Channel Safety Systems Wyvern User manual

CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk
INSTRUCTION MANUAL - Issue 1 - 02/2014 | 1
INSTRUCTION MANUAL
CHANNEL SAFETY SYSTEMS t: 0845 884 7000
Peterseld Business Park f: 0845 884 6000
Bedford Road
Peterseld
Hampshire e: [e-mail]
GU32 3QA w: www.channelsafety.co.uk
Conventional uorescent and
emergency luminaire
from Channel Safety Systems
Wyvern

CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk
INSTRUCTION MANUAL - Issue 1 - 02/2014 | 2
WYVERN CONVENTIONAL EMERGENCY LUMINAIRE
MOUNTING AND WIRING
The luminaire is suitable for both Indoor and Outdoor applications - Please make reference to the diagram below for Luminaire Assembly details.
SPECIFICATION
IP Rating IP65
Battery Voltage 2.4V 4mAh
Duration 3 hours
Battery Format 1 x 2 cells (4.4AH Nickel-Cadmium)
Lamp 8W 12" T5
Ballast Lumen Factor 0.25
Rated lumen Output 65 lumens
Rated Supply Voltage 230V 50Hz ±10%
Supply current 70mA (max)
Charging current 0.17-0.3 A
Discharge current 1.15 A Nominal
Ambient temperature range 0°C to +30°C and up to 80% Relative Humidity
Max continuous cell temp for 4-year battery life. 55ºC
Standards EN60598-2-22:1999, EN55015:1996, EN61547:1996
Weight 1.3Kg
Remove diffuser retaining screws
Remove hinged geartray-retaining screws
BESA box mounting option
Cable entry option
Drill start wall fixing
Cable entry option
Connect battery to the PCB on emergency luminaries before re-tting gear tray.
The luminaire should be mounted using the xing holes provided, on a sound at surface. If the luminaire is to be used in a weatherproof application, Please
ensure that all cable entry and xing points are suitably sealed. Route the incoming cables around the outside of the body well away from the control gear,
and make-o the conductors in the gear-tray mounted terminal block.

CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk
INSTRUCTION MANUAL - Issue 1 - 02/2014 | 3
MOUNTING AND WIRING CONTINUED...
COMMISSIONING (EMERGENCY LUMINAIRE)
Follow the procedure below to establish that the luminaire is working correctly.
• Connect the batteries to the Printed circuit board using the ying plug and socket.
• The permanent live supply should be switched on, and the LED should light, this indicates the batteries are charging.
• Turn On the normal lighting supply (if a Switched Live supply is present), the lamp should light.
• Leave the luminaire in this state for at least one hour before failing all live supplies. The lamp should light in the emergency mode at reduced brightness.
• Restore the mains supply and leave the luminaire to fully charge the batteries, this will normally be 24 hours. It is nevertheless advisable, to allow an
initial charge of 48 hrs before putting the batteries into service for the rst time.
The date that this is carried out must be marked in the space provided on the battery label.
Connect to the terminals as follows;
Safety earth conductor
Lch Live charge conductor (Permanent Live supply)
NNeutral conductor
Lsw Live switched conductor (Switched Live supply)
If Non-maintained operation is required, connect a permanent live supply to the Lch terminal only (See the diagram below for further guidance).
Typical wiring diagram (Mains & Emergency luminaire)
Earth
Neutral
Live
N N N Lsw Lsw Lsw Lch Lch
NC
Wall Switch
Mains Only
Luminaire
Maintained
Luminaire
Non-Maintained
Luminaire
Optional key
operated test facility
or other test device

CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk
INSTRUCTION MANUAL - Issue 1 - 02/2014 | 4
Luminaire Location: .....................................................................................................................................................................
In Case of Fault Contact: ..............................................................................................................................................................
Duration 3 Hours Tube Type: 8 Watts ..........................................................................................................................................
FIRST YEAR SECOND YEAR THIRD YEAR FOURTH YEAR FIFTH YEAR
MONTH TEST SIGN DATE SIGN DATE SIGN DATE SIGN DATE SIGN DATE
1 Functional
2 Functional
3 Functional
4 Functional
5 Functional
6 Functional
7 Functional
8 Functional
9 Functional
10 Functional
11 Functional
12 3 hour
TESTING
The luminaire must be checked periodically for correct operation, and to evaluate the remaining capacity in the battery at regular intervals during its life. The
unswitched supply should be failed which will cause the luminaire to operate in the emergency mode.
• The LED charge indicator should be checked on a daily basis.
• Every month the luminaire should be tested in the emergency mode to ensure the lamp is illuminated.
• Annually the luminaire should be tested to ensure it achieves its entire rated duration of emergency operation.
• Record the periodic testing of individual luminaire in the table below, and keep all records in a safe place.
IF THE LUMINAIRE FAILS TO ACHIEVE ITS RATED DURATION, THE BATTERIES MUST BE REPLACED, OF AN IDENTICAL
TYPE, SEE THE LABEL ON THE BATTERY FOR THE ORDER REFERENCE.
FLUORESCENT TUBES MUST BE CHANGED AT THE FIRST SIGNS OF BLACKENING.

CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk
INSTRUCTION MANUAL - Issue 1 - 02/2014 | 5

INSTRUCTION MANUAL
CHANNEL SAFETY SYSTEMS t: 0845 884 7000
Peterseld Business Park f: 0845 884 6000
Bedford Road
Peterseld
Hampshire e: [e-mail]
GU32 3QA w: www.channelsafety.co.uk