Centuri Phoenix User manual

SERVICE MANUAL
LJ
364-62-0100 A

TABLE OF CONTENTS
PAGE NO.
I. INTRODUCTION ;
USER INFORMATION -F.C.C. 1
GAME DESCRIPTION (DIAGRAM) 2
GAME SUMMARY 3,4
II. SPECIFICATIONS :
INSTALLATION 4
ELECTRICAL REQUIREMENTS 4
110/220 CONVERSION INSTRUCTIONS 5
III. OPERATION:
GAME INSTRUCTIONS
GAME SCORING
ROUTINE MAINTENANCE AND SERVICE
OPERATOR OPTIONAL SWITCH SETTINGS
OPTIONAL SWITCH SETTINGS
IV. GENERAL :
C.P.U. PARTS LIST
LOGIC BOARD PARTS LIST
SHINDENGEN POWER SUPPLY PARTS LIST
DRAWINGS
:
110/220 POWER INTERCONNECT DIAGRAM (361-10-0900) 14
C.P.U. HARNESS INTERCONNECT DIAGRAM (364-10-1000) 15
SHINDENGEN POWER SUPPLY SCHEMATIC (363-17-0300) 16
C.P.U. BOARD SCHEMATIC (364-62-0900) 17
LOGIC BOARD SCHEMATIC (364-62-0800) 18
COIN DOOR WIRING DIAGRAM (364-62-1000) 19
9, 10
11
12, 13
6
6
7
8
8

#364-62-0600
USER INFORMATION -F.C.C.
WARNING:
This equipment generates, uses and can radiate
radio frequency energy and if not installed and
used in accordance with the instructions manual,
may cause interference to radio communications.
As temporarily permitted by regulation, it has
not been tested for compliance pursuant to Subpart
Jof Part 15 of F.C.C. Rules, which are designed
to provide reasonable protection against such inter-
ference. Operation of this equipment in aresidential
area is likely to cause interference in which case the
user at his own expense will be required to take
whatever measures may be required to correct the
interference
.
-1-

CONTROL PANEL
LEFT MOTION i
BUTTON
RIGHT MOTION I
BUTTON '
LINE CORD
^RQUEE
-VIEWING GLASS
BEZEL
-1-PLAYER BUTTON
2-PLAYER BUTTON
•FIRE BUTTON
FORCE FIELD BUTTON
•COIN DOOR ASSEMBLY
PHOENIX VIDEO UPRIGHT

PHOENIX
PHOENIX is an exciting new space game, with special
audio and visual effects, challenging the skills of the
most experienced player. Fascinating visual graphics
and extraterrestrial sounds add to the intensity of
this game.
There are five basic stages to- each round of play.
After amelodious introduction, the first stage begins
with awave of sixteen (16) small Phoenixes attacking
the spaceship. They drop missiles and dive at the
spaceship, in an effort to destroy it.
The spaceship maneuvers left and right, evading
the missiles and birds, and fires rockets, attempting
to destroy the birds.
The spaceship can utilize the "Force Field" as a
means of protection from the missiles and birds, and
can destroy the Phoenixes by colliding with them while
in the Force Field. The Force Field only lasts afew
seconds and then cannot be used for approximately five
(5) seconds afterward.
After the first wave of Phoenixes are destroyed,
asecond wave appears, and can be destroyed in the
same manner as in the first stage.
The third stage begins with awave of eight (8)
"Eggs" that are transformed into blue Phoenix birds
that attack the spaceship. These birds can be des-
troyed by rocket fire from the spaceship. If the
rocket hits the bird on center, the bird is destroyed.
If the rocket hits the bird to the left or right of
center, only that wing of the bird is destroyed.
The wing will regenerate itself in ashort time.
After all the blue Phoenixes have been shot down,
the fourth stage appears on the screen. Two banks of
eggs appear (four eggs in each row) ,and are transformed
into pink Phoenixes, and can be destroyed in the same
manner as the blue birds.
The fifth stage is the attack of the spacefortress
,
which sends down waves of small birds to attack the
spaceship, in addition to direct missile fire from
the spacefortress. Spaceship rocket fire can penetrate
and break down the protective barrier shielding the
space creature in the spacefortress. The fifth stage
-3-

is completed when the rocket from the spaceship destroys
the space creature and the spacefortress with adirect
hit.
Good aim and timing are critical to high scoring.
Birds destroyed while in flight (with wings flapping)
,
will score 200 points each, and eggs hit in the process
of hatching also have higher point values
.
Delayed destruction of the spacefortress also gives the
player high point values.
When bonus levels are achieved, additional space-
ships are added to your game. The bonus level
adjusted to award bonus spaceships at 3,000 and 30,000
points, 4,000 and 40,000 points, 5,000 and 50,000 points,
or 6,000 and 60,000 points.
INSTALLATION
Your game was shipped from the factory in ready-to—
play condition. Abrief inspection is suggested before
the machine is removed from the carton. If there is
damage to the shipping carton, contact the freight
carrier for claim purposes. External damage could
indicate possible damage to the cabinet and/or electronic
components
.
After the carton has been satisfactorily inspected,
remove the machine from the shipping carton.
Examine the interior of the game for disconnected
wires, cables or harnesses and make sure electronic
devices are securely mounted in their sockets, etc.
Record the game serial number, since it will be re-
quired for reference and servicing.
ELECTRICAL REQUIREMENTS
Unless otherwise specified, this game is set to
operate at 110 Volts A.C. See Figure -1- for 110/220
VAC conversion instructions.
Power Supply Chassis schematic information and
parts list are included in this manual.
-4-

FIGURE -1-
110/220 VAC CONVERSION INSTRUCTIONS
1. This video arcade game has aharnessing
configuration that allows the machine to
be operated from either a110 VAC or 220
VAC @50 or 60 power source, with only
minor changes. The only items requiring
achange are the fuses and the jumper plug
on the game power transformer.
2. First, unplug the machine from the wall
outlet to completely eliminate shock hazards.
3. Next, remove the two fuses in the A.C.
distribution bracket.
4. Then, remove the jumper plug on the game
power transformer located on the floor of
the machine.
5. Now, depending on what voltage you wish to
run the game from, do the following:
110 VAC :Replace the two fuses that go in
the bracket with 3-AMP SLOW-BLOW
types. Next, plug in the ORANGE
jumper plug labeled 110 VAC.
The machine can now be operated
with an input voltage of 110 Volts AC.
220 VAC :Replace the two fuses that go in the
bracket with Ih AMP SLOW-BLOW types.
Next, plug in the RED jumper plug
labeled 220 VAC. The machine can
now be operated with an input voltage
of 220 Volts AC.
NOTE: All games shipped from CENTURI ,INC. are in
the 110 VAC configuration.
-5-

GAME INSTRUCTIONS;
1. INSERT COIN(S) INTO SLOT.
2. SELECT 1OR 2PLAYER BUTTON.
3. MOVE THE SPACESHIP RIGHT AND LEFT, DODGING
FROM ATTACK OF PHOENIX AND DESTROYING IT
BY FIRING BUTTON.
4. SHELTER SPACESHIP BY PRESSING FORCE FIELD
BUTTON
.
5. ADDITIONAL SPACESHIP IS ADDED WHEN BONUS
SCORE IS ACHIEVED.
6. THE GAME IS OVER WHEN ALL THE SPACESHIPS
HAVE BEEN DESTROYED.
GAME SCORING:
=20, 40 and 80 Points.
=200 Points.
=50 to 100 Points
(Hatching =100 to 800 Points)
.
=1,000 to 9,000 Points.
-6-

ROUTINE MAINTENANCE &SERVICE
Because of the solid state electronic circuitry,
this machine should require very little maintenance
and only occasional adjustments. However, it is
necessary to take measures to insure this.
The volume control is located on the bottom side
of the printed circuit board farthest from the side
of the^ cabinet, and can be accessed through the rear
door.
The video monitor has been properly adjusted
before shipping. Occasionally minor adjustments are
necessary, see monitor specifications and schematics
for technical information. Adjustment controls for
the monitor are located at the rear of the monitor.
This machine should be serviced only by aqualified
technician.
Do not make any adjustments on this machine while
the power is on.
For service information, contact:
CENTURI ,INC
.
Customer Service Department
#800-327-7710 (Outside the state of Florida)
#305-556-5888 (In Florida)
-7-

OPERATOR OPTIONAL SWITCH SETTINGS
The option switches are located on the CPU board.
The option switches and audio control can be reached
through the back of the machine
.
The following settings will assist you with your
selections
;
OPTIONAL SWITCH SETTINGS
Switches 1and 2control the number of times the
player may have his spaceship destroyed before the game
is over. The following truth table lists these switch
settings
:
SWITCH 1:SWITCH 2: NUMBER OF SPACESHIPS:
OFF OFF 6
ON OFF 5
OFF ON 4
ON ON 3
Switches 3and 4control the score at which one or
two free spaceships are awarded according to the follow
ing truth table
:
FIRST FREE SECOND FREE
SWITCH 3: SWITCH 4: SHIP SCORE: SHIP SCORE:
OFF OFF 6,000 60,000
ON OFF 5,000 50,000
OFF ON 4,000 40,000
ON ON 3,000 30,000
SWITCH 5;OFF -25 <: PER GAME.
ON -50<: PER GAME.
Switches 6, 7and 8are factory adjustments, and must
be left in OFF position.
-8-

CPU BOARD ASSEMBLY #50330008
PARTS LIST
NO. PART NUMBER: DESCRIPTION
:
USA(
150010249LS 74LS245 I.C. 1
250010252LS 74LS374 I.C. 3
350010273LS 74LS244 I.C. 2
450010275LS 74LS136 I.C. 1
550010248LS 74LS138 I.C. 4
650010221LS 74LS163 I.C. 3
750010045LS 74LS157 I.C. 3
850010002LS 74LS00 I.C. 4
950010096LS 74LS08 I.C. 3
10 50010141LS 74LS125 I.C. 1
11 50010105LS 74LS32 I.C. 4
12 50010170LS 74LS14 I.C. 1
13 50010019LS 74LS74 I.C. 3
14 50010026LS 74LS107 I.C. 1
15 50010030LS 74LS174 I.C. 1
16 50010276LS 74L470 I.C. 1
17 50010197 7405 I.C. 2
18 50010142 7407 I.C. 1
19 50010277 8085 C.P.U. 1
20 50020003 LM380 I.C. 1
21 50010254 LM324 I.C. 2
22 50010001 555 Timer I.C. 5
23 50010281 4006 I.C. 1
24 50020086 564 Transistor 1
25 50040082 .047 mfd, 25 V. Disc Ceramic Capacitor 13
26 50040001 .Imfd, 25 V. Disc Ceramic Capacitor 2
27 50040141 .OOlmfd, 50 V. Disc Ceramic Capacitor 7
28 50040151 330pf, 25 V. Disc Ceramic Capacitor 1
29 50040049 .Olmfd, 25 V. Disc Ceramic Capacitor 2
30 50040153 .022mfd, 25 V., Disc Ceramic Capacitor 1
31 50060104 47mfd, 50 V. Alum. Lytic Rad. Cap. 4
32 50060031 lOOmfd, 25V., Alum. Lytic Rad. Cap. 1
33 50060126 470mfd, 30 V. ,Alum. Lytic Rad. Cap. 1
34 50060120 lOmfd, 16 V., Alum. Lytic Rad. Cap. 1
35 50060165 10 mfd, 2 5 V. ,Dipped Tantalum Cap. 9
36 50060166 .47mfd, 35 V., Dipped Tantalum Cap. 1
37 50060163 Imfd, 35 V. ,Dipped Tantalum Cap. 2
38 50060145 6.8mfd, 25 V., Dipped Tantalum Cap. 2
39 50120004 lOK PCB Trimmer Potentiometer 1
40 50360007 5-Pin Resistor, IK Ohm 1
41 50360006 9-Pin Resistor Pack, IK Ohm 3
42 50030256 100 Ohm, %W. ,5% Resistor 8
43 50030051 IK Ohm, %W. ,Resistor 12
44 50030056 2.7K Ohm, %W. ,Resistor 2
45 50030063 lOK Ohm, %W. ,5% Resistor 16
46 50030014 270 Ohm, %W. ,5% Resistor 9
47 50030150 47K Ohm, %W. ,5% Resistor 9
48 50030095 330 Ohm, ,5% Resistor 2
49 50030007 lOOK Ohm, %W. ,5% Resistor 4
50 50030010 470 Ohm, ^W. ,5% Resistor 2
-9-

CPU BOARD ASSEMBLY
PARTS LIST #50330008
NO. PART NUMBER ;
51 50030086
52 50030197
53 50030265
54 50030266
55 50100014
56 50150214
57 50150060
58 50150158
59 50150110
60 50150111
61 50150112
62 50040136
63 50130034
64 50150256
65 50210217
66 364-10-0300
DESCRIPTION; USAGE
;
33K Ohm, ^sW. ,5% Resistor 6
5. IK Ohm, 3sW. ,5% Resistor 3
510K Ohm, hVl. ,5% Resistor 2
20K Ohm, ,5% Resistor 1
1N914 Diode 7
8-Pin Solder Tail Socket, Low Profile 5
40-Pin Solder Tail Socket, Low Prof. 1
20-Pin Solder Tail Socket, Low Prof. 6
14-Pin Solder Tail Socket, Low Prof. 25
16-Pin Solder Tail Socket, Low Prof. 13
18-Pin Solder Tail Socket, Low Prof. 1
.05mf, Mylar Capacitor 1
8-Position Dip Switch 1
50-Pin PCB Header, Ainsley #609-5007ES 2
Printed Circuit Board -CPU 1
P.C.B. Interconnect Cable 2
-10-

LOGIC BOARD ASSEMBLY #50330009
PARTS LIST
NO. PART NUMBER: DESCRIPTION: USAGE
15001022LS 74LS163 I.C. 4
250010022LS 74LS86 I.C. 4
350010019LS 74LS74 I.C. 1
450010274LS 74LS132 I.C. 1
550010262LS 74LS283 I.C. 3
650010252LS 74LS374 I.C. 3
750010093LS 74LS151 I.C. 4
850010030LS 74LS174 I.C. 4
950010045LS 74LS157 I.C. 4
10 50010249LS 74LS245 I.C. 2
11 50010005 7404 I.C. 1
12 50010185 2716 I.C. 12
13 50010242 2114 I.C. 8
14 50010273LS 74LS244 I.C. 1
15 50040082 .047mf, 25 V., Disc Ceramic Cap. 7
16 50040141 .OOlmf, 50 V., Disc Ceramic Cap. 2
17 50040049 .Olmf, 25 V., Disc Ceramic Cap. 2
18 50040150 390pf, 25V., Ceramic Disc Cap. 1
19 50040001 .Imf ,25 V., Ceramic Disc Cap. 15
20 50040142 150 pf, 50 V., Disc Ceramic Cap. 1
21 50060028 22mf, Alum. Lytic Radial Cap. 1
22 50070014 IIMH2Crystal 1
23 50030004 1.2k, %W. ,5% Resistor 2
24 50030111 100 Ohm, %W. ,5% Resistor 1
25 50150110 14-Pin Solder Tail Socket, Low Profile 8
26 50150111 16-Pin Solder Tail Socket, Low Profile 19
27 50150112 18-Pin Solder Tail Socket, Low Profile 8
28 50150158 20-Pin Solder Tail Socket, Low Profile 6
29 50150061 24-Pin Solder Tail Socket, Low Profile 12
30 50150256 50-Pin P.C.B. Header, Ansley#609-5007ES 2
31 50210216 P.C. Board, Logic 1
-11-

PARTS LIST -SHINDENGEN POWER SUPPLY
SYMBOL
:
DESCRIPTION: USAGE
T1 Transformer, Single Phase, 24 VA 1
LI Choking Coil, 1.6 mH, 1.5A 1
L2, L4 Choking Coil, SF-T8-50S-03 2
L3 Choking Coil, SF-HP-2A-03 1
Dl Diode, V19G 1
D2 Diode, V06C 1
D3, D6 Diode, 1S1588 2
D4 Diode, S15S3 1
D5, D7 Diode, 5CH1M 2
D12, D13 Diode, F113B 2
D14 Diode, F113B 1
RFl Diode, S4VB40 (Bridge Type) 1
Q1 Transistor, 2SC2504 1
Q2 Transistor, 2SD467 (B) 1
Q3 Transistor, 2SC460(B) 1
Q4 Transistor, 2SA673(B) 1
ICl Integrated Circuit, RM723DC or 1
HA17723G-02
PCI Photo Coupler, PS2001 1
Rl Resistor
,
2Watt, 18 Ohm 1
R8, R9 Resistor
,
2Watt, 47K Ohm 2
R3, 1-4 Resistor, 2Watt, 15 Ohm 4
R4 Resistor, 1Watt, 56 Ohm 1
R12 Resistor
,
1Watt, 100 Ohm 1
R28 Resistor, 1Watt, 470 Ohm 1
R7 Resistor
,
1Watt, 0. 56 Ohm 1
R26 Resistor
,
1Watt, 0. 82 Ohm 1
R23 Resistor, 1/4 Watt, 22 Ohm 1
RIO Resistor
,
1/4 Watt, 33 Ohm 1
R27 Resistor, 1/4 Watt, 68 Ohm 1
R2 Resistor
,
1/4 Watt, 330 -470 Ohm 1
R22 Resistor, 1/4 Watt, 220 Ohm 1
R21 Resistor, 1/4 Watt, 270 Ohm 1
R6 Resistor
,
1/4 Watt, 330 Ohm 1
Rll Resistor
,
1/4 Watt, 68 Ohm 1
R20 Resistor
,
1/4 Watt, 470 Ohm 1
R17 Resistor
,
1/4 Watt, 680 Ohm 1
R19 Resistor
,
1/4 Watt, 800 Ohm 1
R18 Resistor
,
1/4 Watt, 1.2K Ohm 1
R5 Resistor
,
1/4 Watt, lOK Ohm 1
R16 Resistor
,
1/4 Watt, 22OK Ohm 1
R29 Resistor
,
3Watt, 27 Ohm 1
R39 Resistor, 1/4 Watt
,
4.7K Ohm 1
R38 Resistor, 1/4 Watt, 5.6K Ohm 1
R24 Resistor, 1/4 Watt, 330 Ohm 1
R2 5Resistor
,
1/4 Watt, 150 Ohm 1
RVl Variable Resistor, RJ-6P501 1
-12-

PARTS LIST -SHINDENGEN POWER SUPPLY
SYMBOL
:
DESCRIPTION: USAGE
Cl, C2 Capacitor
,
ECK-DAL102E 2
C3-l,-2 Capacitor
,
160VSN100 2
C9, CIO Capacitor
,
SMlOVB-2200 2
Cll, C23 Capacitor
,
SMlOVB-2200 2
C12, C13,C15 Capacitor
,
SL25VB-10 3
021 Capacitor
,
SL25VB-10 1
C18,C19,C20 Capacitor
,
SM35VB-1000 3
C2 6Capacitor
,
SM35VB-1000 1
C21,C22 ,C25 Capacitor
,
SM16VB-1000 3
C5 .Capacitor
,
DMY21H472K 1
C6 Capacitor
,
DMY21H104K 1
C14,C16 Capacitor
,
DMY21H222K 2
C4 Capacitor
,
CM20XC511K5 1
C8 Capacitor
,
MDD22G473K 1
C5-2 Capacitor
,
DMY21H222K 1
FI, F2 Enclosed Type Fuse, 3A 2
-13-

THE MXrtlllAL eONmiMBD HEfICIN 18 CONFIDENTIAL
ANDNOFART OF IT CAN BE NEFRODUCED WITHOUT THE
EXFNEtBBNFENMIBtlON OF ALLIED LEISURE MD., INC.
ZNPur
7UMPBH RecBpr.
ru3E
-1 kl
3J
(ifl
•T
--6
<
-H CQKCOM
une
Ftcren.
-i
a£CrROA//<!S OG
fi ipi
i.
-
3-
•
-
09^/6'^
V2IS3
r.t^, c«s^5
CABINET 3W.
HHHIiziJiyjAV] OTY. ASSCMtlY CM
REVISION BY
TOLERANCES
UnlosB QlKorwiso Spoctfiod
FRACTIONS ±l/St
DECHMALBEFL .OIS
DECIMALS 3FL 5.006
HOLES X)03
.001
ANSLES +lA^
SHTMETBENDS jh 2®
4LUE0 LEISURE INDUSTRIES,INC.
HIALEAH, FLORIDA.33014
name rtfo^Niy. -i?" rUojzzo VTov\^ iNTiEKaimecr 2>J^.
MATL'S. heat treat. TINISH
DWN.jCZ) nri^lSH DATi {scale Irart no IREV.
i-i¥-8L 1 1 ^L>l-iO~0900 11

THE MATERIAL CONTAINED HEREIN IS CONFIDENTIAL
AND NOPART OF IT CAN BE REPRODUCED WITHOUT THE
EXPRESSED PERMISSION OF ALLIED LEISURE il«.,INC.
A
CPU
£Ot-S
\e, R
lljB
JD ,
4-
MONlTCNt
J7 P7 Co rf DM
2xz
ss St (Xah
;5
cs> 4BtV
99 jr cyj#*
s-^/A/‘ns/ (
To
OV -
-2.‘Iptd,
3-2Ptit
5..UDPT
6- -FMC
KAM9S.
7,
1
.F.r
,
CHASSIS
QY ^VV£^S«PP<-T
^.5V OUTPUTS
4t2y
OV
“5Tr
14’
GC)MN7
isJ -5V^
.Al/'
zc -0r
/‘MM
3
J/MM
^-
*4-
\jfc***
dies,
(1
COIN
OOU^
AMP Cam.
Contko l
PAHfL
»X-P|p4 M0U6A AeccPt^c/e
TOLiRANCiS
Unloss Othorwts* SpociHod
FRACTIONS ±I/St
QC. APVb PROO.APVb OTYo ASSSMiLT our
HIALEAH, FLORIDA.33014
DECIMALStPL ±.018
DECIMALS 3PL ±.006
HOLI3 t«f
ANCLES tl/t*
SHT. METBENDS 4- t®
MAIL'S. HIAF TtCAT.
HHDATS SCALf rUT NO. .^1*..^
36 1+- 1(9-/000
-15-

REVISIONS
er 6
z
3E
ECN
NO. DESCRIPTION DISPOSITION
OF EXISTING
PARTS
UJ RE
WORK SCRAP
-DS
TOLERANCES CENTURI, INC.
1780 W. 4th AVENUE HIALEAH, FLORIDA 33010
UNLESS OTHERWISE SPECIFIED
FRACUONS. ±1/32
DECIMALS ±.03
DECIMALS ±.010
HOLES ±
ANGLES ±1/2“
TITLE:
SHINb£AI<$eA/ POW£f?
DWN ,APP’D, DATE SCALE DWG NO. REV
»«: 3&3- 17-0300
NEXT ASSEMBLY
ENGR'G APP’D

BRUNtNG
40-21
19207

Table of contents
Popular Arcade Game Machine manuals by other brands

Merit
Merit FORCE Upright Removal/Installation Instructions

Pop-A-Shot
Pop-A-Shot PRO DUAL SHOT owner's manual

MD SPORTS
MD SPORTS DH18408 Assembly instructions

PlayMechanix
PlayMechanix HALO FIRETEAM RAVEN Setup and Operaton Service Manual

MD SPORTS
MD SPORTS 54804 Assembly instructions

MD SPORTS
MD SPORTS SOC056 117B Assembly instructions

MD SPORTS
MD SPORTS ARC084 168B Series Assembly instructions

MD SPORTS
MD SPORTS FS058Y21006 Assembly instructions

Bay Tek Games
Bay Tek Games Chameleon Paradize Service manual

Bay Tek Games
Bay Tek Games Big Bass Wheel Pro troubleshooting guide

MD SPORTS
MD SPORTS 1515052 Assembly instructions

NAMCO
NAMCO Rave Racer Upgrade manual