTRODUCTION
Congratulations on your purchase of the Cell2Tei C2T-XT2000
Cellular Bluetooth Gateway. In addition to your regular telephone
line you will now
be able to access up to 2Bluetooth enabled cell
phones from any standard telephone connected
to the Cell2Tei
C2T-XT2000 via your cell phone's Bluetooth connection.
Cell2Tei is designed to work with or without
telephone service (land line).
PACKAGE CONTENTS
The Cell2Tei gift box includes the following.
-Cel12Tei C2T-XT2000 Unit
9-Volt
DC Power Adapter
Quick Start Guide
Owner's Manual
Telephone Cord
USB Cord
SPECIFICATIONS
Bluetooth v2.0 compliant (Compatible wi Bluetooth v1.2)
Supports Headset and Handsfree Profiles
Operational range approximately
10 meters (30')
Input voltage 9V
DC
FEATURE HIGHLIGHTS
*Works with both home line (PSTN) and Bluetooth enabled cell
phone
*Pair and make Bluetooth wireless connection with 1or 2
Bluetooth cell phones
*True Multi-Line Operation: one home line (PSTN) via extension
telephone,
two wireless lines via two Bluetooth enabled cell phones
1

*Fully compatible with any brand of home telephone
*Direct access to home line by simply picking up the extension
telephone
* USB connection to download updates (firmware) for future cell
phone models
* Call Waiting through multi-line and multi-call
* Access cell phone voice mail, voice dialing and speed dialing*
* Force Call Connection*
*Error Installation/Connection tIx Indicator
*Individual LED Indicator for home line, Cell Phone Line 1 and Cell
Phone Line 2 with distinctive ring patterns
WARNJNG:
. IF the REDiIx error light is ON, the lines connected to the Cel12Tei
have NOT been connected properly. In this case, refer to page 5 for
the Cell2Tei Connections Diagram and check the connections.
CONNECTIONS DIAGRAM
CELL PHONE #2
LINE STATUS LIGHT
CELL PHONE #2 LINE BunON
ij II
C.IIPh~ 1
CELL PHONE #1
LINE STATUS LIGHT
POWER
INDICATOR ERROR LIGHT
CELL PHONE #1 LINE BunON
2

POWER TELEPHONE CORD
ADAPTER CONNECTION
CONNECTION USB L---_~-I---------...:....:~----J
CONNECTION TELEPHONE SERVICE LINE
* HANGING CONNECTION
LID
•
• •
WAl.lOUTlfT
seTUP
1. Plug a standard corded or cordless
telephone into the Cel12Tei [PHONE] jack I:l
using a regular telephone cord. u-~~.~ ~
2. IF a telephone service landline is used,
plug the telephone service line into the
Cell2Tei [TEL. LINE] jack using the cord
from the wall.
NOTE:
*A hanging lid
a)
To plug the telephone cord into the
[TEL. LINE] jack, move the hanging lid to the left.
b
)To download the new bluetooth firmware, you have to
first DISCONNECT the telephone cord from the
jack of
[TEL.LINE], move the hanging lid to the right,and then plug
USB cord into the USB jack. Once the
new firmware has been
updated, disconnect the
USB cord and complete step a) again.
3. Plug the connection from the supplied power adapter into the
Cell2Tei DC connection and plug end the pronged plug into
a wall power outlet.
4. To pair your Bluetooth cell phone refer to page 4 "Pair Your Bluetooth
Enabled Cell Phone( s) to Ce1l2Tel"
'l)HINT:
* Place your Cel12Tei &cell phone(s) where you have the best
cellular reception in your home or office.
* For best audio quality keep your paired cell phone(s) within
10' of your Cel12Tei
* Using a multi handset cordless phone gives you multiple
extensions.
* Certain cordless phones operate using the 2.4 GHz
frequence. Keep as much distance as possible between the
3

Cell2Tei and these types of cordless phones.
*Some wireless networks (Wi-Fi), such as 802.11 Jmay
interfere with Bluetooth
radio signals. Keep as much
distance as possible between this type of equipment, the
Cell2Tei and your cell phones.
PAIR YOUR Bluetooth ENABLED
CELL PHONE(S) to Cell2Tei
Your Cell2Tei can be paired (connected) up to two different cell phones,
one cell phone per Cel12Tei line. To pair aBluetooth cell phone to a
Cel12Tei
line, complete the following steps:
1. Press and hold one of the two cell phone line buttons on the
Cel12Tei until the amber status light flashes rapidly (Press & hold for
approximately 4seconds to start the status light to flash)
2. Put your cell phone in the mode where the cell phone searches for
Bluetooth devices. This mode should be found in your cell phone's
menu under 'Tools', 'Setup', 'BluetoothJ and/or 'Connections' menu. If
given the choice, search for 'Handsfree' devices and select "Look for
Devices". Your cell phone should then scan/search for Bluetooth
devices within range.
3. \f\Ihen the Cel12Tei is found, "Gateway301"will be displayed on your cell
phone's LCD. Accept this device. In order to accept, your cell phone
may ask you to do so by pressing any number of selections including
'select','bond','pair', 'yes', 'ok', etc.
4. Enter the pass code: '0000'
5. Once the pairing is complete, the selected cell phone line's amber
light button on the Cell2Tei will stop flashing quickly and remain solid.
Once paired, Cel12Tei should remember the cell phone. Your cell
phone will drop the connection when out of range and automatically
re-connect
when within range (approx. 30') of your Cel12Tei.
4

Cell Phone Line #1
9 HINT:
~
k@ .. ;J~-
Co LII:J 0 J~
)
Cell Phone Line #2
* Each cell phone line can only be paired to ONE cell
phone at a time.
*A cell phone line can be paired to adifferent cell phone
at any time by repeating the pairing procedure.
* Previous pairing information is lost when pairing is
initiated for the same cell phone line.
*A paired cell phone line can be "unpaired" and prepared
for re-pairing by holding down the line button until the
button flashes rapidly.
* The pairing process can be aborted at any time by
pressing the cell phone line button. In this case, the
previous paired cell phone will be disconnected.
Automatic Bluetooth Connection
Once a cell phone has been paired to a cell phone line, the Cell2Tei will
automatically try to connect wirelessly. When the cell phone goes out
of range, the corresponded cell phone line status light will flash slowly
to indicate it is not connected and is searching for the cell phone.
When the cell phone comes into range of the Cel12Tei connection
should occur automatically and the line status light will turn solid
amber to indicate an active connection.
If you are on a cell call and walk into range, the Cell2Tei and cell phone
will automatically connect. In this case, you will be able to continue
your call without interruption.
If a cell phone line status light is not flashing, and you wish to place
the cell phone line into automatic connection mode, simply press its
corresponded cell phone line button once.
5

Manual Bluetooth Connection
You may not want live cell calls to be transferred automatically or you
may want to force your cell phone to disconnect from the Cel12Tei .
V\lhen a cell phone line is connected (amber line status light remains
on), press the said cell phone line button to disconnect that line. In this
case, the amber light will turn off once disconnected and audio will be
transferred to the cell phone so you can continue your call on the cell
phone.
VVhen a cell phone line is not connected and not searching (amber
light remains off) pressing the cell phone line button will put the line
into searching mode (amber light flashes slowly). If the cell phone
has been previously paired and is within reception range, the cell
phone will connect with the Cell2Tei and the amber light will remain
solid.
NOTE:
* Some cell phones will prompt you when you are within range
of the Ce1l2Tel. You can decide to transfer the call to the
Cell2Tei at that time.
TESTING THE SETUP
After connecting one or more telephones to the Cell2Tei , the setup
test feature can be used to ensure proper connections.
1. Ensure the green @ power light is ON and the red itx error light is
NorON
6

2. Simultaneously, press and hold Cell Phone 1 and Cell Phone 2
Line Buttons for approximately 4 seconds: all telephones
connected to Cell2Tei should start ringing.
i HINT:
* If an extension telephone does not ring, check that the phone is
properly powered and that all cables are properly connected.
NOTE: Cel12Tei should support ALL telephones, including older
analog telephones with DTMF dialing
LINE STATUS & LIGHT INDICATORS
Green Solid @
Indicates the unit is powered and operating normally.
GREEN RED
Green Flashing
Indicates there is an incoming call on the telephone
service line (Iandline)
Red ON itx
AMBER
Indicates the Cell2Tei connections have not been
connected properly. Immediately re-check line
connections until the red light turns off and the green light remains
on.
Amber Solid
Indicates the selected cell phone line is connected to cell phone
7