Chamberlain SMART GARAGE MYQ-G0301 User manual

QUICK START
GUIDE
MYQ-G0301 • MYQ-G0301C
MYQ-G0301D • MYQ-G0301LA
by
SMART
GARAGE™
HUB

CONNECT AN APPLE® iOS DEVICE
CONNECTER UN APPAREIL APPLE® iOS
CONECTE UN DISPOSITIVO APPLE® iOS
iOS users please
read before
installation
If you are using an iOS
device, follow these
instructions instead of
step 4. in the manual:
Utilisateurs iOS
lire avant
l’installation
Si un appareil iOS
est utilisé, suivre ces
instructions au lieu de
l’étape 4 dans le manuel :
Usuarios de iOS
leer antes de
instalar
Si está utilizando un
dispositivo iOS, siga estas
instrucciones en lugar
del paso 4 del manual:
Make sure the blue
LED on the Wi-Fi
Hub is blinking.
Vérier que la DEL bleue
sur le concentrateur
Wi-Fi clignote
Asegúrese de que el
LED azul en el Hub Wi-Fi
esté parpadeando.
On your mobile device,
go to Settings > Wi-Fi and
select the network with
the “MyQ-nnn” prex.
Sur votre appareil
mobile, allez à Settings
(Paramètres) > Wi-Fi et
sélectionnez le réseau
portant le préxe
« MyQ-nnn ».
En su dispositivo
móvil, vaya a Settings
(Ajustes) > Wi-Fi y luego
seleccione la red con el
prejo “MyQ-nnn”.
Launch the web browser
on your smartphone or
tablet. Enter
setup.myqdevice.
com into the browser
address bar. Follow the
on-screen prompts to
connect the Wi-Fi Hub
to your Wi-Fi network.
Lancez le navigateur
Web sur votre téléphone
intelligent ou votre
tablette. Saisissez
setup.myqdevice.com
dans la barre d’adresse
du navigateur. Suivez
le menu à l’écran
pour connecter le
concentrateur Wi-Fi
au réseau Wi-Fi de
votre domicile.
Abra el navegador web
en el teléfono inteligente
o en la tableta. Escriba
setup.myqdevice.com
en la barra de dirección
del navegador. Siga
las indicaciones
en la pantalla para
conectar el Hub Wi-Fi
a su red de Wi-Fi.
Download the MyQ®
app, set up an account
and add the MyQ serial
number (located on the
cover of the manual)
to your account.
Télécharger l’application
MyQ, créer un compte
et ajouter le numéro
de série MyQ à votre
compte (situé sur la page
couverture du manuel).
Descargue la aplicación
MyQ, congure una
cuenta y agregue el
número de serie de MyQ
(ubicado en la cubierta
del manual) a su cuenta.
1
2
3
4
Apple is a trademarks of Apple Inc.,
registered in the U.S. and other countries.
© 2017, The Chamberlain Group, Inc.
All Rights Reserved
Tous droits réservés
Todos los Derechos Reservados
114A4987B

To reduce the risk of SEVERE INJURY to persons:
• DO NOT enable the MyQ® SMART GARAGE™ HUB if operating
either one-piece or swinging doors. To be enabled ONLY on a
sectional door.
Read instructions thoroughly BEFORE beginning.
If using this product with residential door openers, this product
must be used only with door openers manufactured after 1993
that utilize photoelectric sensors. The photoelectric sensors are
always located on or near the bottom of the door track.
To see a list of compatible garage door openers go to:
www.chamberlain.com/MyQCompatibility
BEFORE YOU START, YOU MUST HAVE…
Compatible garage
door opener
A router
with 2.4GHz
Wi-Fi®
Mobile device
connected to your
home Wi-Fi network

Tools Needed: Drill, 5/32" Drill Bit, Screwdriver, Ladder
Wi-Fi Hub
Blue LED
Green LED
Yellow LED
Power Adapter
Mounting bracket
Warning Label
(not shown)
Hardware for Wi-Fi Hub
(5/32" x 1-1/2" screws)
What’s in the Box

Hardware for
Door Sensor
(5/32" x 3/4" screws)
Fastening Strips for
Door Sensor
Door Sensor
Model MYQ-G0302
Red
LED
Test
Button

Install
1. Check your Wi-Fi
(mounting area)
• Check the Wi-Fi signal in the garage, where the Wi-Fi Hub will be
mounted.
• Make sure you have two or more Wi-Fi bars.
NOTE: If there are signal strength issues, please visit
https://www.chamberlain.com/wisupportvideos for instructional
videos.

• Remove the pull tab from the sensor
to activate the battery.
• Install the door sensor on the top
panel of the garage door using the
fastening strips or provided hardware.
TIP: Test your door sensor every 6 months
or if the MyQ system is not working as
expected.
• Press the test BUTTON on the door
sensor, the LED on the door sensor
should flash and the Wi-Fi Hub should
beep.
• Perform this test 6 times. If the LED
doesn’t flash or the Wi-Fi Hub doesn’t
beep each time, replace the battery in
the door sensor with a CR2450 battery.
2. Install the Door Sensor
Door Sensor
OR
Screws
LED
Test
BUTTON
“TOP” MUST
always face UP
Fastening
Strips

Install
• Find a convenient location
and power the Wi-Fi Hub by
plugging it in. The blue LED
will start blinking.
3. Power Up the Wi-Fi Hub
• Download the
Chamberlain MyQ® App.
• Create or sign-in to your
account and follow the
in-app instructions.
4. MyQ® App Setup
Blue LED blinks
Download
App

• After successfully completing all of the steps in the Chamberlain MyQ®
App, install the Wi-Fi Hub on the ceiling, near the garage door opener.
• Plug it in and make sure the green LED turns on solid.
• Wi-Fi Hub light MUST be visible if you’re standing in the doorway of
the garage.
Wi-Fi Hub
Warning
Label
Door Control
TIP: Wrap excess power
adapter cable around
the mounting bracket.
• Attach the warning label to the wall next to the door control.
6. Apply Warning Label
5. Install the Wi-Fi Hub

Need Help?
Go to: www.chamberlain.com/MyQSupport
One Year Limited Warranty
The Chamberlain Group, Inc. warrants to the first consumer
purchaser of this product that it is free from defect in materials and/
or workmanship for a period of 1 year from the date of purchase.
Software Agreement
Use of this product and the software embedded within the product is subject to
the copyright notices, terms, and conditions available at:
http://www.mychamberlain.com/agreement
NOTICE: This device complies with Part 15 of the FCC rules and Industry Canada’s license-exempt RSSs.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
This device must be installed to ensure a minimum 20 cm (8 in.) distance is maintained between users/
bystanders and device.
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC rules and Industry Canada ICES standard. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

CONCENTRATEUR
SMART
GARAGE™
GUIDE DE
DÉMARRAGE
RAPIDE
MYQ-G0301 • MYQ-G0301C
MYQ-G0301D • MYQ-G0301LA
by