CenturionPro Original User manual

For more information or to watch our video tutorials visit cprosolutions.com 1
OWNERS MANUAL
The Original & Silver Bullet
cprosolutions.com
1 855 535 0558
[email protected]

cprosolutions. 1 855 535 0558
2
OWNERS MANUAL
The Original & Silver Bullet

For more information or to watch our video tutorials visit cprosolutions.com 3
TABLE OF CONTENTS
Important Safety Information 4
Machine Assembly 5
Cover Assembly 6
Triple-Bag Kief Collection System 7
Leaf Collector Assembly 8
Hopper Assembly 9
Blade Removal 10
Cleaning the Original & Silver Bullet 10
Leaf Collector Cleaning 11
Machine Maintenance 12
Quantanium Coated Non-Stick Tumbler 13
Warranty Information 14
Frequently Asked Questions 15
Additional Assistance 16
Original & Silver Bullet Machine and 17
Leaf Collector Specifications
Trimming Dry? Here Are Some Important Tips 18
Trim Both Wet and Dry 19
Troubleshooting 20-21

cprosolutions. 1 855 535 0558
4
IMPORTANT SAFETY INFORMATION
This document refers to the CenturionPro Solutions Original & Silver Bullet
automated trimming systems.
The Original & Silver Bullet are high-speed trimming systems, requiring that
specific safety precautions are practiced during operation to reduce the risk of
personal injury. Improper use of The Original, Silver Bullet, or any Centurion Pro
trimming machine, may cause serious or fatal injury. Please ensure you read the
operations manual and warning notes before using the Original or Silver Bullet.
Do not lend out or rent your Original or Silver Bullet without this operating
manual. A first time user should obtain proper instruction prior to use.
GENERAL
• Do not move, disassemble, clean or inspect the trimmer while the power is still connected to the machine.
• Replacement parts are specific to The Original & Silver Bullet and must be purchased from an authorized
dealer only. Substituting factory parts with non-approved third-party replacements may result in damage to
the machine or bodily harm.
• Keep all individuals a safe distance from the work area. Do not operate the machine around children.
• Do not remove safety labels. Replace any and all labels if they become damaged or obscured.
CONNECTION
• As with home appliances, The Original & Silver Bullet must be used in connection with a properly grounded
receptacle.
• Never plug in or power up your trimming machine if the protective shrouds are removed.
• Do not use extension cords over 8m (25ft) in length to power the Original or Silver Bullet.
OPERATION
• The initial set up will show assembly instructions to unpack and set-up your machine.
• Your bed bar blade has been factory set to cut perfectly. Please do not adjust your blade until it is time to
clean the machine. Also, please watch the video tutorial located on our website on how to adjust your blade
before attempting.
• Safety glasses should be worn at all times while operating The Original or Silver Bullet.
• Do not operate any trimming machine while tired or under the influence of medication, drugs or alcohol.
• Do not put anything other than plant material into the tumbler. Doing so may cause damage to the tumbler,
the machine or result in bodily harm.
• Operate the trimmer in a well ventilated area in order to prevent overheating.
MAINTENANCE
• Never leave The Original or Silver Bullet system running unattended.
• Never conduct maintenance or cleaning while the machine is plugged in.
• Do not modify or adapt any part of the trimmer or its accessories. Doing so may cause irreversible damage
to the machine or result in bodily harm.
IMPORTANT

For more information or to watch our video tutorials visit cprosolutions.com 5
MACHINE ASSEMBLY
TOOLS REQUIRED
1 x #2 Phillips Screwdriver
1 x 3/32" T-Handle Allen Wrench
1 x 5/32" T-Handle Allen Wrench
1 x 1/8" T-Handle Allen Wrench
1 x 3/16" T-Handle Allen Wrench
1 x 3/8" Wrench
Tighten Four Sealing
Bolts & Washers
Note the longer end of the
TUMBLER when re-installing
Cover
Brush
Upper Frame
Tumbler
Blade
Adjusters
Requires Cleaning
See Page 10
Tumbler O-Ring
Cutting Reel
Lower Frame Shroud
(area behind cutting reel)
Requires Cleaning
See Page10
Requires Cleaning
See Page 10
Requires Cleaning
See Page 10
Bed Bar Blade &
Magnet Bar
STEP 1
PLACE
TUMBLER IN
GROOVES
STEP 3
INSTALL
COVER
STEP 2
INSTALL
UPPER
FRAME
STEP 4
INSTALL
SKIRT
(INSTALLED ON THE
MACHINE WHEN
SHIPPED)
110V
220V
North
America
Australia
EU
Motor

cprosolutions. 1 855 535 0558
6
COVER ASSEMBLY
It is UNSAFE to operate the ORIGINAL or SILVER BULLET TRIMMER without COVERS!
STEP 1
Attach the BEARING COVER to the ORIGINAL
or SILVER BULLET
STEP 2
Attach the BELT COVER to the ORIGINAL
or SILVER BULLET
Belt Cover
4x Washers
4x Bolts
Belt Cover
Bearing Cover
2 x Washers
2 x Bolts
Bearing Cover

For more information or to watch our video tutorials visit cprosolutions.com 7
TRIPLE-BAG KIEF COLLECTION SYSTEM
Kief is becoming wildly popular due to the rise of extractions. Unfortunately, machines that require
sprays can contaminate and destroy your Kief, therefore making it virtually useless.
Thankfully, CenturionPro offers an optional non-stick Quantanium coating on the tumblers. This means
no spray is needed so your Kief remains 100% pure and usable. To further benefit growers, we devel-
oped a new triple-bag filtration system. This system will assist with Kief collection, separating it from
your trim. This allows you to safely and easily collect the precious trichomes for further processing and
profits.
With your machine, you will see that you have a black mesh bag, a white nylon bag, and an outer cloth
bag. The black bag goes inside the white nylon bag, which then goes inside the white cloth bag.
The bags are easy to wash with a pressure washer using cold water. The bags can also be put through
the washing machine, but it is recommended to be run through on a cold delicate cycle only.
The green leafy trim will collect in the new
inner black bag.
Only the Kief makes it through the black bag
and collects in the outer mesh bag.
Outer cloth bag catches any Kief that may
pass through the micron white bag.
Turn off the machine and remove the inner
bag and then extract Kief. ENJOY!
HOW IT WORKS

cprosolutions. 1 855 535 0558
8
LEAF COLLECTOR ASSEMBLY
4” Flex Hose
Secure with one 4”
hose clamp
Zipper
Leaf Collector Bag System Leaf Collector
Secure with
4” hose clamps
Requires Cleaning
See Page 11
Requires Cleaning
See Page 11
Secure with 4”
Hose Clamps
110V
220V
North
America
Australia
EU
STEP 1
ATTACH BAG
SYSTEM TO LEAF
COLLECTOR
STEP 2
ATTACH 4" FLEX
HOSE TO THE
DIVERTER AND
ORIGINAL OR
SILVER BULLET
Please disregard hole on
top of diverter, the suction
will hold the diverter in
place and no screw is
needed to secure.

For more information or to watch our video tutorials visit cprosolutions.com 9
HOPPER ASSEMBLY
STEP 1
ASSEMBLE
THE FRAME
STEP 2
SECURE THE
HOPPER BAG TO
THE FRAME
STEP 3
CONNECT THE
HOPPER TO THE
MACHINE
Inward
Hopper
Bag
Opening Frame (Back)
Frame (Front)
Ensure the
OPENING and
FRAME (front) match
Ensure the RODS are
facing inward. Secure with
1/4" BOLTS, WASHERS
& LOCKING NUTS
Ensure the Frame and OPENING
match the ORIGINAL & SILVER BULLET
machine exactly

cprosolutions. 1 855 535 0558
10
WARNING:
Avoid direct water
contact on motor
Clean with pressure-washer at 1500-2000 PSI.
Hot water, fan spray setting.
Run the machine for 15 minutes
aer washing. Allowing components to dry.
Clean the length of the Cutting Reel and
Shroud of all debris.
For optimal performance and life, the components must be cleaned every 2 to 3 days of use.
For optimal performance and life, the BLADES and the MAGNET BARS must be removed and cleaned every few hours of operation.
IMPORTANT NOTE: Your bed bar blade has been factory set to cut perfectly. Please do not alter the settings of your machine.
You might notice slight contact between your rotating cutting reel and the flat bed bar blade - this is normal.
Remove BLADE
then MAGNET BAR
carefully!
Clean BLADE and MAGNET
BAR with a utility knife.
Wipe clean with acetone.
BLADE
BLADE REMOVAL
CLEANING THE ORIGINAL & SILVER BULLET
For optimal performance and life, the components must be cleaned every 3 to 4 days of use.
Clean the Brush using
pressure washer
Clean the length of the
CUTTING REEL and
SHROUD of
all debris
Avoid
water
on the
Clean with pressure-washer at 1500-2000 PSI.
Hot water, fan spray setting.
Run the Original or Silver Bullet for 15 minutes
after washing. Allowing components to dry.

For more information or to watch our video tutorials visit cprosolutions.com 11
LEAF COLLECTOR CLEANING
(Reverse Thread)

cprosolutions. 1 855 535 0558
12
MACHINE MAINTENANCE
The Original & Silver Bullet are precision machines. It is essential that it is operated and maintained with
this in mind. The machine has been adjusted and tested by the manufacturer prior to shipping to ensure
optimal performance. However, it is important to inspect the machine at initial start-up and after each
use to ensure that no damage or plant material build-up has occurred and that the blades spin freely.
In addition, it is highly recommended to clean the machine at the end of every use. This ensures that the
blades are kept lubricated and that resin does not build-up and affect performance. This is especially
important if the machine has been stored for an extended period of time.
Due to the Quantanium coating on the tumbler, The Original & Silver Bullet do not require any
lubricants or sprays. The application of which will only damage or alter the final product and will not
assist with the cutting process. In fact, it may hinder it. Cold water is recommended to spray on blades
during harvest.
We recommend taking one or two links out of the belt after 50 hours of use. If you notice the tumbler
rotation slowing down, then this is a sign of the belt becoming loose. Once you notice this happening,
please remove a link or two until it is tight again.

For more information or to watch our video tutorials visit cprosolutions.com 13
QUANTANIUM COATED NON-STICK TUMBLER
WHAT IS QUANTANIUM?
Quantanium is a multi-coat non-stick
coating that incorporates a unique
mix of titanium particles. These
particles are blended into the coating
that stands up to almost anything
and makes the tumbler resistant to
scratching. The outstanding release is
provided by silicone, not PTFE. All of
our Quantanium coated tumblers are
made without PTFE/PFOA.
WHY DO WE USE QUANTANIUM?
Higher Potency Harvest
The non-stick properties of the Quantanium tumbler prevents precious trichomes from adhering the tumbler
surface without the need for sprays. This results in the end product having a better visual appearance while
maintaining its strong natural aroma and flavors. Overall, this results in a better-quality end product as the
natural properties are preserved during the harvesting and trimming processes.
Save Time = Save Money
Another benefit of the Quantanium tumbler is that it speeds up the harvesting process since no downtime
is required to stop and clean the tumblers throughout the day. A simple whip down with a cloth and warm
water will remove the small amount of residue that may be present.
HOW TO CLEAN THE QUANTANIUM TUMBLER
When cleaning the Quantanium tumbler, we recommend that you DO NOT pressure wash it. This will
cause the coating to flake and come off. Treat the tumbler the same way you would treat a non-stick pan at
home by letting it soak in warm, soapy water. After letting it soak, rinse the tumbler and then wipe it with a
soft, clean cloth.
In extreme cases, residue can be removed by a thorough cleaning with 3 TBSP of vinegar, 1 TBSP liquid dish
detergent and 1 cup of water. Apply with sponge or plastic scrubbing pad, then completely rinse with warm
water.
DO NOT use automotive degreasers.
While the Quantanium surface is designed to stand up to rough treatment, non-stick surfaces last longer if
you are careful not to rub or touch them with metal surfaces or sharp objects. Remember that sensible care
of your Quantanium tumbler will ensure it lasts for many years.

cprosolutions. 1 855 535 0558
14
CenturionPro Solutions (the manufacturer) will repair or replace,
without charge, any parts proven defective in material or
workmanship for a period of 10 years on the Trimming Machine
and 3 years on the Leaf Collector.
The warranty period will begin on the date the machine(s) is
purchased by the initial purchaser. Product or component
warranty defects can be remedied at any authorized service
dealer, or directly at the manufacturer. Any service work
performed, and deemed valid due to a defective part, will be free
of charge. CenturionPro Solutions reserves the right to use any
manufacturer-approved replacement part for the warranty repair.
If warranty repair is required, please contact the manufacturer at
1-855-535-0558 or
[email protected] and provide the following
information:
1. Model and serial number
2. Proof of purchase date
3. A copy of the original Warranty Registration Card or Online
Submission
4. Details of the defect or problem (include photos and videos)
The machine or defective part then must be returned to the
manufacturer for analysis or replacement at the cost of the owner.
Parts deemed to be covered under the warranty will be provided
for free excluding shipping costs.
Do not return the machine to the place of purchase for repair
or warranty claims, unless you have been authorized by
CenturionPro Solutions to do so. The place of purchase can only
sell replacement parts and will not repair any warranty issues,
unless it is noted as an authorized repair dealer and has been
authorized to work on your machine.
You may be denied warranty coverage if your machine has failed
due to any of the following:
The manufacturer assumes no risk and shall be subject to no
liability for damages or loss resulting from the specific use or
application made of the product. In no event will the manufacturer
be liable for any special, incidental or consequential damages
(including loss of use, loss of profit and claims of third parties)
however caused - whether by negligence of the manufacturer
or otherwise. If you have any questions regarding your warranty
rights and responsibilities, please contact the manufacturer.
CenturionPro trimming machines are intended for use on legal
aromatic herbs and hops. Please check all municipal, provincial/
state and federal laws and regulations before using these
machines. CenturionPro Solutions does not promote or condone
the use of these products in any way that may be deemed illegal.
Allow only persons who understand this disclaimer to operate the
machines.
• Product abuse
• Product neglect
• Improper maintenance
• Improper electrical connection
• Normal wear
• Accidental damage
• Unapproved modifications
YOU MUST REGISTER YOUR TRIMMER WITHIN 30 DAYS OF YOUR PURCHASE
WARRANTY
!! IMPORTANT !!
You have just made a smart decision by purchasing the best trimmer in the world. Failure to register your machine within 30
days of purchase will void your 10 year warranty. Protect your investment. This process will only take 3 minutes to complete.
TO REGISTER GO TO:
cprosolutions.com/warranty
WARRANTY TERMS & CONDITIONS

For more information or to watch our video tutorials visit cprosolutions.com 15
FREQUENTLY ASKED QUESTIONS
HOW EASY IS IT TO CLEAN?
Our machines can be taken apart and cleaned within 10-15 minutes. There are four screws to remove the top cover, pressure
wash the machine and then you’re good to go. Our Quantanium coating is similar to a Teflon pan you would have at home
which is even easier to clean. Just submerge in warm water, let soak and then wipe with a soft cloth. We recommend to clean
every 4-6 hours of use, but it depends on your strain. We know the importance of down time during a harvest so we wanted
to make this process extremely quick and easy.
WHAT IS THE MAINTENANCE LIKE?
We have 15 video tutorials on our website with how to fully service your machine. These step by step videos make it very
easy to do everything that will be necessary to maintaining your machine. All parts can be ordered right through the website
and will be delivered to you within days.
DO YOUR MACHINES TRIM WET OR DRY?
All CenturionPro trimming machines now come all inclusive with both wet and dry tumblers. You have a wet tumbler for wet
trimming and a dry tumbler for dry trimming. This is a major benefit because you can purchase one machine and still have
the capability to trim wet or dry flowers. Our dry tumblers have a smaller cutting surface than the wet. If you were to run dry
product through a wet tumbler, you would have excess loss of flowers. Keeping the yield high is the biggest advantage to
having a specific tumbler for both methods of harvesting, wet or dry.
ARE YOUR MACHINES BUILT TO AN INDUSTRIAL STANDARD?
We do not compromise quality for cost savings. All CenturionPro Solutions machines are composed of the highest quality
materials available in North America and each machine is put through a comprehensive quality control inspection. We only
use brand name components in the build out of our machines which enables us to have the comfort in giving you a 10 year
warranty. With proper maintenance these machines will last you well over a decade.
WHAT IS THE OPTIMAL ROOM TEMPERATURE TO TRIM?
Use your CenturtionPro machine in 50-60 °F (10- 15 °C) room to get the best performance. Cooler temperatures prevent
excessive sticking to machine components.
MY MACHINE IS NOT WORKING LIKE IT DID WHEN IT WAS NEW, WHY?
Make sure to fully clean the machine and blades. If the machine is clean, the blade is adjusted properly and the leaf collector
has full suction, then you machine should trim exactly like it was new.
MY PRODUCT IS NOT MOVING THROUGH THE TUMBLER, WHY?
You need to consistently feed the tumbler so it is about 50%-60% full at all times. If the product won’t pass through, try tak-
ing the plastic top cover off and you should instantly see it begin exiting the tumbler. You can also prop the back wheels up a
bit to increase the angle the machine is on. Some strains are heavier and will need more of an angle to exit.
WHY IS MY PRODUCT STICKING TO THE INSIDE OF THE TUMBLER?
If you find that product is sticking to the inside of the tumbler, first clean the tumbler. When you reassemble it, make sure the
top brush bristles are poking through 1/4" into the tumbler.
HOW MUCH PRODUCT SHOULD BE IN THE TUMBLER AT ONE TIME?
The tumbler should be 50-60% full when trimming.

cprosolutions. 1 855 535 0558
16
ADDITIONAL ASSISTANCE
You are about to enjoy the experience of CenturionPro Solution’s automated trimming machine.
For critical information on assembly, cleaning, care, maintenance and how to operate your machine
correctly, please review this manual and check out our video tutorials, which are posted on our website
for your ease and convenience.
Go to www.cprosolutions.com/video-tutorials for our video tutorials.
These tutorials provide how-to assistance on the following aspects of machine maintenance:
If for some reason you can’t find an answer to your question online or in your manual, please do not
hesitate to contact us.
We are open Monday through Friday from 9AM to 5PM PST.
Phone: [phone]
Filling out the “Contact Us” form on the website, is another sure way to get in touch.
• Straightening the Tumbler/Drum
• Skirt Assembly
• Removing and Replacing The Belt
• Replacing The Motor
• Blade Removal and Cleaning
• Complete Unit Assembly
• Replacing the Bearings
• Bucking Your Product
• Trimmer Cleaning and Maintenance
• Replacing The Tumbler/Drum Ring
• Sharpening The Blade
• Cleaning The Blower
• Adjusting The Blade
• Packing The Bearings
• Replacing The Pulleys

For more information or to watch our video tutorials visit cprosolutions.com 17
ORIGINAL & SILVER BULLET MACHINE AND
LEAF COLLECTOR SPECIFICATIONS
ORIGINAL & SILVER BULLET TRIMMER
Input Voltage 7 Amp - 110V NA
3.5 Amp - 220V EU/AUS
Dimensions 30" L x 13" W x 28" H
Weight 90 lbs
Reels 1
Blades Per Reel 11
Cuts Per Minute 37,500
Tumbler Diameter 6.5”
Number of Tumblers x1
Human Trimmer Replacement 20 people
Processing Capacity Dry: 16-20 lbs/hr
Wet: 80-100 lbs/hr
Warranty 10 year
ORIGINAL & SILVER BULLET LEAF COLLECTOR
Input Voltage 15Amp - 220V NA/ EU/
AUS
Dimensions 18.5" L x 20" W x 20" H
Weight 70 lbs
Horsepower 3 hp
Airflow Capacity 2750 CFM
Warranty 3 year

cprosolutions. 1 855 535 0558
18
TRIMMING DRY? HERE ARE SOME IMPORTANT TIPS!
Thank you for purchasing your DRY tumbler Centurion machine. Below is some helpful information and tips
which will ensure that you produce the best possible product and results when using the DRY trimmer:
Begin by hanging the entire plant, leaving the leaf on. Starting with 30% humidity at 60-65 degrees
Fahrenheit for 24 hours, raising the humidity to 50-60% for another five to six days. Next, carefully cut all
your flowers off the main stocks of the plant, leaving only flowers and leaves in tact. Then, depending on the
density of the flowers, it should be ready to run through the machine.
The buds should be about 80-90% dry, which allow the fan leaf and sugar leaf to remain somewhat
PLIABLE/BENDY, in a soft and flexible state. If the larger leaf is too dry and brittle (which makes it more
difficult for the machine to pull this stiffer leaf through the slots of the drum, preventing a clean, sharp cut)
raise the humidity up to 75% for about half a day to a full day. This, remarkably, softens up the unwanted leaf
while returning almost no additional moisture to the main body of the buds.
It is CRITICAL for the unwanted leaves to be soft and bendy for this machine to preform a clean perfect
cut. We also recommend using a humidifier or a water bottle with a misting nozzle to re-introduce a small
amount of moisture to the unwanted leaves before running the flowers through the machine.
The leaves MUST be SOFT and PLIABLE for the dry trimmer to be EFFECTIVE.
Please note that this method will allow virtually no additional moisture back to the inner bud/flower. The
moisture will only soften up the outer leaves.
After running the buds through the machine the chances are they are ready to bag up!
All that might be necessary is a quick test after the bag has been sealed by opening it back up to air them out
a bit to achieve the perfect moisture content (curing process).
You may prefer to run the machine with the plastic cover off, and diverter almost open (this varies depending
on the density of the strain). Please note the machine operates best when the tumbler is 40-50% full.
A huge bonus to the DRY trimming method is that the machine will require almost no periodic cleaning, as
the Quantanium non-stick drum and blade will not gum up and therefore not reduce performance.
The main advantage of DRY trimming is said to be better preservation of all the strong natural aromas and
flavours after the harvesting process is complete.
Months of work can be ruined in a few hours at the end so please be patient and take your time with the
harvesting and curing process.

For more information or to watch our video tutorials visit cprosolutions.com 19
TRIM BOTH WET AND DRY
CENTURIONPRO REGULAR WET TUMBLER
All CenturionPro Trimming Machines Now Come All Inclusive with BOTH WET and DRY tumblers!!!
CENTURIONPRO NARROW DRY TUMBLER
WHY NOT USE A DUAL-PURPOSE STANDARD TUMBLER TO TRIM BOTH WET AND DRY FLOWERS?
The solid steel slats on our wet tumblers are 1/8” in width
compared to 1/4” on tumblers offered by our competitors.
Having a thinner slat means less metal material and more
open area, resulting in an overall increase in access to the
blades by 50% when compared to the 1/4” wide standard
dual-purpose tumbler.
This increased cutting surface allows more of the flower to
come in contact with the blades resulting in a tighter, closer,
faster cut with just one pass. This negates the need for a
second pass through a tumbler or placing machines “back-
to-back”. Less tumbler travel time means less agitation and
better quality results!!
Another advantage to 1/8” wide slats is that the thinner slats
have a smaller surface area for resin to build up on, therefore
reducing resin loss and quickening tumbler clean up time.
What does this mean??? You will have a higher potency
product and less cleaning time when using our
dedicated wet tumbler.
When fresh wet flowers are fully dried, they shrink to about
25%-30% in size of what they once were. They become
brittle, fragile and more susceptible to damage.
For this reason, a Dry tumbler is needed when harvesting
dry flowers because the cutting surface area is greatly
reduced on the dry tumbler. The 1/4” wide steel slats
means more metal material is present and there is less
open area, thereby protecting the smaller fragile flowers
from being overexposed to the blades of the machine.
This will result in less trichome loss and a higher yield as
more of your flowers will stay intact during the harvesting
process.
You will not get this level of protection when using a
"dual-purpose standard tumbler" to trim both wet and dry
flowers.
Yes, a “dual-purpose standard tumbler” will harvest both wet and dry flower.
But.....You will not receive the same level of efficiency as using a tumbler
designed specifically for a particular wet or dry trimming application.
The dual-purpose standard tumbler will not trim as fast or as clean as a dedicated
wet tumbler and will not be as delicate on your flowers as a true dedicated dry tumbler.
This is why we will not promote "dual-purpose standard" tumblers and this is also why CenturionPro
includes both a wet and a dry tumbler with each machine.

cprosolutions. 1 855 535 0558
20
TROUBLESHOOTING
1) There is a high-speed ticking sound coming from the blades
This is normal. The ticking sounds are the blades making slight contact. If the machine is producing a louder
than usual ticking/banging sound, then turn off the machine and inspect the blades. Ensure your blades are
properly adjusted by following our video tutorial “Adjusting the Bed Bar Blade”
2) My product is not exiting out of the tumbler
The tumbler should always be 50%-60% full. You should be feeding the tumbler every 30-45 seconds, this
will ensure that new product entering the machine will help push out product that is trimmed. You can also
increase the downward slope of the machine. To do this place a piece of cardboard underneath the input
side wheels. You may also remove the plastic lid to help increase output.
3) My leaf collector is not turning on
Ensure the correct voltage is being supplied as per your manual and never use an extension cord longer than
25 ft. Also, test your electrical current to make sure it is producing power. If it is, then your leaf collector’s
electrical box may need to be replaced.
4) My tumbler is spinning slower than usual or is not spinning
You will need to take a link (or two) out of the belt. Use a pair of needle nose plyers to help you with this.
When putting your tightened belt back on your machine it might be a little difficult. Use the video tutorial
“Removing and Replacing the Belt” to help you with this. Once the belt is tightened properly, the tumbler
speed will resume back to normal. Ensure that the tumbler is placed correctly in the grooves and there is no
lubricant on the Tumbler O Rings.
5) The leaf collector suction seems weak
Ensure that nothing is blocking the inlet or outlet on the leaf collector. Try cleaning your bags as this will keep
the suction performance high. Build up that occurs in the leaf collector around the impeller can cause the
suction to become weak as well. Unplug the leaf collector and follow cleaning instructions.