Centro Theatre Set 2 User manual

Centro Theatre Set 2
Assembly Instructions

1
Stand base assembly on the
ground. Loosen grub screws
and slide both connector bars
half way out of channel and
retighten. Repeat for other
base assembly.
2 3
Fully join posts and tighten
remaining grub screws to
make assembly secure.
Repeat for other base post.
Align acrylic cap notches
in upper 8-way post
assembly with protruding
connectors at stage 1.

4.1 4.2.1 4.2.2
4.2.3 The horizontal (H, H1 and H2) and vertical (V and V1) frame profiles
are joined in a similar manner to the posts
4.1) Loosen grub screws and slide connector bars halfway out of
the channel.
4.2) Join profiles ensuring graphic fixing strips are aligned and the
expanding clamps are at either end of the assembled profiles.

4.2i) Centre vertical ‘V1’ differs due to the presence of twin graphic fixing strips.
4.2ii) Bottom horizontal ‘H2’ differs with the introduction of the adjustable thumb screw foot in the centre.
4.3) Tighten grub screws to make secure.
4.2i 4.2ii 4.3

5.1 5.2 5.3
Connect two vertical (V) 1531mm assembly rails at 90º to
each end of the 1500mm horizontal rail (H2) ensuring that the
graphic fixing strip is outermost and the verticals are flush with
the end of the 1500mm rail. Bottom horizontal 1500mm rail (H2)
should have an adjustable thumbscrew foot in the middle of a
260mm connector bar. Connect middle vertical rail (V1- with
twin graphic fixing strips) to centre of the assembled horizontal
(H2) using the expanding clamp. Tighten 3 bottom grub screws
in expanding clamps on verticals to secure to horizontal.

6.1 6.2 6.3
Connect second horizontal 1500mm rail assembly (H),
using the expanding clamps, to top of assembled
verticals (V, V1 and V) ensuring that the graphic fixing
strip is at the bottom. Tighten grub screws on vertical
rails to secure. This completes the bottom section of
the framework.

7.1 7.2 7.3
For the top section of the framework, connect the two
220mm profiles, with expanding clamps at both ends
and the single fixing strip, at 90º flush to each end of
the third 1500mm horizontal rail (H). Ensure that the
graphic fixing strip on the verticals are outermost and
the graphic fixing strip on the horizontal 1500mm rail is
at the top. Affix 220mm vertical profile, with expanding
clamps at both ends and twin fixing strip, to middle of
1500mm horizontal. Tighten lower grub screws adjacent
to horizontal rail assembly to secure 220mm verticals.

8.1 8.2 8.3
Slot final top horizontal 1500mm rail assembly (H1)
to the 220mm verticals, ensuring that the graphic
fixing strip is at the top. Tighten grub screws on
verticals to secure framework. This completes the
top section of the framework.

9.1 9.2
Slot the bottom section framework into the channel of the
assembled post at 90º to the base plate. Ensure framework is
equidistant from the base plate, adjustable foot rests on the
ground, and graphic fixing strip is adjacent to the floor.
Tighten both grub screws in the horizontals (H2 and H) to secure.

Slot open end of framework into other assembled post, at 90º
to the base plate. Ensure bottom section is equidistant from
the floor at both ends and the adjustable foot rests on the floor.
Tighten remaining grub screws in horizontals (H2 and H) to
secure bottom section framework to both post assemblies.
10.1 10.2

Affix the top section framework into the same channel as the
bottom section ensuring graphic fixing strips are all on the
same side of the system. Leave a gap of 60mm in between
bottom and top framework assemblies and tighten all grub
screws in horizontals (H and H1) to secure to post.
11.1 11.2

Prepare and cut aperture
in graphic according to the
graphic spec appropriate
to the desired screen size.
Apply magnetic tape to
rear of graphic panels in
locations shown on graphic
spec and affix completed
panels to framework.
12.1 12.2
13
npack the LCD/Plasma
Screen Mounting Bracket, 4 off
260mm connector bars, and 4
suitable screws and washers
to thread into connector bars.

14.1 14.2 14.3
14.4 Insert 2 screws through upper
corner mount holes as shown
and clearance holes in 2 off
connector bars. Position mount
centrally over upper horizontal
rail in aperture and screw (not
fully) into other 2 off 260mm
connector bars, situated on the
other side of the horizontal rail,
to hold in position.

15.1 15.2 15.3
Raise screen mount so
bottom holes are above the
lower horizontal rail in
aperture. Insert remaining 2
screws through lower mount
holes (4 openings from
either end of the screen
mount) and clearance holes
in 2 off 260mm connector
bars adjacent to mount.

16.1 16.2
Align other 2 off 260mm
connector bars, located behind
horizontal rails, and screw into
threaded holes. Ensure bottom
screws rest on lower horizontal
rail, mount is in centre of
aperture, and tighten all 4
screws to secure assembly.

18
Position screen centrally
above bracket and lower until
top of both mounting arms
hook over mount.
17
With the elongated holes
on the mounting arms
uppermost, align arms
centrally with 4 off fixing
points on rear of screen
equidistant from the top.
Insert 4 off screws with
suitable washers and tighten.

19.1
Slide locking bar between
the mounting arms and the
plasma mounting bracket if
desired. For extra security,
there is a facility to add a
padlock to the locking bar.
19.2

20
To complete Centro Theatre Set 2 display,
please affix podium table to the front of
one of the posts.