Celsius CHL425W User manual

For models: CHL425W
Heat/Light/Vent –4 Light
with LED Centre Bulb
OPERATING INSTRUCTIONS

HEAT/LIGHT/VENT INSTRUCTIONS
Thank you for choosing CELSIUS. Your CELSIUS Bathroom Heat/Light/Vent has been
designed and manufactured to high standards of engineering. With proper use and care,
as described in this leaflet, you can expect years of service. Please read these
instructions carefully.
GENERAL CARE AND SAFETY GUIDE
Please read all instructions carefully before using your bathroom heater and
keep them for future reference.
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience or knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their
safety
Children should be supervised to ensure they do not play with the appliance
Use only the voltage specified on the rating plate of the appliance
Do not cover or restrict airflow as the appliance may overheat and become a fire risk
Do not cover heat lamps, or inlet of airflow by placing these areas of the appliance against any
surface
Do not mount appliance close to any heat source
Do not operate in areas where petrol, paint or other flammable liquids are used or stored
Do not use the appliance to dry clothes
Do not insert or allow foreign objects to enter any point of the appliance, as this may cause an
electric shock, fire or damage to the appliance
Do not immerse in liquid or allow liquid to run into the interior of the appliance, as this could
create an electrical shock hazard
Do not operate after the appliance malfunctions, has been dropped/damaged in any manner.
Do not operate the appliance with wet hands
Use this appliance only as described in this manual. Any other use is not recommended by the
manufacturer may cause fire, electric shock or injury
Do not use this appliance in a window as rain may cause electric shock
Do not connect the appliance to the electrical supply until completely assembled
This appliance is intended for household use only and not for commercial or industrial use

HEAT/LIGHT/VENT INSTRUCTIONS
GENERAL NOTES
This Celsius product is designed only to be used as a fixed Heat/Light/Vent product, installed
into the ceiling. If the product is installed or used for any other purpose the warranty will be void.
Installation of this product must be completed by a registered electrician.
Handle product with care, remove the bulbs during installation.
The unit must be located and installed in accordance with the AS/NZS 3000:2007 and any local
regulation information for mounting in damp areas (please consult your local electrician for
information).
A means of disconnection must be incorporated in the fixed wiring in accordance with the wiring
rules.
The unit can be installed in any room that requires direct radiant heating and circulated air flow
such as bathrooms, ensuites, laundries, etc.
The unit must be installed in flat ceilings with a minimum height of 2 metres from the floor.
Do not install the unit directly above shower or bath recesses or enclosures.
The unit must not be installed in a position where water may splash onto the heat lamps.
At least 220mm height clearance in the ceiling cavity is required to ensure sufficient ventilation
for moisture to disperse.
Joists, beams and rafters shall not be cut or notched to install the appliance.
The unit must also be installed at least 400mm away from the walls.
The appliance shall under no circumstances, be covered with insulating material or similar
material.
For maximum efficiency to remove steam and odours, there must be an adequate air flow within
the room. To obtain maximum air flow ensure there is a gap under doors or open windows
slightly. A good test for this is that the fan should not change speed (or sound) when you close
or open the bathroom door.
220-240V 50Hz electrical supply is required. The unit can be connected to a lighting or power
circuit if loading permits. All electrical work must be carried out by a registered electrician in
accordance with AS/NZS 3000:2007 (please consult your local electrician for information). A
three gang switch is included to so the user can independently switch the Ventilation, Heat and
Light on and off. This needs to be installed in a position where it cannot be reached from the
bath or shower.
Heat lamps and light bulbs supplied with the unit are test bulbs only, these are not covered

HEAT/LIGHT/VENT INSTRUCTIONS
USER INSTRUCTIONS
Your Heat/Light/Fan unit comes with a wall switch included. Once wired correctly by your
electrician you need to simply follow the below instructions.
To turn the centre light bulb on press the “LIGHT” switch down (and up to turn off).
To turn the ventilation fan on press the “FAN” switch down (and up to turn off).
To turn 2 heat lamps on press one of the “HEAT” switches down (and up to turn off).
To turn all 4 heat lamps on press both of the “HEAT” switches down (and up to turn off).
Air Flow Requirements:
For maximum efficiency to remove steam and odours, there must be an adequate air flow within
the room. To obtain maximum air flow ensure there is a gap under doors or open windows
slightly. A good test for this is that the fan should not change speed (or sound) when you close
or open the bathroom door.
Important Note:
Always turn the fan on when using the heat lamps to minimise any undue
heat build up in the unit.

INSTALLATION INSTRUCTIONS
1.The unit may be mounted either between joists using the inbuilt clip fasteners or against a
joist using a screw through the flange plate. The approximate cut-out size of the unit is 295 x
295mm.Please note this is only an approximate measurement and any installation would
require a measurement against the physical product to ensure the best fit. Mark the
ceiling with a pencil showing the area of ceiling to be cut.
IMPORTANT NOTE: Celsius takes no responsibility for those instances where the physical
product is not measured first before the hole is cut in the ceiling.
2.Before commencing cutting ensure that the area behind the intended location is clear of all
cables, pipes and joists. Once clear, cut out the section along the previously marked lines.
3.Remove the lamps from the housing by unscrewing them anticlockwise. Then remove the
decorative fascia from the housing by removing the spring clips that hold it in place.
4.Insert the unit into the hole being sure to pull the side springs inward so that the body can
pass through the hole without damaging the plaster. Ensure that the unit is held securely in
place by clips. It is essential that additional screws (not supplied) are used to aid holding the
unit in the ceiling. Screw holes are provided in the flange for this purpose. 2 strips of timber
(one on each side) should be placed behind the holes inside the ceiling to give the screws
something to anchor to and to provide some reinforcing. Do not secure the unit at this time.
5.Remove the unit from the ceiling and connect the wiring to the terminal block as per the wiring
diagram. This terminal block is on one corner of the back of the unit.
6.Insert the unit into the hole and secure as detailed in point 4 above.
7.1x white and 1x silver fascia are included with this product. Choose only one of these fascia
colours to install. Hold the fascia against the body of the appliance and the ceiling, then attach
the securing spring clips to hold the fascia in place.
8.Now screw in the 275W heat lamps provided into the lamp holder through the holes provided
in the fascia. The globes should be screwed in firmly to ensure a good electrical contact but
don’t over tighten. Fit the small centre light bulb in the same way ensuring that it is positioned
centrally.
IMPORTANT NOTE: Over tightening of heat lamps or light bulbs may result in damages to the
lamp holders or lamps, take care when removing and replacing heat lamps/bulbs
HEAT/LIGHT/VENT INSTRUCTIONS

ELECTRICAL INSTALLATION
IMPORTANT NOTE: All electrical work and installation of this product must be
performed by a registered electrician in accordance with AS/NZS 3000:2007.
Note: The unit is fitted with a safety thermal switch which will
activate the fan to cool the unit if the heat generated by the heat
lamps exceeds a certain level.
It is imperative that this feature is enabled.
Ensure power to the circuit to be used has been isolated at the power board
before carrying out any electrical work.
Technical Specifications:
220-240VAC 50/60Hz
1131W (Max)
WIRING DIAGRAM
HEAT/LIGHT/VENT INSTRUCTIONS

SPARE PARTS
If for any reason you require spare parts, please contact Celsius customer services in the first
instance
Replacement Heat lamps and light bulbs can be purchased from your local retailer. Celsius
recommends the use of Elite heat lamps and light bulbs (please note these items are not
covered under warranty)
HEAT/LIGHT/VENT INSTRUCTIONS
SUPPORT AND TECHNICAL ADVICE
Celsius –New Zealand
Monday –Friday 8am-5pm
Phone [phone]
Phone [phone]
[e-mail]
Celsius –Australia
Monday –Friday 8am-5pm
Phone [phone]
Phone [phone]
[e-mail]

Thank you for purchasing this Celsius product. Your product is warranted against faults and manufacture when used in
normal domestic use for a period of one year. In non-domestic use Celsius limits the voluntary warranty to three
months.
Celsius undertake to repair or replace this product at no charge if found to be defective due to a manufacturing fault during
the warranty period.
This warranty excludes damage caused by misuse, neglect, shipping accident, incorrect installation, or work carried out by
anyone other than a qualified electrical service technician.
PLEASE KEEP YOUR RECEIPT AS THIS WILL HELP VERIFY YOUR WARRANTY.
The benefits given to you by this warranty are in addition to other rights and remedies available to you under law in
relation to the goods or services to which this warranty relates.
In Australia, our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are
entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
In New Zealand this warranty is additional to the conditions and guarantees of the Consumers Guarantee Act (1993).
One Year Warranty
Celsius One Year Warranty (IMPORTANT: Please complete and retain this warranty card)
Name
Address
Place Of Purchase Date Of Purchase
Name Of Product Model Number
Attach a copy of the purchase receipt to this warranty card
Celsius –New Zealand
PO Box 100-707
N.S.M.C
Auckland, 0745
Phone [phone]
Phone [phone]
www.celsius.co.nz
Celsius –Australia
PO Box 574
South Morang
Victoria, 3752
Phone [phone]
Phone [phone]
www.celsiusforhome.com.au
Due to continual design improvements, the product illustrated in this User Manual may differ slightly from the actual product.