Cenocco CC-9098 User manual

BLACKHEAD REMOVER
CC-9098
USER MANUAL
Thank you for your recent purchase of our product.
Read instructions carefully before using the product.
Results may vary depending proper pore preparation.
Blackhead Remover Vacuum suction device to quickly remove
the outer epidermis and unwanted skin grease, residual dirt
buildup, and moderate removal of dead skin keratin.
1. Find a cleanser that is best suited to your skin type. A
creamy wash works well for dry or sensitive skin. Consider a
gel formula for combination or oily skin.
2.Wetyour face with warm (not cold or hot) water.
3.Apply the cleanser in gentle circular motions. Massage in
your skin for about one minute without scrubbing.
4.Rinse thoroughly with warm water. You can also gently wipe
away the cleanser with a warm washcloth for an extra clean
feeling.
5.Soak a cloth in warm to hot {not being but hot enough to
still be able to touch) water and wring out the excess water.
6.Hold cloth over the face to steam out pores until cloth cools
down. Repeat 3x-4x's.
7.Pat (do not rub) your face dry.
Name
Blackhead Remover
Battery capacity
500 mAh
Work Time
≥120 minutes
Charging Time
about 2 hours
Standard
GB4706.59-2008
Rate Voltage
5V
Rate Power
1.6W
Rate Current
450 mA
Product is best used after proper face prep instructions.
1. Choose suction tip to desired needs.
2.Light press the power button to start, and then press the
selection of gear, a total of three gears.
3.Turn on default is medium gear (neutral skin).
then press the power button to switch to high gear
(dry skin): press power button again to switch to low gear
(oily skin). A total of 3 modes to choose from depending on
skin type (low, medium, and high). Spot test on arm or hand
to test strength prior to applying on face.
4.Hold down power button for 3 sec to shut down device.
5.Electricity indicator flashes when charging, and stays on
when full.
(1) Charging indicator
(2) Gear indicator
(3) ON/Off key
(4) USB Charger
Note: On/Off Key - Press the key to turn on, then press to
choose the different gear. Hold down to shutdown
PRODUCT INTRODUCTION
FACE PREP
PRODUCT PARAMETERS
INSTRUCTIONS
FUNCTIONS

1. Clean and dry facial skin.
2.Replace the working sucker with microcrystalline or large
circular hole:
A Place the working suction head in the mandibular region
and move from the bottom to the top.
B. Place the work suction heads in the cheek area and move
from inside to outside.
C. Place the working suction head in the forehead area and
move from the middle to both sides.
D. Place the working suction head in T area and move from
bottom to top.
1. Clean and dry facial skin:
2.Choose and apply desired suction tip.
3.For the removal of blackheads and acne. slide slowly in
single horizontal direction.
4.Do not suck on the same spot for more than 3 sec.
1.Clean and dry facial skin.
2. Replace the elliptical working suction head.
3. Place the working suction head at the corners of the eye.
nose. lip, etc. and move up quickly. Pull and pull repeatedly.
Act on the underlying layer of skin. increase skin Elasticity,
wake up vitality. prevent wrinkles.
Small round hole working sucker
Small suction, used to suck blackheads.
Thin tender and sensitive skin If the
suction is not too strong, use a small
suction head.
Medium round hole working sucker
High suction. used to suck blackheads.
acne. Those with excessive fat, do not use
it in one place for a long time.
Large round hole working sucker
High suction, used to suck black head,
tight V face. When smoking blackheads to
move slowly back on the skin. do not
spend too long in one place. Use in part;
when molding V-face. use pull-up from
bottom to top Maneuver, move slowly
from chin up.
Elliptical hole working sucker
It is mainly used for removing fine lines.
It needs to be quickly pulled out after
absorbing the skin. Repeats many times,
may play the promotion skin blood
circulation, increases Skin elasticity.
Microcrystalline working sucker
Fine crystals can gently remove aging cutin
and make skin tender. Delicate and
slippery.
•This product has no waterproof function. Please
•wipe the water or other liquids on your hands before use.
Dry to prevent water or other liquids from entering the
fuselage. thereby damaging the fuselage.
•Do not use abrasive plaster or other cutin products
before and after use.
•The function of dermabrasion and exfoliation. It is
recommended that dry skin be used once a week. oily or
oily. Neutral skin can be used twice a week.
•No more than 5 minutes for each use. It depends on the
skin condition.
•Please do not press the working suction head hard on
your skin, because the instrument will produce. Strong
pulling force.
•Do not continue to use in the same place. otherwise, it
may cause skin redness, Purple. If this happens, please
suspend use.
•After nursing, due to stimulating the internal circulation
of the skin or skin redness. It belongs to the normal
phenomenon and will fade out automatically about 30
minutes after use.
•This product is not suitable for cosmetic or skin cosmetic
surgery sites; Not suggested for persons with physical.
sensory or mental disabilities or lack of experience and
knowledge. Use cautiously for children: pregnant women
and patients with heart disease.
•Long periods of suction without movement could lead to
erythema’s/hematomas. Use with care.
DERMABRASION AND EXFOLIATION
CLEAN PORES AND DIRT
REDUCE FINE LINES
INTRODUCTION OF WORKING SUCKER
ATTENTIONS