Challenger SL04B User manual

SL04B Instructions Rev01
MODEL: SL04B
We are delighted that you have purchased this PIR Light. This light
is suitable for indoor or outdoor use. Please read this instruction
manual before installation and retain for future reference.
IMPORTANT: Never modify the unit, there are no user serviceable
parts inside. Not suitable for use with dimmer switches. Install in
accordance with IEC Wiring Regulations.
THE LIGHT SHOULD BE INSTALLED BY A QUALIFIED
ELECTRICIAN.
OCCUPANCY
The PIR Sensor has an Occupancy Range of Radius 3 meters. In this
range, the sensor will detect small movement.
If you want to achieve best results, we suggest you take into account the
following points:
1. The OccupancyRange is 3 meters.
2. We suggest the delay time must be set more than 10 minutes.
3. The PIR Sensor must worked at 25˚c or lower and dry weather
(normal temperature)
POSITIONING THE LIGHT
When selecting the mounting position, take into account the
following points:
1. The sensor is designed for optimum performance when mounted at a
height of between 1.8.5 to 2.5 meters (see Figure 1)
2. Avoid pointing at or positioning close to heat sources such as heaters
or heat extraction units, which may cause false triggering.
3. Avoid pointing at bright lights as the PIR sensor will not function when
you set Lux control level to dark (position).
4. Avoid mounting at strong electromagnetic disturbance, i.e. near
electrical motor or fluorescent lamp ballast.
INSTALLING THE LIGHT
Before commencing any electrical work, ensure the mains supply is
isolated by switching off and removing the relevant fuse. (See Figure
2 A ,B and C)
A.B. Wall and Ceiling Mounting(Figure 2A and B)
1. Usea screwdriverto remove the bottom
2. Remove the Junction Box and Terminal Block
3. Use the Bottom Cover to mark the position of screw holes onto
mounting surface. Drill the wall to depth of about 35mm and fit the
plastic plugs, and then fix the Bottom Cover to the mounting surface
with rightly screws. Care should be taken to avoid drilling or screwing
into concealed electrical wiring.
Occupancy 3m
Fig.1 Detection Area
210¡ ã
1.8-2.5m
10m

SL04B Instructions Rev01
4. Connect mains wiring to the terminal block.
5. Refit the Terminal Block , Junction Box.
6. Fit the main body onto the Bottom Cover.
C. Corner Mounting(Figure 2 C)
1. Remove the bottom corner mounting support
7. Use a screwdriver to remove the bottom
2. Remove the Junction Box and Terminal Block
3. Use the corner mounting support to mark the position of screw holes
onto mounting surface. Drill the wall to depth of about 35mm and fit the
plastic plugs, and then fix the corner mounting support to the mounting
surface with rightly screws. Care should be taken to avoid drilling or
screwing into concealed electrical wiring.Connect mains wires to the
terminal block.
4. Connect mains wiringto the terminal block.
5. Refit the Terminal Block , Junction Box.
6. Fitthe Bottom Cover onto the corner mounting support
7. Fit the main body onto the Bottom Cover
Fig.2 MOUNTING
A
B
C
N
L OUT
L IN
L IN
L OUT
N
L IN
L OUT
N
Wall Mount
Ceiling Mount
Corner Mount

SL04B Instructions Rev01
Afterfinishing the installation operation, youcan adjust the working stateof
the PIR SENSOR
ADJUSTING THE LUX (LIGHT) CONTROL LEVEL:
The Luxcontrol is a built-in sensing device (photocell) that detectsdaylight
and darkness.
() position denotes the light can be turned on during daylight and night.
()position denotes the light can be turned only at nigh.
You can set to operate the unit at the desired level by adjusting the LUX
knob
ADJUSTING THE DURATION TIME:
The duration time is “the length of time that light switches ‘on’ after
activation. The duration time can be adjusted from (10±5) seconds to
(40±5) minutes. Rotating the TIME knob from (+) to (-) will reduce the
duration time. Note: Once the light has been triggered by the PIR sensor
any subsequent detection will start the timed period again from the
beginning.
ADJUSTING THE SENSITIVITY: The sensitivity means the Maximum
distance which PIR Sensor can be triggered by movement body. Turning
the SENS knob from (+) to (-) will decrease the sensitivity.
SETTING THE CONTROLS
1. Put the Lux control knob to light () position, turn the wall switch on
and wait half a minute for the control circuit to stabilize. At this stage
ensure that the TIME control knob is set at minimum duration time (-)
position. The floodlight will now switch on and remain on for about 30
seconds (within 60 seconds).
2. Direct the sensor toward the desired area to be scanned by adjusting
the swiveljointonthe sensor arm.
Important: loosen the lock nuts and screws on sensor and floodlight
before making any adjustments.
3. Have another person move across the center of the area to be
scanned and slowly adjust the angle of the sensor arm until the unit
sensors the presence of the moving person, causing the floodlight to
switch on.
4. Adjust time controlto required setting.
To set the light levelat which the floodlight will automatically switch “on” at
night, turn the LUX control knob from daylight () to night (). If the
floodlight is required to switch on earlier, e. g. Dusk, wait for the desired
lightlevel,andthenslowlyturntheLUXcontrolknobtowardsdaylight while
someone walks across the center of the area to be detected. When the
floodlight switches on, release the LUX control knob. You may need to
make further adjustments to achieve your ideal light level setting
Fig.3 Knob

SL04B Instructions Rev01
TECHNICAL DETAILS:
Voltage: 230 V~ 50 Hz
Wattage: Max. 2000Watt~ incandescent bulb (Resistive-Load)
Detection range: 210°Max. 10meters radius for normal detection
Max. 3meters radius for occupancy detection
Delay time: From (10±5) seconds to (10±2) minutes adjustable
Lux control level: Daylight to Night adjustable
Due to our policy of continuous improvement we reserve the right to change specification
without prior notice.
Errors and omissions excepted. These instructions have been carefully checked prior to
publication. However, no responsibility can be accepted by Challenger Security Products
for anymisinterpretation of these instructions.
CHALLENGER SECURITY PRODUCTS
10 Sandersons Way, Marton,
Blackpool, FY4 4NB
Tel :[phone] Fax:[phone]
Email: [e-mail]
Website: www.challenger.co.uk