Central Pneumatic 99959 Installation manual

AIR OPERATED
SOLVENT/CLEANER
SPRAY GUN
99959
SET UP AND OPERATING INSTRUCTIONS
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright©2008 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
REV 11h

SKU 99959 For technical questions, please call 1-800-444-3353. Page 2
SAVE THIS MANUAL
Keep this manual for the safety warn-
ings and precautions, assembly, operat-
ing, inspection, maintenance and cleaning
procedures. Write the product’s serial
number in the back of the manual near the
assembly diagram (or month and year of
purchase if product has no number). Keep
this manual and the receipt in a safe and
dry place for future reference.
Safety Alert Symbol and Signal
Words
In this manual, on the labeling,
and all other information provid-
ed with this product:
This is the safety alert
symbol. It is used to alert
you to potential personal
injury hazards. Obey all
safety messages that
follow this symbol to avoid
possible injury or death.
DANGER indicates
a hazardous
situation which, if not
avoided, will result in death or
serious injury.
WARNING
indicates a
hazardous situation which, if
not avoided, could result in
death or serious injury.
CAUTION, used
with the safety
alert symbol, indicates a
hazardous situation which, if
not avoided, could result in
minor or moderate injury.
NOTICE is used to
address practices
not related to personal injury.
CAUTION, without
the safety alert
symbol, is used to address
practices not related to
personal injury.
IMPORTANT SAFETY
INSTRUCTIONS
INSTRUCTIONS PERTAINING
TO A RISK OF FIRE,
ELECTRIC SHOCK, OR
INJURY TO PERSONS
WARNING – When using this Spray Gun,
basic precautions should always be
followed, including the following:
General
To reduce the risks of electric shock, re,
and injury, read all the instructions before
using the tool.
Work area
Keep the work area clean and well1.
lighted. Cluttered benches and dark
areas increase the risks of electric
shock, re, and injury.
Keep bystanders, children, and2.
visitors away while operating the
tool. Distractions may result in the
loss of control of the tool.
Personal safety
Stay alert. Watch what you are do-1.
ing and use common sense when
operating the tool. Do not use the

SKU 99959 For technical questions, please call 1-800-444-3353. Page 3
tool while tired or under the inu-
ence of drugs, alcohol, or medica-
tion. A moment of inattention while
operating the tool increases the risk
of injury.
Dress properly.2. Do not wear loose
clothing or jewelry. Contain long
hair. Keep hair, clothing, and
gloves away from moving parts.
Loose clothes, jewelry, or long hair
increases the risk of injury as a result
of being caught in moving parts.
Avoid unintentional starting.3. Be sure
ngers are off Trigger Lever com-
pletely before connecting to the
air supply. Do not carry the tool with
your ngers on the Trigger Lever or
connect the tool to the air supply with
the Trigger Lever open (squeezed).
Do not overreach.4. Keep proper foot-
ing and balance at all times. Proper
footing and balance enables better
control of the Spray Gun in unexpect-
ed situations.
5. Use safety equipment. A
dust mask/respirator, and
non-skid safety shoes
must be used for the
applicable conditions. Wear heavy-
duty work gloves during use.
6. Always wear eye protec-
tion. Wear ANSI-approved
safety goggles.
7. Always wear hearing
protection when using the
tool. Prolonged exposure
to high intensity noise is
able to cause hearing loss.
Risk of Electric Shock.8. This tool is
not provided with an insulated
gripping surface. Contact with a
″live″ wire will also make exposed
metal parts of the tool ″live″ and
shock the operator.
Avoid body contact with grounded9.
surfaces such as pipes, radiators,
ranges and refrigerators. There is an
increased risk of electric shock if your
body is grounded.
Tool use and care
Do not use the tool if the Trigger1.
Lever does not turn the tool on or
off. Any tool that cannot be con-
trolled with it’s Trigger Lever, or on/
off Switch is dangerous and must be
repaired.
Disconnect the tool from the air2.
source before making any adjust-
ments, changing accessories, or stor-
ing the tool. Such preventive safety
measures reduce the risk of accident-
ly discharging uid. Turn off and de-
tach the air supply, safely discharge
any residual air pressure, and release
the Trigger Lever to it’s off position
before leaving the work area.
Store the idle Spray Gun out of3.
reach of children and other un-
trained persons. A tool is dangerous
in the hands of untrained users.
Check for misalignment, cracks, and4.
any other condition that affects the
tool’s operation. If damaged, have
the Spray Gun serviced before using.
Many accidents are caused by poorly
maintained tools. There is a risk of
bursting if the tool is damaged.
Use only accessories that are iden-5.
tied by the manufacturer for the
specic tool model. Use of an acces-

SKU 99959 For technical questions, please call 1-800-444-3353. Page 4
sory not intended for use with the
specic tool model, increases the risk
of injury.
Service
Tool service must be performed1.
only by qualied repair personnel.
When servicing a tool, use only2.
identical replacement parts. Use only
authorized parts.
Use only the lubricants supplied with3.
the tool or specied by the manufac-
turer.
Air source
1. Never connect to an air
source that is capable of
exceeding 200 psi. Over
pressurizing the tool may
cause bursting, abnormal operation,
breakage of the tool or serious injury
to persons. Use only clean, dry,
regulated compressed air at the rated
pressure or within the rated pressure
range as marked on the tool. Always
verify prior to using the tool that the
air source has been adjusted to the
rated air pressure or within the rated
air-pressure range.
Never use oxygen, carbon dioxide,2.
combustible gases or any bottled
gas as an air source for the tool.
Such gases are capable of explosion
and serious injury.
SAVE THESE
INSTRUCTIONS.
SYMBOLS AND
SPECIFIC SAFETY
INSTRUCTIONS
Symbol Denitions
Symbol Property or statement
noNo-load speed
.../min Revolutions or reciprocation per
minute
PSI Pounds per square inch of pressure
ft-lb Foot-pounds of torque
BPM Blows per minute
CFM Cubic Feet per Minute ow
SCFM Cubic Feet per Minute ow at
standard conditions
NPT National pipe thread, tapered
NPS National pipe thread, straight
WARNING marking concerning Risk
of Eye Injury. Wear ANSI-approved
eye protection.
WARNING marking concerning Risk
of Hearing Loss. Wear hearing
protection.
WARNING marking concerning Risk
of Respiratory Injury. Wear NIOSH-
approved dust mask/respirator.
WARNING marking concerning Risk
of Explosion.
Specic Safety Instructions
Warning:1.
To prevent serious injury:
Do not use with gasoline or othera.
ammable or toxic liquids.

SKU 99959 For technical questions, please call 1-800-444-3353. Page 5
Follow solvent supplier instructionsb.
during use.
Keep away from children.c.
DO NOT exceed 90 LB. Air Pres-d.
sure.
WARNING: DO NOT point, or spray2.
contents of this Spray Gun at any
person or animal at any time.
The warnings and precautions dis-3.
cussed in this manual cannot cover
all possible conditions and situations
that may occur. It must be under-
stood by the operator that common
sense and caution are factors which
cannot be built into this product, but
must be supplied by the operator.
Obey the manual for the air compres-4.
sor used to power this tool.
Install an in-line shutoff valve to allow5.
immediate control over the air supply
in an emergency.
This tool is operated under pres-6.
sure. Be sure to keep a rm grip at
all times. Not holding tool rmly at all
times may result in loss of control.
SAVE THESE
INSTRUCTIONS.

SKU 99959 For technical questions, please call 1-800-444-3353. Page 6
FUNCTIONAL DESCRIPTION
Specications
Maximum Air Pressure 90 PSI
Air Inlet 1/4” -18 NPT (Female)
Air Consumption 4 SCFM @ 116 PSI
INITIAL TOOL SET UP/
ASSEMBLY
Read the ENTIRE IMPORTANT
SAFETY INFORMATION
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
Note: For additional information regarding
the parts listed in the following pages,
refer to the Assembly Diagram near
the end of this manual.
Unpacking
When unpacking, check to
make sure that the item is intact
and undamaged. If any parts
are missing or broken, please
call Harbor Freight Tools at the
number shown throughout the
manual as soon as possible.
ASSEMBLY
No assembly is required for this tool1.
with the exception of threading the
Flexible Supply Nozzle (1) onto the
Gun Assembly (2).
This air tool may be shipped with a2.
protective plug covering the air inlet.
Remove this plug before set up.
Air Supply
TO PREVENT
EXPLOSION:
Use only clean, dry, regulated,
compressed air to power this
tool. Do not use oxygen,
carbon dioxide, combustible
gases, or any other bottled
gas as a power source for this
tool.
1. Attach an air hose to the compres-
sor’s air outlet. Connect the air hose
to the air inlet of the tool. Other com-
ponents, such as a connector and
quick coupler, will make operation
more efcient, but are not required.
2. WARNING! TO PREVENT SERI-
OUS INJURY FROM ACCIDENTAL
OPERATION:
Do not install a female quick cou-
pler on the tool. Such a coupler
contains an air valve that will allow
the air tool to retain pressure and op-
erate accidentally after the air supply
is disconnected.

SKU 99959 For technical questions, please call 1-800-444-3353. Page 7
Note: Air ow, and therefore tool perfor-
mance, can be hindered by under-
sized air supply components.
The air hose must be long enough3.
to reach the work area with enough
extra length to allow free movement
while working.
Make sure the Sprayer’s Trigger is4.
in the off position; refer to Operation
section for description of controls.
Close the in-line safety valve be-5.
tween the compressor and the tool.
Turn on the air compressor according6.
to the manufacturer’s directions and
allow it to build up pressure until it
cycles off.
Adjust the air compressor’s output7.
regulator so that the air output is
enough to properly power the tool,
but the output will not exceed the
tool’s maximum air pressure (90
PSI) at any time. Adjust the pres-
sure gradually, while checking the air
output gauge to set the right pressure
range.
Inspect the air connections for leaks.8.
Repair any leaks found.
If the Spray Gun will not be used at9.
this time, turn off and detach the air
supply, safely discharge any residual
air pressure, and release the Trigger
to prevent accidental operation.
Note: Residual air pressure should not be
present after the tool is disconnected
from the air supply. However, it is a
good safety measure to attempt to
discharge the tool in a safe fashion
after disconnecting to ensure that the
tool is disconnected.
OPERATING INSTRUCTIONS
Read the ENTIRE IMPORTANT
SAFETY INFORMATION
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
Inspect the Sprayer before use,
looking for damaged, loose,
and missing parts. If any
problems are found, do not use
Sprayer until repaired.
Tool Set Up
TO PREVENT
SERIOUS INJURY
FROM ACCIDENTAL
OPERATION:
Turn off the tool, detach the
air supply, safely discharge
any residual air pressure in
the tool, and release Trigger
before performing any
inspection, maintenance, or
cleaning procedures.
TO PREVENT SERIOUS
INJURY:
Do not adjust or tamper with
any control or component in a
way not specically explained
within this manual. Improper
adjustment can result in
tool failure or other serious
hazards.

SKU 99959 For technical questions, please call 1-800-444-3353. Page 8
Work Piece and Work Area Set Up
Designate a work area that is clean1.
and well-lit. The work area must not
allow access by children or pets to
prevent injury and distraction.
Route the air hose along a safe route2.
to reach the work area without creat-
ing a tripping hazard or exposing the
air hose to possible damage. The air
hose must be long enough to reach
the work area with enough extra
length to allow free movement while
working.
There must not be objects (such as3.
utility lines or foreign objects) nearby
that will present a hazard while work-
ing.
General Operating Instructions
Spraying Solvents and/or
Cleaners
WARNING: DO NOT point or spray1.
the contents of this Spray Gun at
any person, or animal at any time.
Always wear ANSI-approved safety2.
goggles and heavy-duty work gloves
when using this Sprayer.
Premix solvents and/or cleaners ac-3.
cording to their manufacturer’s in-
structions before adding to the Con-
tainer (3).
Thread the Flexible Discharge Nozzle4.
(1) onto the Gun Assembly (2).
Thread the Container onto the Gun5.
Assembly, making sure not to cross
the threads.
Wrap 3 turns of thread sealing tape6.
on a male connector (not supplied)
and attach it to the end of the handle.
Rotate the nozzle lock ring clockwise7.
until it comes to a stop against the
adjustable nozzle. Rotate the nozzle
cap until it rests against the lock ring.
Turn on air supply.8.
To begin spraying, set the supply air9.
pressure to 90 PSI, point the nozzle
at a safe location, pull the trigger and
lock it with the spring lock. Slowly ro-
tate the nozzle in a counterclockwise
direction until liquid starts spraying
out of the nozzle. Continue rotating
the nozzle for not more than a full
turn and ne tune the spray pattern.
Release the trigger lock. Unscrew
the nozzle lock against the nozzle to
secure it in the preset position. The
tool is not read to be operated.
When nished spraying, or when 10.
relling the Container, release the
Trigger and turn off the air supply.
When you are completely nished 11.
spraying, release the Trigger, turn
off the air supply and disconnect the
compressor from it’s power supply.
Remove the Container and thor-12.
oughly rinse according to directions
supplied by the solvent/liquid manu-
facturer.
Let the Sprayer dry before storing13.
inside out of the reach of children.
CAUTION! TO PREVENT TOOL
AND ACCESSORY FAILURE, RE-
SULTING IN INJURY:
Do not exceed the tool’s maximum
air pressure rating of 90 PSI.
If the tool still does not have sufcient

SKU 99959 For technical questions, please call 1-800-444-3353. Page 9
force at maximum pressure and suf-
cient airow, then a larger tool may
be required.
USER-MAINTENANCE
INSTRUCTIONS
Procedures not specically
explained in this manual
must be performed only by a
qualied technician.
TO PREVENT
SERIOUS INJURY
FROM ACCIDENTAL
OPERATION:
Turn off the tool, detach the
air supply and safely
discharge any residual air
pressure in the tool, before
performing any inspection,
maintenance, or cleaning
procedures.
TO PREVENT SERIOUS
INJURY FROM TOOL
FAILURE:
Do not use damaged
equipment. If abnormal
noise, vibration, or leaking
air occurs, have the problem
corrected before further use.
Cleaning, Maintenance, and
Lubrication
Note: These procedures are in addition to
the regular checks and maintenance
explained as part of the regular op-
eration of the air-operated tool.
Before Use:1.
Check entire Spray Gun Assemblya.
for cracks, loose hoses, worn con-
nections and any other issue that
may prevent safe use of this tool. If
anything abnormal is found, have the
part(s) repaired before further use.
After Use:2.
Rinse entire Spray Gun Assemblya.
with clear, clean water, let dry and
store inside, away from children.

SKU 99959 For technical questions, please call 1-800-444-3353. Page 10
Troubleshooting
Problem Possible Causes Likely Solutions
Decreased output. Not enough air pressure and/1.
or air ow.
Obstructed trigger.2.
Air leaking from loose housing.3.
Mechanism contaminated.4.
Check for loose connections and make sure1.
that air supply is providing enough air ow
(CFM) at required pressure (PSI) to the
tool’s air inlet. Do not exceed maximum air
pressure.
Clean around trigger to ensure free2.
movement.
Make sure housing is properly assembled3.
and tight.
Have qualied technician clean and lubricate 4.
mechanism. Install in-line lter in air supply
as stated in Initial Set Up: Air Supply.
Air leakage. Cross-threaded housing.1.
Loose Gun Assembly.2.
Damaged valve or Gun3.
Assembly.
Dirty, worn or damaged valve.4.
Check for incorrect alignment and uneven1.
gaps. If cross-threaded, disassemble and
replace damaged parts before use.
Tighten Gun Assembly. If Gun Assembly2.
cannot tighten properly, internal parts may be
misaligned.
Replace damaged components.3.
Clean or replace valve assembly.4.
Follow all safety precautions whenever diagnosing or servicing the
tool. Disconnect air supply before service.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT
HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/
OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD
BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE
BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER
INSTALLATION OF REPLACEMENT PARTS THERETO.

SKU 99959 For technical questions, please call 1-800-444-3353. Page 11
PARTS LIST
Part Description Q’ty
1 Flexible Discharge Nozzle 1
2 Gun Assembly 1
3 1 QT. Container 1
PARTS DIAGRAM
Gun Assembly (2) Flexible Supply Nozzle (1)
1 QT. Container (3)
Nozzle Lock Ring
Trigger Lock

SKU 99959 For technical questions, please call 1-800-444-3353. Page 12
90 DAY WARRANTY
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality
and durability standards, and warrants to the original purchaser that this product is free
from defects in materials and workmanship for the period of 90 days from the date of
purchase. This warranty does not apply to damage due directly or indirectly, to misuse,
abuse, negligence or accidents, repairs or alterations outside our facilities, criminal
activity, improper installation, normal wear and tear, or to lack of maintenance. We shall
in no event be liable for death, injuries to persons or property, or for incidental, contingent,
special or consequential damages arising from the use of our product. Some states do
not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation of exclusion may not apply to you. This warranty is expressly in lieu of all other
warranties, express or implied, including the warranties of merchantability and tness.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the complaint
must accompany the merchandise. If our inspection veries the defect, we will either
repair or replace the product at our election or we may elect to refund the purchase price
if we cannot readily and quickly provide you with a replacement. We will return repaired
products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning
the product.
This warranty gives you specic legal rights and you may also have other rights which
vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • [phone]
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
REV 11h