Chamberlain merlin MR800a User manual

professional
Installation and operating
instructions
odel R800a / R600a
www.chamberlainanz.com

1
The Protector System must be used for all
installations where the closing force as measured
on the bottom of the door is over 400N (40kgf).
Excessive force will interfere with the proper operation
of the Safety Reverse System or damage the garage
door.
After installation, ensure that the parts of the door
do not extend over public footpaths or roads.
Disengage all existing garage door locks to avoid
damage to garage door.
nstall the wireless wall control (or any additional wall
control) in a location where the garage door is
visible, at a height of at least 1.5m and out of the
reach of children. The appliance is not intended for
use by young children or infirm persons without
supervision. Serious personal injury from a closing
garage door may result from misuse of the opener.
Permanently fasten the Warning Label adjacent to the
wall control as a reminder of safe operating procedures.
Activate opener only when the door is in full view,
free of obstructions and the opener is properly
adjusted. No one should enter or leave the garage
while the door is in motion.
Do not allow children to play near the door.
Disconnect electric power to the garage door
opener before making repairs or removing covers.
SAVE THESE INSTRUCTIONS
WARNING: Failure to comply with the following instructions may result in serious personal injury or property damage.
• Read these instructions carefully and follow ALL instructions carefully
• The garage door opener is designed and tested to offer reasonable safe service provided it is installed and
operated in strict accordance with the instructions in this manual.
These safety alert symbols mean
WARNING – a personal safety or property damage instruction.
Read these instructions carefully.
Warning: If your garage has no service entrance door, a 1702A L outside quick release must be installed. This accessory allows
manual operation of the garage door from outside in case of power failure.
Keep garage door balanced .Do not let the garage
door opener compensate for a binding or sticking
garage door. Sticking or binding doors must be
repaired. Garage doors, door springs, brackets and
their hardware are under extreme tension and can
cause serious personal injury.
Do not wear rings, watches or loose clothing while
installing or servicing a garage door opener.
To avoid serious personal injury from entanglement,
remove all ropes, chains and locks connected to
the garage door before installing the door opener.
nstallation and wiring must be in compliance with your
local building and electrical codes.
The safety reverse system test is very important.
Your garage door UST reverse on contact with a
40mm obstacle placed on the floor. Failure to properly
adjust the opener may result in serious personal injury
from a closing garage door. Repeat the test once a
month and make any necessary adjustments.
This opener should not be installed in a damp or
wet space.
Take care when operating the manual release as an
open door may fall rapidly due to weak or broken
springs, or being out of balance.
The drive must not be used on a wicket door (door
within a door)
Start by Reading These mportant Safety nstructions
Tools Required
2
1. Ladder (or similar device to safely support door weight)
2. Adjustable wrench for U-bolts already installed on the
door
3. 8mm socket, 10mm socket and 13mm extended socket
and socket wrench
4. 12inch socket extension (for minimum side-room
installations)
5. Drill and 5.5mm drill bit
6. Philip's head screw driver
7. Marker Pen
Carton Inventory
1
8
1. nstruction manual (this document)
2. Stop bracket collar
3. Clamp bracket
4. Release handle and cord
5. C945 remote control (2)
6. CM128 wireless wall control (MR800a)
7. Weight bar
8. Bracket plate
9. Hardware bag

2
Preparing The Door
4
weight bar
stop bracket collar
Disable all locks and remove any ropes connected to
the garage door.
Complete the following test to ensure your door is well
balance, and not sticking or binding:
• Lift the door to about halfway and then release it. The
door should remain suspended entirely by its spring.
• Raise and lower the door to discover if there are any
sticking or binding points.
• f your door spring does not hold the door in place or the
door binds or sticks, call a qualified door technician before
automating the door.
• nstall stop bracket collar on the opposite end to where
the opener is to be installed. Fit the stop bracket hard
against the boss of the door drum. Ensure the U-bolt
holding the door shaft to the door bracket is tightly
secured.
Installing the weight bar
• Place the weight in the centre of the door. Use a Pencil to
mark the two hole positions.
• Drill two 5.5mm through the two marked position, then
place the weight bar inside.
• Use the 5mm bolts, washers and nuts to fasten the weight
bar in place.
R800a
Max door height 4.5m
Max curtain area 14.5m sq
with Protector 16.5m sq*
*The Protector System™ (Safety Beams) must be
installed if the force at the edge of the closing door
force exceeds 400N (40kgf).
Door shaft diameter must not exceed 35mm.
R600a
Max door height 3.5m
Max curtain area 12.5m sq
with Protector 14.5m sq*
*The Protector System™ (Safety Beams) must be
installed if the force at the edge of the closing door
force exceeds 400N (40kgf).
Door shaft diameter must not exceed 35mm.
Door Requirements
3
Ensure that there is at least 45mm from the edge of the curtain to the edge of the bracket. f the roller door drums
are on the edge of the curtain or are of small diameter additional clearance may be required.
If the drums are more than 60mm from the curtain edge or of small diameter extension poles may be
required.
Different drum and bracket types may result in the minimum side room clearance not being possible and
extension poles being required. Ensure there is a power point near the opener.
Typical side room installation inimum side room installation

3
Preparing the Opener
5
For left hand side installations
the wire jumper should be removed.
Place the Opener in anual Release mode.
Disengage:
• Pull the release cord down once until you hear a
clicking sound. The operator is now in manual
mode and may be opened or closed.
Engage:
To re-engage the opener, pull the release cord
down until you hear a clicking sound, the motor is
now ready for operation.
NB: The drive forks may now be positioned
into the drum as required.
For right hand side installations
the wire jumper should be in place
(factory installed).
Set Opener Position (Left or Right hand)
Attaching the Extension Poles (if required)
• nsert the extension poles into the gear
• Align the extension pole holes with the gear holes
• Using the supplied screws secure the extension poles.

4
Installation steps
6
FOR RIGHT HAND INSTALLATIONS
(REFER SECTION 5, page 3)
•Ensure that the opener position jumper (wire connector) is installed
(refer section 5, page 3).
• Place the opener in manual release mode (refer section 5, page 3).
• Open the roller door fully. For safety, tie a rope around the door.
• Ensure that the U-bolt on the left hand side of the door is secure.
• Mark the position of the door shaft on the right hand door bracket.
• Carefully remove the U-bolt on the right hand side, checking that
the spring tension inside the roller door is not being released.
• You will need assistance for the following steps. Slide or lift the
door shaft clear of the door bracket supporting the door weight
with a ladder or similar device. Then slip the opener over the shaft.
• The forks should engage either side of the support spoke.
• Typical installation: Place the door shaft back onto the door bracket
in the position that it was originally. Clamp the opener
to the door shaft with the supplied bracket plate, 8mm bolts and
nuts. Tighten sufficiently to fasten the opener firmly to the shaft i.e.
25Nm- 28Nm. Replace U-bolt and secure firmly.
inimum side room installation: Place the opener and door shaft
onto the door bracket in the position that the door shaft was
originally. Clamp the opener to the door shaft though the door
bracket with the supplied bracket plate, 8mm bolts and nuts.
Tighten sufficiently to fasten the opener firmly to the shaft i.e.
25Nm-28Nm.
• Remove any ropes used.
• Plug opener into nearby power point and switch on power point,
opener lights should now turn on.
FOR LEFT HAND INSTALLATIONS
(REFER SECTION 5, page 3)
•Ensure that the opener position jumper (wire connector) is removed
(refer section 5, page 3).
• Place the opener in manual release mode (refer section 5, page 3).
• Open the roller door fully. For safety, tie a rope around the door.
• Ensure that the U-bolt on the left hand side of the door is secure.
• Mark the position of the door shaft on the right hand door bracket.
• Carefully remove the U-bolt on the right hand side, checking that
the spring tension inside the roller door is not being released.
• You will need assistance for the following steps. Slide or lift the
door shaft clear of the door bracket supporting the door weight
with a ladder or similar device. Then slip the opener over the shaft.
• The forks should engage either side of the support spoke.
• Typical installation: Place the door shaft back onto the door bracket
in the position that it was originally. Clamp the opener
to the door shaft with the supplied bracket plate, 8mm bolts and
nuts. Tighten sufficiently to fasten the opener firmly to the shaft i.e.
25Nm- 28Nm. Replace U-bolt and secure firmly.
inimum side room installation: Place the opener and door shaft
onto the door bracket in the position that the door shaft was
originally. Clamp the opener to the door shaft though the door
bracket with the supplied bracket plate, 8mm bolts and nuts.
Tighten sufficiently to fasten the opener firmly to the shaft i.e.
25Nm-28Nm.
• Remove any ropes used.
• Plug opener into nearby power point and switch on power point,
opener lights should now turn on.

Pinning the Door
9
Use bolts or pop-rivets (not supplied) to hold the curtain
to the door drum.
• Disengage the operator (see point 8 above) and close the
door manually. Re-enaged motor but pulling down on the
release cord.
• Try to manually open the door with the opener engaged. Any
excess door curtain may balloon out from the top of the
drum.
• To remedy any ballooning place gutter-bolts or pop rivets (not
supplied) 75mm up from where the curtain leaves the roll.
Secure these through the curtain into the drum wheel at each
end of the curtain.
Free curtain Ballooning Add fasteners here
Door closed Door can be
lifted Door secure
Attach the Release Handle and Cord
7
•Thread one end of the rope through the hole in the top
of the red handle so “NOT CE” reads right side up as
shown.
Secure with an overhand knot at least 25mm from the
end of the rope to prevent slipping.
• Thread the other end of the rope through the loop of the
manual release cable.
• Adjust rope length so the handle is no higher than 1.8m
above the floor. Secure with an overhand knot. f the
door is greater than 2.5m in height the Release Cord
Extension kit accessory is required.
NOTE: f it is necessary to cut the rope, heat seal the cut
end with a match or lighter to prevent unraveling.
5
Operating the anual Release
8
Take care when operating the manual
release as an open door may fall rapidly due
to weak or broken springs, or being out of
balance.
Disengage:
• Pull the release cord down once until you hear a
clicking sound. The door is now in manual mode and
may be opened or closed.
Engage:
To re-engage the opener, pull the release cord down
until you hear a clicking sound, the motor is now ready
for operation.

6
1423
anual Limit setting
With the door in the midway position.
• Press and hold the BLACK button until the orange
LED starts flashing.
• Use the BLACK (up) and PURPLE (down) button to
set the door opening limit
• Press the Green activation button to start the door,
once it starts travelling down, press either the
BLACK or PURPLE button to engage manual limit
setting.
•Use the PURPLE and BLACK buttons to set
the closing limit.
• Test door three or four times to check limit settings.
Setting the Limits
Up limits regulate the points at which the door
will stop when moving up or down. Follow the
steps below to set the limits.
• Check that the opener is engaged and midway
between open and closed.
To program the travel limits:
• Press and hold the BLACK button (3) until the
orange indicator light (2) starts flashing slowly and
then release. Opener lights will dim. Press the
BLACK button to move the door UP or the PURPLE
down button to move the door DOWN until the door
reaches the desired UP limit.
Check to be sure the door is high enough for your
vehicle. Adjust if necessary.
• Press the GREEN start button (4). This sets the full
UP limit. The door will travel to the floor and reverse
back to the UP limit. The opener has learned its
limits.
• The indicator light (2) will stop flashing when the
limits have been learned.
NOTE: f the door presses excessively on the floor or
reverses before it reaches the floor use the Manual
Limit setting option:
11
Program your Opener & Remote
Please note your remote controls and wall plate
( R800a) have already been programmed into
your operator.
Activate the opener only when door is in full view,
free of obstruction and properly adjusted. No one
should enter or leave garage whilst door is in
motion. Do not allow children to operate push
button(s) or remote(s). Do not allow children to
play near the door.
Fix any wall control at a height of at least 1.5m and
within sight of the door but away from any moving
parts.
• Fix the warning against entrapment label near the
wall control.
ADDING remotes using the PURPLE “LEARN”
Button
• Press and release the PURPLE “LEARN” button on
the opener. The orange indicator light will glow
steadily for 30 seconds.
• Within 30 seconds, press and hold the desired button
on the wireless wall control or remote control that you
wish to operate your garage door.
• Release the button when the opener light blinks. t
has learned the code.
DELETE all Remote Control Codes
Please note this deletes all remotes and codes
Press and hold the PURPLE LEARN button until the
orange indicator light goes out (approximately 9
sec).
10
The force must be learned in order to properly
complete the setting of the limits.

7
Setting the Force
The force, as measured on the closing edge of the door,
should not exceed 400N (40kgf). f the closing force is
measured to more than 400N, the Protector System must
be installed. See section 14.
The force setting regulates the amount of power
required
to open and close the door.
• Press the PURPLE button (1) twice to enter opener into
Force Adjustment Mode. The indicator light (2) will flash
quickly.
• Press the GREEN start button (4) on the bottom of the
opener. The door will travel to the DOWN limit. Press
the GREEN start button (4) again, the door will travel to
the UP limit. Press the GREEN start button (4) again to
complete the travel cycle. The indicator light (2) will stop
flashing when the force has been learned.
• The door must travel through a complete cycle, UP and
DOWN, in order for the force to be set properly. f the
opener cannot open and close your door fully, inspect
your door to insure that it is balanced properly and is not
sticking or binding.
12
Testing the Safety Reverse System
The safety reverse system test is important. The
garage door must reverse on contact with a 40mm
obstacle laid flat on the floor. Failure to properly
adjust the opener may result in serious personal
injury from a closing garage door. Operate the door in
the down direction. The door must reverse on the
obstruction. f the door stops on the obstruction, remove
obstruction and repeat limit and force setting, sections 11
& 12, pages 6 & 7. Repeat test.
13
Install the Protector System™
(Safety Beams)
Install this accessory for all installations where the
closing force as measured on the bottom of the
door is over 400N (40kgf).
After opener has been installed and adjusted, The
Protector System™ accessory can be installed.
nstructions are included with this accessory.
The Protector System™ provides an additional
measure of safety against a small child being
caught under a garage door. t uses an infra-red
beam which, when broken by an obstruction, causes a
closing door to open and prevents an open door from
closing and is
strongly recommended for home-
owners with young children.
Note: The opener will automatically detect the
protector system when it is installed and operating for
5 minutes (during this time the beams must remain
unobstructed). The opener will not close unless the
sensors are aligned.
14
12
142
(2x)

CARE OF YOUR OPENER
When properly installed, your opener will provide high performance with a minimum of maintenance. The opener
does not require additional lubrication. Limit and Force Settings: These settings must be checked and properly set
when the opener is installed. Weather conditions may cause some minor changes in the door operation, requiring
some re-adjustments, particularly during the first year of operation. Refer to limit and force setting in, sections 11
& 12, pages 6 & 7. Follow the instructions carefully and repeat the safety reverse test after any adjustment.
Remote Control: Additional remotes can be purchased at any time. Refer to Accessories. Any new remotes must
be programmed into the opener. Remote Control Battery: The lithium batteries should produce power for up to 5
years. f transmission range decreases, replace the battery .
Optional features
• Motion Detecting Control Panel
Connect white/red wire to the red quick connect
terminal and the white wire to the white quick
connect terminal.
• The Protector System™ (Safety Beams)
Connect both white wires to the white quick connect
terminal and both white/black wires to the grey quick
connect terminal.
• Flashing light connection.
Connect wires intot he Flashing light input and then
position the flashing light where required.
Standby power: To access the Standby power unit
connector,remove the knockout to the right of the start
button.
Auto Close:
Note: The Protector System (Safety Beams) must be
installed before using this function.Timer trim pot must
be set to zero when the
protector system is installed.
Timed auto close function is enabled by turning the
dial to the required time, once the beams have learnt
into the unit.
15
12345
67
89 10 11 12 13
Accessories
1. Model CM128 2-Function Wireless Wall Control
2. Model CM842 2-Function Remote Control
3. Model CM844 4-Function Remote Control
4. Model C940 Single-Function Remote Control
5. Model C943 3-Function Remote Control
6. Model C945 3-Function Mini Remote Control
7. Model C840 Keyless Entry System
8. Model C98 Motion Detecting Control Panel
9. Model 760 Outside Keylock
10. Model CM1702 Outside Quick Release
11. Model C77 The Protector System™
12. Model FLA230 Flashing Light Kit
13. Model 475 Standby power unit
16
Remove
knockout
8

Troubleshooting
1.The opener doesn't operate from either the
GREEN start button or the remote controls:
• Does the opener have electric power? Plug a lamp into
the outlet. f it doesn't light, check the fuse box.
• Have you disabled all door locks? Review installation
instruction warnings on page 1.
• s there a build-up of ice or snow under the door? The
door may be frozen to the ground. Remove any
restriction.
• The garage door spring may be broken. Have it
replaced.
2. Opener operates from the remote control, but not
from the wired wall control (optional accessory):
• s the wall control lit? f not, reverse the two wires. f the
opener runs, check for a faulty wire connection at the
wall control, a short under the staples, or a broken wire.
• Are the wiring connections correct? Refer to wired wall
control instructions.
3. The door operates from the GREEN start button
or wired wall control, but not from the wireless wall
control or remote control:
• f the wired wall control is installed and it is flashing,
ensure the Lock feature is off.
• Program the opener to match the remote control code.
(Refer to section 10, page 6.) Repeat with all remotes.
4. The remote control has short range:
• Change the location of the remote control in your car.
• Check to be sure the antenna on the bottom of the
opener extends fully downward.
• Some installations may have shorter range due to a
metal door, foil backed insulation, or metal garage
siding.
5. The garage door opens and closes by itself:
• Be sure that all remote control push buttons are off.
• f the wired wall control (optional accessory) is
installed, remove the bell wire from the wired wall
control terminals and
operate from the GREEN start button or remote control.
f this solves the problem, the wired wall control is faulty
(replace),
or there is an intermittent short on the wire between the
wired wall control and the opener.
• Clear memory and re-program all wireless wall
controls and remote controls.
6. The door reverses and stops before opening
completely:
• s something obstructing the door? s it out of balance,
or are the springs broken? Remove the obstruction or
repair the door.
7. The door reverses for no apparent reason and
opener lights blink for 5 seconds after reversing:
• Check the Protector System (safety beams), if
installed. Correct alignment if the red light on the beam
is solid.
8. The door opens but won't close or reverses while
closing:
• s something obstructing the door? Pull the manual
release handle. Operate the door manually. f it is
unbalanced or binding, call a trained door systems
technician.
• Clear any ice or snow from the garage floor area where
the door closes.
• Repeat the limit and force setting in section 11 & 12,
pages 6 & 7. Repeat safety reverse test after
adjustments.
9. The opener strains to operate door:
•The door may be out of balance or the springs may be
broken. Close the door and use the manual release to
disconnect the door. Open and close the door manually.
A properly balanced door will stay in any point of travel
while being supported entirely by its springs. f it does
not, disconnect the opener and call a trained door
systems technician.
10. The opener motor hums briefly, then won't work:
• Check that the door is not in manual release mode,
refer section 8, page 5.
• The garage door springs may be broken. See above.
• f the problem occurs on the first operation of the
opener, door may be locked. Disable any door locks.
11. The opener won't operate due to power failure:
• Use the manual release handle to disconnect the door.
The door can be opened and closed manually. When
power is restored, re-engage the opener, refer section
8, page 5.
• f a Standby power unit is connected, the opener should
be able to operate up to 20 times without power.
12. Setting the limits manually:
a. Check that the opener position jumper is correct, refer
section 5, page 3.
b. Press and hold the BLACK button until the orange
indicator light starts flashing slowly then release.
c. Press the BLACK button to move the door UP or the
PURPLE button to move the door DOWN until the door
reaches the desired UP limit. Ensuring there is enough
clearance for your vehicle.
d. Press the GREEN start button. This sets the UP limit
and begins closing the door. mmediately press either
the PURPLE or the BLACK button. The door will stop.
Adjust the desired DOWN limit using the BLACK and the
PURPLE buttons. Check to be sure the door is fully
closed without applying excessive pressure to the door
curtain. Press the GREEN start button. This sets the
DOWN limit and begins opening the door. NOTE: f
neither the BLACK or the PURPLE button is pressed, the
door will reverse off the floor and the DOWN travel limit
will be set automatically.
e. Open and close the door with the GREEN start button,
remote control or wall control 2 or 3 times.
• f the door does not stop in the desired UP limit or
reverses before the door stops at the DOWN limit.
Proceed to Setting the Force, section 12, page 7. f the
door still does not stop at the desired limits is something
obstructing the door? Disengage the opener. Open and
close the door manually. f it is unbalanced or binding,
call a trained door systems technician.
• f the door stops at both the desired UP and DOWN
limits, proceed to Setting the Force.
13. Auto close does not work:
•Check alignment of beams (LED indicators should be
solid). f setting up see section 15 page 8. To re-set auto
detect of the safety beams, turn the power off, (remove
standby power unit if installed) and set timer trim pot to
zero before re-setting power.
9

10
OPERATION OF YOUR OPENER
Your opener can be activated by any of the following
devices:
•The GREEN start button
Hold the button down until door starts to move.
•The Wall Control, Outside Keylock or Keyless
Entry System (if you have installed any of these
accessories).
•The Remote Control Transmitter or Wireless Wall
Control (8)
Hold the push button down until the door starts to move.
When the Opener is activated by Remote Control, Green
Start Button or Wall Control:
• f open, the door will close. f closed, the door will open.
• f closing, the door will stop.
• f opening, the door will stop (allowing space for entry and
exit of pets and for fresh air).
• f the door has been stopped in a partially open or closed
position, it will reverse direction.
• f an obstruction is encountered while closing, the door
will reverse.
• f an obstruction is encountered while opening, the door
will reverse and stop.
• The optional Protector System™ uses an invisible beam
which, when broken by an obstruction, causes a closing
door to open and prevents an open door from closing. t
is STRONGLY RECOMMENDED for home-owners with
young children.
Allow a 15 minute cooling period after 4 minutes of
continuous operation of the opener.
Opening the Door anually:
Door should be fully closed if possible. Weak or broken
springs could allow an open door to fall rapidly.
Property damage or serious personal injury could result.
The door can be opened manually by pulling the release
cord down see point 8 page 5.
The Opener Light Will Turn On:
• when opener is initially plugged in;
• when the power is briefly interrupted;
• when the opener is activated.
• The light turns off automatically after 2-1/2 minutes.
AINTENANCE OF YOUR OPENER
Once a onth:
• Repeat safety reverse test.
Make any necessary adjustments (see page 7)
• Manually operate door. f it is unbalanced or binding, call
for professional garage door service.
• Check to be sure door opens and closes fully.
Set Limits and/or Force if necessary.
SPECIAL NOTE: Chamberlain strongly recommends that the
protector system be installed on all garage door openers.
Specifications R800a
nput Voltage: 230-240~, 50Hz, 105W
Rated Load: 22Nm
Max.Pull Force: 550N
Max. Door Weight 100kg
Standby power: 3 watts (nominal)
DC gearmotor permanent lubrication
Max. Drum Rotations: 5
Memory Registers: 64
Operating Frequency: 433.92MHz
Specifications R600a
nput Voltage: 230-240~, 50Hz, 90W
Rated Load: 20Nm
Max.Pull Force: 500N
Max. Door Weight 80kg
Standby power: 3 watt (nominal)
Drive: DC gearmotor
permanent lubrication
Max. Drum Rotations: 5
Memory Registers: 64
Operating Frequency: 433.92MHz

114A3567 ANZ1 11
C, 2007 Chamberlainanz
Liability – Australia only
Under no circumstances shall the Seller be liable for
consequential, incidental or special damages arising in
connection with the use, or inability to use, the Unit. n no
event shall the Seller's liability for damages or injury arising
from breach of law or contract or for negligence, exceed the
cost of repairing or replacing the Unit or refunding the
purchase price of the Unit.
Under Division 2 Part V of the Trade Practices Act, 1974,
certain warranties and conditions ( mplied Terms) are implied
into contracts for the supply of goods or services if the goods
or services are of a kind ordinarily acquired for personal,
domestic or household use or consumption. Liability for
breach of those mplied Terms cannot be excluded or limited
and the limitations and exclusions above do not apply to the
mplied Terms.
Except for the mplied Terms and the warranties set out
above, the Seller excludes all warranties and conditions
implied by statute, at law, in fact or otherwise.
Liability – New Zealand only
Except as set out in the Fair Trading Act 1986 and the
Consumer Guarantees Act 1993:
(a) all other guarantees, warranties and representations in
relation to the Unit or its supply are excluded to the extent
that the Seller can lawfully exclude them; and
(b) under no circumstances shall the Seller be liable for
consequential, incidental or special damages arising in
connection with the use, or inability to use, the Unit, other
than those which were reasonably foreseeable as liable
to result from the failure.
NOTE: We request that you attach your sales docket or
invoice to this manual to enable you to establish the date of
purchase in the unlikely event of a service call being made.
Chamberlain reserves the right to change the design and
specification without prior notification. Some features or
accessories may not be available in certain markets or areas.
Please check with your distributor.
Chamberlain service centres:
Australia
Phone toll free 1800 638 234
Fax toll free 1800 888 121
New Zealand
Auckland phone [phone]
Phone toll free 0800 ERLIN
Fax toll free 0800 653 663
www.chamberlainanz.com
CHA BERLAIN 2 YEAR LI ITED WARRANTY
erlin R800A / R600A
Roller Door Operator
Chamberlain Australia Pty Limited / Chamberlain New
Zealand Limited (Seller) warrants to the original
purchaser of the erlin R800A / R600A Roller Door
Operator (Unit) that it is free from defects in material
and/or workmanship for a period of 2 YEARS from the
date of first purchase from the Seller. The R800a has an
extended warranty on the OTOR ONLY, covering the
unitʼs motor for dometic use for a period of 5 years from
date of purchase.
Please retain your proof-of-purchase in the unlikely event you
require warranty service.
f, during the limited warranty period, the Unit fails due to
defects in materials or workmanship Chamberlain will,
provided the defective part or Unit is returned freight and
insurance prepaid and well packaged to the nearest
Chamberlain office or authorised installer, undertake to repair
or, at its option, replace any defective part or Unit and return
it to the Buyer at no cost. Repairs and replacement parts are
warranted for the remaining portion of the original warranty
period.
Limited warranty on motor
Chamberlain will furnish a replacement motor free of charge,
if it is found to be defective. Labour costs may apply.
Where the Unit has been installed by an authorised installer,
Chamberlain will furnish replacement parts free of charge
through the authorised installer. A service fee for on-site
service may apply.
n-warranty service
During the warranty period, if the product appears as though
it may be defective, call our toll free service before removal of
the unit. A Chamberlain technician will diagnose the problem
and promptly supply you with the parts for “do-it-yourself”
repairs, or provide you with shipping instructions for a factory
repair or replacement. f an authorised installer installed your
unit you must call them for prompt on-site service.
f our service centre determines that a warranty claim has
been made in respect of a failure or defect arising under out
of any exclusion set out below, we may charge you a fee to
repair and/or return the Unit to you.
Exclusions
This warranty does not cover any failure of the Unit due to:
1. non-compliance with the instructions regarding installation,
operation, maintenance and testing of the Unit or of any
product with which the Unit is used.
2. any attempt to repair, dismantle, reinstall or move the
Product to another location once the Product is installed by
any person other than an authorised installer.
3. tampering, neglect, abuse, wear and tear, accident,
electrical storm, excessive use or conditions other than
normal domestic use.
This warranty does not cover any problems with, or relating to,
the garage door or garage door hardware, including but not
limited to the door springs, door rollers, door alignment or
hinges, any problems caused by electrical faults, replacement
of batteries or light bulbs or labour charges for reinstalling a
repaired or replaced Units.