Chamberlain RollerLift Plus CR855MYQ User manual

This manual containsIMPORTANT SAFETY information
DO NOT PROCEED WITH THE INSTALLATION BEFORE READING THOROUGHLY
CR855MYQ
Garage Roller Door Opener
Installation and Operating Instructions
Owners Copy: SAVE THESE INSTRUCTIONS for future reference
chamberlaindiy.com.au
chamberlaindiy.co.nz
capable

2
SAFETY INSTRUCTIONS
WARNING
• Failure to comply with the following instructions may result in serious injury or property damage.
• Read and follow all instructions carefully.
• The garage door opener is designed and tested to offer safe service provided it is installed and operated in strict
accordance with the instructions in this manual.
These safety alert symbols mean WARNING : A possible risk to personal safety or property damage exists.
Keep the garage door balanced. Do not let the garage
door opener compensate for a binding or sticking garage
door. Sticking, binding or unbalanced doors must be
repaired before installing this opener.
Do not wear rings, watches or loose clothing while
installing or servicing a garage door opener. Wear gloves
and suitable protective clothing where appropriate.
Frequently examine the door installation. In particular
examine cable, springs and mountings for signs of wear,
damage or imbalance. Do not use if repair or adjustment is
needed since springs and hardware are under extreme
tension and a fault can cause serious personal injury.
To avoid serious injury from entanglement, remove all
ropes, chains and locks connected to the garage door
before installing the door opener.
Installation and wiring must be in compliance with your
local building and electrical codes.
The safety reverse system test is very important. Your
garage door MUST reverse on contact with a 40 mm
obstacle placed on the floor. Failure to properly adjust the
opener may result in serious injury from a closing garage
door. Repeat the test once a month and make any
necessary adjustments.
This appliance should not be used by children or persons
with reduced physical, sensory or mental capablities, or a
lack of experience & knowledge, unless they have been
given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Automatic Drive - Keep away from the area of the door
as it may operate unexpectedly.
WARNING! Product includes wireless transmitters and
wall controls that contain coin/button cell batteries. Keep
wireless devices and batteries away from children. Battery
can cause severe or fatal injuries in 2 hours or less if
swallowed or placed inside any part of the body. Seek
immediate medical attention if it is suspected that a coin/
button cell battery has been swallowed or placed inside
any part of the body.
The opener must not be used on a wicket door (door
within a door).
The Protector SystemTM (IR Beams) must be used for
all installations where the closing force as measured
on the bottom of the door is over 400 N (40 kgf).
Excessive force will interfere with the proper operation of
the safety reverse system or damage the garage door.
Installers must ensure that the doors are installed in a
compliant manner as per AS/NZS 60335-2-95.
After installation, ensure that the parts of the door do
not extend over public footpaths or roads.
Install the wireless wall control (or any additional wall
control) in a location where the garage door is visible
away from moving parts, at a height of at least 1.5 m
and out of the reach of children. Do not allow children
to operate push buttons or transmitters. Serious
personal injury from a closing garage door may result from
misuse of the opener.
Permanently fasten the warning labels in prominent
places, adjacent to wall controls and manual release
mechanisms as a reminder of safe operating procedures.
Activate opener only when the door is in full view,
free of obstructions and the opener is properly
adjusted. No one should enter or leave the garage
while the door is in motion.
Do not allow children to play near the door or with
door controls.
If the power cable is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified
persons in order to avoid hazard.
Disconnect electric power to the garage door opener
before making repairs or removing covers.
This opener should not be installed in a damp or wet
space exposed to weather.
KEEP THESE INSTRUCTIONS
NOTE: If your garage has no service entrance door, we recommend an outside quick release must be installed. This
accessory allows manual operation of the garage door from outside in case of power failure.
CONTENTS PAGE
SAFETY INSTRUCTIONS 1
CARTON INVENTORY 3
TOOLS REQUIRED 3
DOOR REQUIREMENTS 3
CONTROL PANEL 4
PREPARE & TEST THE DOOR 5
PINNING THE DOOR 6
OPERATING MANUAL RELEASE 6
INSTALLATION PROCEDURE 7-8
ADJUSTMENT & TESTING 9
TIMER TO CLOSE 11
PROGRAM TRANSMITTER TO OPERATE OPENER LIGHT 11
PAGE
AUDIBLE BEEP 12
PARTIAL OPENING 12
WIRELESS PROGRAMMING 13
OPERATING YOUR OPENER 14
CARE OF YOUR OPENER 14
MAINTAINING YOUR OPENER 14
SPECIFICATIONS 14
WIRING 15
TROUBLESHOOTING 16
ACCESSORIES 17-18
DIAGNOSTIC CHART 18
WARRANTY 19-20

3
INTRODUCTION
CARTON INVENTORY
1
TOOLS REQUIRED
2
1. Ladder
2. Adjustable wrench for U-bolts already installed on the door
3. 8 mm socket, 10 mm socket and 13 mm extended socket
and socket wrench
4. 300 mm socket extension (for minimum side-room
installations)
5. Drill and 5.5 mm drill bit
6. Philips-head screwdriver
7. Marker pen
8. Rope
9. Door stand (not shown)
DOOR REQUIREMENTS
3
The RollerLift Plus (CR855MYQ) is suitable for spring balanced Residential Rolling garage doors with:
• Maximum door height of 4.5 m.
• Maximum curtain area of 16 m2.
• Maximum door mass of 100 kg.
*The Protector SystemTM (IR Beams) must be installed if the
force at the edge of the closing door exceeds 400N (40 kgf).
Door axle diameter must not exceed 35 mm.
Ensure that there is at least 45 mm from the edge of the curtain to the edge of the bracket. If the roller door drum wheel is on the
edge of the curtain or is a smaller diameter, additional clearance may be required.
Assemble the opener to the door axle and the existing door bracket using the U clamp assembly provided. Tighten to 25-28 Nm.
Full installation process is in section 12.
QuickStart Guide
Keepchildren away when the door is moving.
RISKOF ENTRAPMENT:
RepeatSafety Reverse Test
monthly.Door must reverse
oncontact with a 40mm
obstacleplaced on the floor.
Makenecessary adjustments.
AUTOMATICDRIVE:
Keepaway from the area
ofthe door since it may
operateunexpectedly.
EMERGENCYRELEASE:
Torelease, pull down
firmlyon the red handle.
132A3421
1. Instruction manual (this document)
2. Stop collar
3. Clamp bracket, plates, washers (2) and nuts (2)
4. E940C car visor transmitter (1)
5. E950C hand held transmitter (2)
6. Opener
7. Manual release handle and rope
8. Self tapping screws (2) (for pinning the door)
9. Weight bar screws (2), washers (2) and nuts (2)
10. Warning label and risk of entrapment label
11. Quick start guide
12. Weight bar
Marker Pen
8

4
INTRODUCTION
CONTROL PANEL
4
1. Terminal Block: used for external accessories (see chart below).
NOTE: The terminal block is behind a plastic cover in the back housing. Use a small screwdriver to lever open the plastic
cover if access to the terminal block is required. All wires should be secured appropriately.
2. DN Button: used to drive the door DOWN.
3. UP Button: used to drive the door UP.
4. P Button: used to “PROGRAM” the DOOR LIMITS (see section 13).
5. S Button: used to “SAVE” and “DELETE” the “TRANSMITTERS” (see section 20).
6. LEDs:
1. Program DOWN, and Diagnostic code indicator Number 1.
2. Program UP indicator.
3. Diagnostic code indicator Number 2.
7. Control Button: Used to activate the door when transmitters are not available. Open - Stop - Close.
8. Courtesy Light: turns on during operation and automatically turns off after a period of 3 minutes .
REF FUNCTION COLOUR POLARITY COMMENT
1Push button Red +ve Dry contact input for push button wired wall controls.
2 Common White -ve Common terminal for push button, The Protector SystemTM
(IR Beams) & accessory power.
3 Common White -ve Common terminal for push button, The Protector SystemTM
(IR Beams) & accessory power.
4The Protector SystemTM
(IR Beams)
Grey +ve The Protector SystemTM (IR Beams) input (pulsing type only
5Accessory power Green +ve 24v dc 50 mA accessory output available for a universal
receiver.
D
C
B
B
A
1
D
C
B
B
A
Remove theknock outlug required for
cableaccess to theterminalblock from
therearplastic cover.
DN UP PS
66
123
7
23 4 5
8

5
INSTALLATION
TESTING THE DOOR
5
Complete the following test to ensure your door is well balanced, and
not sticking or binding:
• Disable all locks and remove any ropes connected to the garage door.
• Lift the door to about halfway and then release it. The door should
remain spring balanced.
• Raise and lower the door to determine if there are any sticking or binding
points (20 kgf is the absolute maximum allowable to raise or lower the
door in any position).
If your door does not hold in place or the door binds or sticks, call a qualified
door technician before installing the opener.
ATTACHING THE STOP COLLAR
6
ATTACHING THE WEIGHT BAR
7
• The stop collar is required to be installed on the opposite side
of the door to where the opener is to be installed.
• Ensure the U-Bolt holding the door shaft to the door bracket is
tightly secure.
(NOTE: This U-Bolt must not be removed or loosened)
• Remove the bolt assembly from the plastic stop collar. Open
the collar as wide as possible and push it onto the door shaft.
• Fit the stop collar hard against the boss of the door drum.
Reinstall the bolt assembly onto the stop collar and tighten.
Nonopenerside Opener side
Boss 1
SAFETY CHECK!
Is the stop collar installed?
YES: proceedto the next
step
NO:install the stop collar
before proceeding
If the door has a lifting handle, remove the handle, nuts & bolts. Place the
weight bar over the handle holes, insert the extended bolts through the
weight bar & fasten the handle back in place.
• Place the weight bar in the centre of the door as shown.
If the door curtain does not have a handle you will need to follow these
instructions:
• Use a marker pen to mark the two hole positions.
• Drill two 5.5 mm holes through the two marked positions, then place the
weight bar on the inside of the door.
• Use the bolts, washers and nuts (provided) to fasten the weight bar in
place.

6
INSTALLATION
PINNNG THE DOOR
8
Note: A ballooning door may delay the safety reversal response
and can compromise garage door security.
• To remedy any ballooning, insert the supplied self tapping metal
screws (inset 3) into where the curtain leaves the roll. Secure
these through the curtain into the drum wheel at each end of
the roll.
• After determining the correct fastener location as shown, lift the
door approximately half a turn from the closed position to allow
access for securing the screws.
THE RELEASE HANDLE & CORD
9
OPERATING THE MANUAL RELEASE
10
The manual release mechanism enables the door to be manually
operated during power outages or in an emergency.
Thread the end of the rope through the loop of the manual release
cable.
Adjust rope length so the handle (when installed) will be no higher
than 1.8m above the floor. Secure with an overhand knot. If the
door is greater than 2.5m in height the release cord extension kit is
required.
NOTE: Final adjustment of handle height should be completed after
the opener is installed. If it is necessary to cut the rope, heat seal
the cut end to prevent unravelling.
To disengage the opener
Pull the release cord down firmly,
(the opener will make a clicking noise).
To re-engage the opener
Pull the release cord down firmly,
(the opener will make a clicking noise).
Free curtain Ballooning Add fasteners here
Door closed Door canbe
lifted
Doorsecure
3
Rope
Manual release
warninglabel
Release handle
Overhand knot
Overhan
dknot
Disable all locks and remove any ropes connected to the garage door.
Take care when operating the manual release as an open door may fall rapidly due to weak or broken springs, or
being out of balance.
Do not disengage the opener to manual operation
with children, persons or other objects including
motor vehicles within the doorway. The door is
under significant tension and if the door has
developed a fault or incorrect tension, it may be
unsafe and may fall rapidly.
Rope
Manual release
warninglabel
Release handle
Overhand knot
Overhandknot

7
INSTALLATION
LEFT/RIGHT HAND INSTALLATION
11
Inside garage lookingout
LEFT
(handing must
be changed
during limit
setting - refer to
section 13)
RIGHT
(factory
default
setting)

8
INSTALLATION
INSTALLATION PROCEDURE
12
NOTE: The opener can be installed on either side of the door.
The following instructions are for RIGHT HAND
INSTALLATIONS (as illustrated i.e. inside the garage looking
out). For left hand installations, reverse the instruction
terminology (eg LEFT for RIGHT etc).
Preparation:
• Place the opener in manual release mode (refer to section 10).
• Completely open the roller door. For safety, tie a rope around
the door.
• Ensure the door axle U-BOLT and door mounting bracket on the
left hand side (non opener side) are securely fastened.
• Support the door with a door stand, ladder or similar device to
safely support the door.
• Mark the position of the door shaft on the right hand door
bracket (for reassembly purposes).
• While the door is supported, remove the right hand axle U-Bolt
and door mounting bracket from the wall.
Install the opener:
• Slide the opener over the door axle and engage the drive legs
into the door drum wheel, either side of a spoke.
• Refit the door mounting bracket to the wall.
• Clamp the opener on the door axle and door bracket in the
marked position using the clamp assembly supplied (tighten to
25 – 28 Nm).
• Remove all ropes and the support stand.
• Check the operation of the door in manual mode by raising and
lowering by hand. It should operate smoothly without sticking or
binding. The disengage handle should already be attached less
than 1.8m above the floor (refer to section 9).
Connect the power:
• Position the power cable away from the door curtain and any
moving parts.
• Plug the opener into a nearby power point and turn ON.
• The opener light will turn ON and remain ON for 3 minutes.
Do not allow people to walk under or around the
door during the installation process as serious
injury can occur.
Rope
Ladder
Rope
Ladder
Tighten to
25-28 Nm

9
INSTALLATION
SETTING THE LIIMITS FOR RIGHT OR LEFT HAD OPERATION AND FORCE
13
Setting the Right or Left Hand Operation:
Refer to the diagrams on the right for guidance.
Ensure the door is positioned halfway and the opener is engaged
(out of manual mode).
Turn the opener Power ON, the courtesy light will turn ON.
1. Press the “P” button for 5 seconds until LED 3 will flash, as well
as LED 2 or LED 1 will flash. For Right Hand setting LED 2 will
flash, and for Left Hand setting LED 1 will flash.
2. To change to the opposite setting, simply press the “S” button,
and the opposite LED will flash.
3. When the correct hand setting is selected, Press and Release
the “P” program button to accept this setting. (continue).
Setting the Door Limits:
Press and hold the “UP” button until the door
reaches the desired OPEN position (You can toggle between
the “UP” and “DN” buttons to move the door to the correct
position. Ensure the bottom rail stops 50 mm below the
mechanical stops mounted to the door guides).
4. Press and release the “P” program button to
accept this setting.
5. Press and hold the “DN” button until the door reaches the
desired CLOSED position (You can toggle between the UP and
DN buttons to move the door to the correct position).
6. Press and release the “P” program button to accept this setting.
(LED 2 should flash to indicate you are now in Force Learn
mode).
Setting the Force Automatically:
7. Press and release the “UP” button. The door will travel to the
OPEN position with LED 2 flashing.
8. Press and release the “DN” button. The door will travel to the
CLOSED position with LED 1 flashing. When fully closed, LED
1 will stop flashing and the courtesy light will change to full
power.
This process is now complete
Setting the Force manually: (Only perform if Limits are already
set)
• Start with the door fully CLOSED.
• Press the “S” button twice to enter into force learn mode. The
courtesy light will go to half strength, and LED 2 will flash
quickly.
• Press and release the “UP” button. The door will travel to the
OPEN position, then LED 1 will flash quickly.
• Press and release the “DN” button. The door will travel to the
CLOSED position, then LED 1 will stop and the courtesy light
will change to full power.
This process is now complete.
the opener will operate during this procedure. Make sure the door is clear of obstruction. Ensure your hands
are away from any moving parts before activating the door.
Travel limits set how far your door goes up and down. Your opener must also be configured for right or left hand installation. If not
the door will rotate in the reverse direction.
Program Buttons: The Control Panel diagram in section 4 identifies the Control Buttons and LED layout
Audible Beep: An audible “BEEP” also occurs with each button press. This feature can be turned OFF
Courtesy light: During the programming sequence, the courtesy light will flash at half strength
NOTE: The RollerLift Plus (CR855MYQ) opener is factory configured for right hand installation.
DN UP PS
123
1. Program
Start
2. Left/Right
Setting
3. Accept
Setting
4. Set UP
Limit
5. Accept UP
Limit
6. Set DOWN
Limit
7. Accept
DOWN
Limit
8. LearnUP
Force
9. Learn
DOWN
Force
Flashx2
BEEP
DOWN
DOWN
UP
UP
Flashx2
BEEP
Flashx2
BEEP
Flashx2
BEEP
Full light
BEEP
Flashx2
BEEP
Flashx2
BEEP
DN UP PS
123
DN UP PS
123
DN UP PS
123
DN UP PS
123
DN UP PS
123
DN UP PS
123
DN UP PS
123
DN UP PS
123

10
INSTALLATION
TESTING THE SAFETY REVERSE SYSTEM
14
Operate the door in the down direction. The door must reverse upon
contact with the obstacle. If the door stops on the obstacle, remove
obstacle and repeat limit and force setting (refer to section 13).
Repeat the safety reverse system test.
FIXING WARNING LABELS
15
Once you have completed your installation and successfully carried
out the safety reverse system test (outlined above), install the
warning labels provided with your opener as shown.
The risk of entrapment WARNING label MUST be installed
adjacent to the release handle at a height of less than 1.8 m from
the floor in a prominent place.
Any fixed wall control or wireless door control must be mounted at a
height of no less than 1.5 m out of the reach of children.
Read the safety instructions (page 2) for further details concerning
safety.
The safety reverse system test is important. The
garage door must reverse on contact with a 40
mm obstacle laid flat on the floor. Failure to
properly adjust the opener may result in serious
personal injury from a closing garage door.
40 mm Test obstacle
40 mm T
Keepchildren away when the door is moving.
RISKOF ENTRAPMENT:
RepeatSafetyReverse Test
monthly.Doormust reverse
oncontactwith a 40mm
obstacleplacedon the floor.
Makenecessaryadjustments.
AUTOMATICDRIVE:
Keepawayfrom the area
ofthedoor since it may
operateunexpectedly.
EMERGENCYRELEASE:
Torelease,pull down
firmlyonthe red handle.
132A3421
Keep children away when the door is moving.
RISK OF ENTRAPMENT:
Repeat Safety Reverse Test
monthly. Door must reverse
on contact with a 40mm
obstacle placed on the floor.
Make necessary adjustments.
AUTOMATIC DRIVE:
Keep away from the area
of the door since it may
operate unexpectedly.
EMERGENCY RELEASE:
To release, pull down
firmly on the red handle.
132A3421
STANDARD INSTALLATION COMPLETE