Central Pneumatic 42528 Parts list manual

18 Gauge
Air Brad Nailer
Model 42528
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit ourWeb site at http://www.harborfreight.com
Copyright©2000, 2004by Harbor FreightTools®. Allrights reserved. No
portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor FreightTools.
For technical questions and replacement parts, please call 1-800-444-3353
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
ASSEMBLY AND OPERATION INSTRUCTIONS

SKU 42528 Page 2For technical questions, please call 1-800-444-3353.
SPECIFICATIONS #42528 AIR BRAD NAILER
Save This Manual
You will need the manual for the safety warnings and precautions, assembly instruc-
tions, operating and maintenance procedures, parts list and diagram. Keep your invoice with
this manual. Write the invoice number on the inside of the front cover. Keep the manual and
invoice in a safe and dry place for future reference.
Safety Warnings and Precautions
WARNING: When using tool, basic safety precautions should always be
followed to reduce the risk of personal injury and damage to equipment.
Read all instructions before using this tool!
1. Keep work area clean. Cluttered areas invite injuries.
2. Observe work area conditions. Do not use machines or power tools in damp or wet
locations. Donotexposetorain. Keep workarea welllit. Do notuse electricallypowered
tools in the presence of flammable gases or liquids.
3. Keep children away. Children must never be allowed in the work area. Do not let them
handle machines, tools, extension cords, or air hoses.
4. Store idle equipment. When not in use, tools must be stored in a dry location to inhibit
rust. Always lock up tools and keep out of reach of children.
5. Use the right tool for the job. Do not attempt to force a small tool or attachment to do
the work of a larger industrial tool. There are certain applications for which this tool was
designed. It will do the job better and more safely at the rate for which it was intended.
Donot modifythis tool anddo notusethis toolfor a purposefor whichit was notintended.
6. Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving
parts. Protective, electrically non-conductive clothes and non-skid footwear are
recommended when working. Wear restrictive hair covering to contain long hair.
:eziStelnIriA
1
/
4
)elameF(TPN” :erusserPgnitarepO isp59ot55
:sdarB :epyT ).aG81(knahS"240.-930. daeHmuideM :yticapaCenizagaM sdarb001
:reggirT epyTtcatnoC
:htgneL
3
/
8
-1ot”
3
/
61
” :snoisnemiDllarevO -01
1
/
4
-7xW”2xL”
3
/
8
H”
:elpmaxE 50233UKS :thgieWteN .sbL02.2
FEATURES OF THIS AIR BRAD NAILER
1. This lightweight yet powerful air nailer will make short work of most nailing jobs.
2. 1/4” NPT air inlet size accepts most often used shop size air hose adapters.
3. Safety trigger will not discharge unless the nailer is in contact with a surface.
4. 100 brad magazine capacity reduces down time for reloading.
5. Wide range of brad sizes makes this the right nailer for most jobs.
6. Sturdy die-cast aluminum and steel construction assures long service life.

SKU 42528 Page 3For technical questions, please call 1-800-444-3353.
7. Do not overreach. Keep proper footing and balance at all times. Do not reach over or
across running machines or air hoses.
8. Useeye and ear protection. Alwayswear ANSIapprovedimpact safetygoggles
and appropriate hearing protection. Wear a full face shield if you are producing
metal filings or wood chips. Wear an ANSI approved dust mask or respirator
whenworking around metal, wood,and chemical dustsandmists. Other people
in the work area must also wear ANSI approved impact safety goggles.
9. Maintain tools with care. Keep tools clean for better and safer performance. Follow
instructions for lubricating and changing accessories. Inspect tool cords and air hoses
periodically and,if damaged,havethem repairedbyanauthorizedtechnician.Thehandle
must be kept clean, dry, and free from oil and grease at all times. Do not operate a tool if
any portion of the tool’s operating controls are inoperable, disconnected, altered or not
working properly.
10. Disconnect Air Hose and release any built-up air pressure. Neverservicethe Nailer,
clear jams, or disassemble with the air hose attached. Always release any built-up air
even after disconnecting hose. Disconnect the Nailer when not in use.
11. Remove adjusting keys and wrenches. Check that keys and adjusting wrenches are
removed from the tool or machine work surface before attaching to an air source.
12. Avoid unintentional starting. Be sure the trigger is in the Off position when not in use
and before plugging in.Do not carry any tool with your finger on the trigger, whether it is
attachedto anair source ornot. Do notpoint thetooltowards yourselfor anyonewhether
it contains fasteners or not.
13. Stay alert. Watchwhat youaredoing, use commonsense.Donotoperateanytool when
you are tired.
14. Check for damaged parts. Beforeusinganytool, anypartthatappearsdamaged should
be carefully checked to determine that it will operate properly and perform its intended
function.Check for alignment and binding of moving parts;any broken parts or mounting
fixtures;and anyotherconditionthat mayaffectproperoperation.Anypartthat isdamaged
should be properly repaired or replaced by a qualified technician. Do not use the tool if
the trigger does not operate properly.
15. Guard against electric shock. Prevent body contact with grounded surfaces such as
pipes, radiators, ranges, and refrigerator enclosures.
16. Replacement parts and accessories. This product is to be repaired and serviced only
by a qualifiedtechnician. Whenthis product isserviced, only identical replacementparts
should be used. Use of any other parts will void the warranty. Only use accessories
intended for use with this tool. Approved accessories are available from Harbor Freight
Tools.
17. Do not operate tool if under the influence of alcohol or drugs. Read warning labels
if taking prescription medicine to determine if your judgement or reflexes are impaired
while taking drugs. If there is any doubt, do not operate the tool.
18. Use proper size and type extension cord.If an extensioncordis required, itmust be of
the proper size and type to supply the correct current to the compressor without heating

SKU 42528 Page 4For technical questions, please call 1-800-444-3353.
up.Otherwise, the extension cord could melt and catch fire, or cause electrical damage
to the tool. Check your air compressor’s manual for the appropriate size cord. It is also
possible that the use of an extension cord may cause your circuit breaker to trip or your
panel fuse to break. If this happens, either use the compressor without an extension
cord or find a larger amperage circuit to use.
19. Maintenance. Themaintenanceoutlinedinthemaintenancesection shouldbeperformed
regularly. For your safety, this product should be serviced or repaired regularly only by a
qualified technician.
20. Compressed air only. Never use combustible gas as a power source.
21. Do not load nails with the trigger or safety depressed. Unintentional firing
may occur. Do not load nails when the air hose is connected to the tool. Always
assume that the tool contains fasteners.
22. Disconnect air supply before loading Nailer. Before reloading (or making any
adjustments to) the Nailer make sure that the compressed air is disconnected.
23. Fire fasteners into an appropriate work surface only. Donotattempt to fire fasteners
intosurfaces too hardto penetrate. Do notdrivefasteners on topof other fasteners,or at
too steep of an angle. Fasteners can ricochet causing personal injury. Never fire the
Nailer into the air, or point it toward yourself or another person. Always wear ANSI
approved safety goggles during use, maintenance, and reloading.
24. Do not fire fasteners too close to the edge of a workpiece. They may split the
workpiece and fly free, causing personal injury.
25. Take caution as some woods contain preservatives such as copper chromium
arsenate (CCA) which can be toxic. When stapling or nailing these materials extra
care should be taken to avoid inhalation and minimize skin contact.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities, contain chemicals known [to the State of California] to
cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and cement or other masonry products
• Arsenic and chromium from chemically treated lumber
(California Health & Safety Code 25249.5, et seq. )
26. Stay within air pressure capacity.Never operate the Nailer above 95 PSI.
27. Hold tool away from head and body. During operationtheNailer maykickbackcausing
injury.
28. Transport Nailer safely. Always disconnect air supply when moving the tool in the
workplace. Carry the tool by the handle and avoid contact with the trigger.
Note: Performance of the compressor (if powered by line voltage) may vary depending on
variations in local line voltage. Extension cord usage may also affect tool performance.

SKU 42528 Page 5For technical questions, please call 1-800-444-3353.
Warning:The warnings,cautions,and instructions discussed in this instruction manual
cannotcoverall possible conditions and situationsthat mayoccur.Itmust beunderstood
by the operator that common sense and caution are factors which cannot be built into
this product, but must be supplied by the operator.
Unpacking
When unpacking, check to make sure the parts listed on page 9 are
included.If any parts are missing or broken, please call Harbor Freight Tools at
the number on the cover of this manual as soon as possible.
INCLUDED ACCESSORIES
3mm Hex Wrench Tool Oil
4mm Hex Wrench Assorted O-rings*
*NOTE: Although spare assorted O-rings are included,
these parts are for installation by a qualified technician only.
Operation
For best service,youshould incorporateanoiler, regulator,and inline filter,asshown in
the diagram below. Hoses, couplers, oilers, regulators, and filters are all available at Harbor
Freight Tools.
Note: To connect this tool, we recommend a quick coupler/adapter (not included). Coupler/
adaptersare availableatHarborFreightTools.Forsmoother operation,put3-5 drops of
pneumatic tool oil in the Air Plug (A-04) before each use.
Nailer
Testing the Contact SafetyTrip Mechanism
Warning: Even though the nailer should be empty during this procedure,ALWAYS point
the nailer at a piece of scrap wood when testing.
1. Make sure the tool is disconnected from the power supply.
2. Completely empty the magazine of nails.
3. The Nailer should not fire if the nose is not depressed against the workpiece.
4. Check that the Trigger (A-26) and the Nose Piece (3-11) move freely, without sticking -
see Figure 1 , next page.
5. Connect the air supply to the tool at the Air Plug (A-04) set at the recommended 55-95
PSI, and not to go over the maximum 95 PSI.

SKU 42528 Page 6For technical questions, please call 1-800-444-3353.
6. Test the tool by depressing the Nose
Piece (3-11) against the workpiece
without pulling the Trigger (A-26). The
tool must not cycle (fire). If it cycles
(fires),stop immediatelyandhavethetool
repairedby aqualified service technician.
7. Holdthe toolawayor offof theworkpiece.
The Nose Piece (3-11) of the tool should
returntoitsoriginalposition. Squeeze the
Trigger (A-26). The tool must not cycle
(fire). Ifit cycles (fires), stopimmediately
and have the tool repaired by a qualified
service technician.
8. Depress the Nose Piece (3-11) against
theworkpiece andsqueezetheTrigger(A-
26). Thetoolmustcycle(fire)onceonly.
Release the trigger and squeeze it again.
The tool must cycle (fire) again once.
With the Trigger held, carefully lift the
nailer and press it against the workpiece again. The tool must cycle (fire) again once.
Ifit failsto cycle (fire)or fires repeatedly,haveit repairedbya qualified servicetechnician.
LoadingBradNails
ALWAYS WEAR ANSI APPROVED IMPACT SAFETY GOGGLES WHEN
RELOADING OR DOING ANY OTHER MAINTENANCE ON THIS TOOL. Other
people in the work area must also wear ANSI approved impact safety goggles.
Warning! Make sure the Nailer is not attached to the air hose whenever loading the tool.
1. Press the Magazine Latch (3-8) up and slide the Magazine Side Cover (3-1) back.
2. Holding the nailer with the nose pointing slightly down, insert the brad nails into the
Magazine Side Cover (3-1), letting the pointed end ride on the rail of the Magazine Side
Cover(3-1).
3. After the Nails reach the nose of the tool, close the Magazine Side Cover (3-1) making
sure the Magazine Latch (3-8) clicks shut. See Figure 1 .
Operating the Nailer
1. Attach the Nailer to the air supply at the Air Plug (A-04). Start your compressor and
check the pressure making sure it is set at the recommended 55-95 PSI and not to go
over the maximum 95 PSI.
2. To fire, place the nose of the Nailer on the workpiece. The Nailer should not fire if the
nose is not depressed. Once depressed, gently and briefly squeeze the Trigger (A-26)
once. Do not fire repeatedly. Nails couldbounce off ofone another, damaging thework
piece or causing PERSONAL INJURY.
3. If the brads are being driven too far or not far enough, adjust your air pressure regulator.
Continue to adjust the air pressure until the brads are driven properly.
Magazine Side
Cover (3-1)
Nose Piece* (3-11)
*Also referred to as the
“S”ConnectingPlate.
Magazine
Latch(3-8)
Air Plug (A-04)
Trigger
(A-26)
Figure 1 - Air Nailer Components

SKU 42528 Page 7For technical questions, please call 1-800-444-3353.
Anytime any maintenance or repairs are done (including clearing jams),FIRST:
1. Disconnect the Nailer from the air hose.
2. Empty the Magazine Unit (3-2) completely.
3. Attempt to fire the Nailer into a piece of scrap wood to ensure that it is disconnected
and is incapable of firing any brads.
4. Always leave the Magazine Side Cover (3-1) open during maintenance. The
Magazine is spring-loaded and may cause parts or a nail to fly out of the Nailer.
Clearing Jams
1. Disconnect tool from air hose, empty the Magazine
Unit(3-2) of nails, releaseany built-up air pressure,
and leave the magazine open, as explained above.
2. While doing this step and the next, hold the Nailer
pointed away from you and any other people or
fragile objects - see Figure 2 . Loosen both Screws
(3-15) on the Driver Guide Cover A (3-10) 3/4 of a
turn each - see Figure 3 .
3. Slide the Driver Guide Cover A (3-10) toward the
noseoftheNailerslightlyuntilthe holesinthe Driver
Guide Cover A (3-10) line up with the heads of both Screws (3-15).
4. Carefully remove the Driver Guide Cover A (3-10) and
remove the jammed nail. Pliers may be necessary to
remove a stuck nail.
5. Inspect the Driver Blade (3-18) for bends or breakage.
Ifit is damaged, donotuse the tool untilit is repaired by
a qualified technician.
6. Lightlyoil the DriverBlade (3-18)andreplace theDriver
Guide Cover A (3-10). Slide the Driver Guide Cover A
(3-10) away from the nose of the Nailer until the shafts
oftheScrews(3-15)fit intotheslots inthecover. Tighten
all Screws (3-15) securely.
7. Reload the Nailer.
8. Reconnect the Nailer to the air hose.
9. Press the NosePiece(3-11) of the Naileragainst an
appropriate piece of scrap wood.
10. TestfiretheNailer severaltimes,checkingforproper
operation.
11. Disconnect the Nailer, remove the nails and store
Nailer in a location out of children’s reach.
FIGURE 2
FIGURE 3
Screw
(3-15)
DriverGuide
CoverA
(3-10)
FIGURE 4 DriverBlade
(3-18)

SKU 42528 Page 8For technical questions, please call 1-800-444-3353.
ediuGgnitoohselbuorT
.ruccosmelborpgniwollofehtfoynafiyletaidemmireliaNdarBehtgnisupotS .naicinhcetdeifilauqaybylnoenodebtsumstnemecalpertrapdnasriapeR
naicinhcetdeifilauqaebylnodetpmettaeboteratrahcsihtnodlobniserudecorpllA .
melborPesuaCylekiLnoituloS
.aerareggirTtagnikaelriA gnisuohevlaVreggirTnisgniR-O .degamadera tcatnockcehcdnasgniR-OecalpeR .noitarepopirt
.esoNdnagnisuoHneewtebgnikaelriA .gnisuoHniswercsesooL .)50-A(repmuB/sgniR-OdegamaD .swercsnethgiT .)50-A(repmuBrosgniR-OecalpeR
.metSevlaVreggirTtagnikaelriA .degamaderaslaeSrosgniR-O .slaeSrosgniR-OecalpeR
.paCdnagnisuoHneewtebgnikaelriA .swercsesooL .)21-A(laeSdegamaD .swercSnethgiT .)21-A(laeSecalpeR
.ssolrewopsahroylwolssnuR .liotneiciffusnI .paCrednilyCnignirpSnekorB .dekcolbsi)41-A(paCnitsuahxE
.detcurtsnisaetacirbuL .)31-A(gnirpSecalpeR .strapdegamadecalpeR
.lianaspiksreliaN
degamadro)50-A(repmuBnroW .gnirpSrehsuP .)9-3(ediuGrevirDnitriD .reliaNotwolfriaetauqedanI .notsiPnogniR-OyrdronroW reggirTnogniR-OdegamaD .evlaV .gnikael)21-A(laeSpaC
rehsuPro)50-A(repmuBecalpeR .gnirpS .)9-3(ediuGrevirDnislennahcnaelC .sgnittifrosserpmocdnaesohkcehC .sgniR-OetacirbulroecalpeR .sgniR-OecalpeR
.)21-A(laeSecalpeR
.demmajerasliaN .nrowsirevirdnoediuG .degamadroezisgnorwerasliaN eraswercsesoNroenizagaM .esool .degamadsi)81-3(edalBrevirD
.ediuGecalpeR .sliandegamadnu,tcerrocesU .swercsnethgiT
.)81-3(edalBrevirDecalpeR
.thgitnwodevirdtonlliwreliaN
)81-3(edalBrevirDdednuoR .nworclianffognippils .erusserpriafokcaL .rewopfossoldnagnilcycwolS
.)81-3(edalBrevirDecalpeR
.)ISP59-55(erusserptcerrocylppuS sliocnekorbrof)31-A(gnirpSkcehC erusekaM.htgneldecuderro .raelcsi)41-A(paCnitsuahxe
.ylpeedootliangnivirdedalB notsiPro/dna)50-A(repmuBnroW .recapS .straphtobrorehtieecalpeR
.naicinhcetdeifilauqaebylnodetpmettaeboteratrahcsihtnodlobniserudecorpllA
Anytime any maintenance or repairs are done,FIRST:
1. Disconnect the Nailer from the air hose.
2. Empty the Magazine Unit (3-2) completely.
3. Attempt to fire the Nailer into a piece of scrap wood to ensure that it is disconnected
and is incapable of firing any brads.
4. Always leave the Magazine Side Cover (3-1) open during maintenance. The
Magazine is spring-loaded and may cause parts or a nail to fly out of the Nailer.

SKU 42528 Page 9For technical questions, please call 1-800-444-3353.
Parts List
Part # Description
A-01 Body
A-02 O-Ring
A-03 Bottom Cap
A-04 Air Plug
A-05 Bumper
A-06 Cylinder
A-07 O-Ring
A-07-1 O-Ring
A-08 Collar
A-09 Valve
A-09-1 Stopper
A-09-2 O-Ring
A-09-3 O-Ring
A-10 O-Ring
A-11 Cylinder Cap
A-12 Seal
A-13 Spring
A-14 Cap
A-14-1 Screw
A-17 O-Ring
A-18 Seal
A-19 Seal
A-20 Trigger Valve
A-21 Valve Stem
A-22 O-Ring
A-23 Valve Guide
A-24 O-Ring
A-25 Spring
Part # Description
A-26 Trigger
A-27 Pin
A-28 E-Ring
A-29 Nozzle Cap
A-30 Pin
A31 Connecting Plate
3-1 Magazine Side Cover
3-2 Magazine Unit
3-3 Cover
3-4 Spring
3-5 Pusher Guide
3-6 Pusher
3-7 Support
3-8 Magazine Latch
3-9 Driver Guide
3-10 Driver Guide Cover A
3-11 “S” Connecting Plate*
3-12 Fore Stopper
3-13 Screw
3-14 Screw
3-15 Screw
3-16 Screw
3-17 Screw
3-18 Driver Blade
3-19 Safety Rod
3-20 Snap Ring
3-21 Spring
Maintenance
Warning! Always disconnect the tool from the air compressor and then empty the magazine
of nails before attempting to inspect or perform maintenance to the Nailer.
1. Inspect all of the nuts and screws and make sure they are securely fastened.
2. Periodically lubricate the driving mechanism and magazine with a light oil. Wipe down
with a clean cloth. Never use gasoline or flammable solvents to clean the tool.
3. Inspect your air compressor according to manufacturer’s instructions.
*Referred to as the Nose Piece throughout this manual.

SKU 42528 Page 10For technical questions, please call 1-800-444-3353.
NOTE:Some parts are listed and shown for illustration purposes only and are not available indi-
vidually as replacement parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM AND
TROUBLESHOOTING GUIDE IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE
MANUFACTURERNORDISTRIBUTOR MAKESANYREPRESENTATIONORWARRANTYOFANYKINDTO
THEBUYERTHAT HEORSHEISQUALIFIEDTOMAKEANYREPAIRSTOTHEPRODUCTORTHAT HE OR
SHE IS QUALIFIEDTO REPLACE ANY PARTS OFTHE PRODUCT. IN FACT,THE MANUFACTURER AND/
ORDISTRIBUTOREXPRESSLYSTATESTHAT ALL REPAIRS AND PARTS REPLACEMENTSSHOULDBE
UNDERTAKEN BY CERTIFIED AND LICENSEDTECHNICIANS AND NOT BYTHE BUYER.THE BUYER
ASSUMESALLRISK ANDLIABILITYARISING OUTOFHIS ORHERREPAIRSTOTHEORIGINALPRODUCT
OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF
REPLACEMENT PARTSTHERETO.
Assembly Diagram