Central Pneumatic 90193 User manual

AIR MINI HAND NAILER
ASSEMBLY and OPERATING
INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit ourWeb site at http://www.harborfreight.com
For technical questions and replacement parts,please call 1-800-444-3353
Model 90193
®
®
Copyright c 2003 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.

Page 2
SKU 90193
Specifications
Save This Manual
You will need the manual for the safety warnings and precautions, assembly instructions,
operating and maintenance procedures, parts list and diagram. Keep your invoice with this
manual. Write the invoice number on the inside of the front cover. Keep the manual and
invoice in a safe and dry place for future reference.
Safety Warnings and Precautions
WARNING: When using tool, basic safety precautions should always be followed to
reduce the risk of personal injury and damage to equipment.
Read all instructions before using this tool!
1. Keep work area clean. Cluttered areas invite injuries.
2. Observe work area conditions. Do not use machines or power tools in damp or wet
locations. Don’t expose to rain. Keep work area well lighted. Do not use electrically
powered tools in the presence of flammable gases or liquids.
3. Keep children away. Children must never be allowed in the work area. Do not let
them handle machines, tools, extension cords, or air hoses.
4. Store idle equipment. When not in use, tools must be stored in a dry location to
inhibit rust. Always lock up tools and keep out of reach of children.
5. Use the right tool for the job. Do not attempt to force a small tool or
attachment to do the work of a larger industrial tool. There are certain applications for
which this tool was designed. It will do the job better and more safely at the rate for
which it was intended. Do not modify this tool and do not use this tool for a purpose for
which it was not intended.
6. Dress properly. Do not wear loose clothing or jewelry as they can be caught in
moving parts. Protective, electrically non-conductive clothes and non-skid footwear
are recommended when working. Wear restrictive hair covering to contain long hair.
7. Use eye and ear protection. Always wear ANSI approved impact safety goggles.
Wear a full face shield if you are producing metal filings or wood chips.Wear an ANSI
approved dust mask or respirator when working around metal, wood, and chemical
dusts and mists.
Air Inlet 1/4” NPT - 18 NPT
Recommended Air Pressure 60-90 PSI
Maximum Air Pressure 90 PSI
Nail Type and Size 8D (9/32”)
Air Consumption 1-2 CFM
Overall Dimensions 2-3/4” L x 2-1/4” W x 3-1/2” H

Page 3
SKU 90193
8. Do not overreach. Keep proper footing and balance at all times. Do not reach over
or across running machines or air hoses.
9. Maintain tools with care. Keep tools clean for better and safer performance. Follow
instructions for lubricating and changing accessories. Inspect tool cords and air hoses
periodically and, if damaged, have them repaired by an authorized technician.The
handles must be kept clean, dry, and free from oil and grease at all times.
10. Disconnect air supply. Disconnect air hose when not in use.
11. Remove adjusting keys and wrenches. Check that keys and adjusting wrenches
are removed from the tool or machine work surface before plugging it in.
12. Stay alert. Watch what you are doing, use common sense. Do not operate any tool
when you are tired.
13. Check for damaged parts. Before using any tool, any part that appears damaged
should be carefully checked to determine that it will operate properly and perform its
intended function. Check for alignment and binding of moving parts; any broken parts
or mounting fixtures; and any other condition that may affect proper operation. Any
part that is damaged should be properly repaired or replaced by a qualified technician.
14. Guard against electric shock. Prevent body contact with grounded surfaces such as
pipes, radiators, ranges, and refrigerator enclosures.
15. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use accessories
intended for use with this tool. Approved accessories are available from Harbor
Freight Tools.
16. Do not operate tool is under the influence of alcohol or drugs. Read warning
labels if taking prescription medicine to determine if your judgement or reflexes are
impaired while taking drugs. If there is any doubt, do not operate the .
17. Use proper size and type extension cord. If an extension cord is required for the air
compressor, it must be of the proper size and type to supply the correct current to the
tool without heating up. Otherwise, the extension cord could melt and catch fire, or
cause electrical damage to the tool. Check your compressor’s manual for the
appropriate size cord.
18. Maintenance. For your safety, maintenance should be performed regularly by a
qualified technician.
19. Compressed air only. Never use combustible gases as a power source.
Note: Performance of the compressor (if powered by line voltage) may vary depending
on variations in local line voltage. Extension cord usage may also affect tool perfor-
mance.
Warning:The warnings,cautions,and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be under-
stood by the operator that common sense and caution are factors which cannot be
built into this product, but must be supplied by the operator.

Page 4
SKU 90193
Operation
For best service you should incorporate an oiler, regulator, and inline filter, as shown in the
diagram above. Hoses, couplers, oilers, regulators, and filters are all available at Harbor
Freight Tools.
1. You will need to prepare a 1/4”air connector (sold separately) to connect to the Air Inlet (20)
on the Nailer.First, wrap the 1/4”air connector (not included) with pipe thread seal tape before
threading it into the Air Inlet (20). Connect the 3/8” ID Air Source Hose to the air connector.
Note: If you are not using an automatic oiler system, before operation, add a few drops of
Pneumatic Tool Oil to the airline connection. Add a few drops more after each hour of con-
tinual use.
2. Set the air pressure on your compressor to 60-90 PSI. Do not exceed the recommended
air pressure of 90 PSI.
3. Check the air connection for leaks.
Unpacking
When unpacking, check to make sure the parts listed on page 6 are included. If any parts
are missing or broken, please call Harbor Freight Tools at the number on the cover of this
manual as soon as possible.
Mini Nailer
1/4” - 18 NPT
REV 11/03

Page 5
SKU 90193
Operation (continued)
Warning! Do not load a nail into the Nailer until you are ready to work.
Caution: Do not point the Nailer toward any person, pet, or toward yourself.
Immediately after finishing work, disconnect the Nailer from the air source.
Caution: After it is disconnected, the Nailer may still hold enough residual air charge
to fire a nail. With the Guide Box pressed against a solid surface, press down on the
top of the Nailer several times to expel any residual air charge.
4. Holding an 8D, 9/32” nail by the stem (not the tip), insert the head of the nail into the
Guide Box (#18), and grip your palm over the top of the Nailer. See FIGURE 1.
5. Position the nail on the workpiece and press the nail into the workpiece 2 to 6 times, or until
the nail is completely nailed in.
6. When you are finished nailing, immediately disconnect the air hose.
Maintenance
1. Wipe down the Nailer with a lint free cloth.
2. Make sure the Guide Box (#18) and the Air Inlet are free from any dirt or debris.
Grip palm over top.
Guide Box (#18)
Air Inlet on back side (not shown)
FIGURE 1
Caution: Do not point the Nailer toward any person, pet, or toward yourself.
Immediately after finishing work, disconnect the Nailer from the air source.

Page 6
SKU 90193
NOTE: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
PLEASE READTHE FOLLOWING CAREFULLY
THEMANUFACTURER AND/ORDISTRIBUTOR HAS PROVIDEDTHEPARTSDIAGRAMINTHIS
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBU-
TOR MAKES ANYREPRESENTATION ORWARRANTY OF ANYKINDTOTHE BUYERTHAT HE
OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER
AND/ORDISTRIBUTOREXPRESSLYSTATESTHATALLREPAIRSANDPARTSREPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSEDTECHNICIANS AND NOT BYTHE
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER
REPAIRS TOTHE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTSTHERETO.
Parts List
Part No. Description Qty.
1 Body 1
2 Damping Rubber 1
3 Piston Rod 1
4 Piston 1
5 O-Ring 1
6 O-Ring 1
7 Cylinder 1
8 O-Ring 2
9 Rubber Ring 1
10 Valve 1
11 O-Ring 2
12 Gasket 1
13 Valve Packing 1
14 Cover 1
15 Spring Washer 2
16 Spring 1
17 Guide Bushing 1
18 Guide Box 1
19 Screw 4
20 Air Inlet 1
REV 11/03

Page 7
SKU 90193
Assembly Drawing
REV 11/03