Channel Vision 6544 User manual

6544
1.3 Megapixel Bullet Wireless IP Camera w/35 IR Illuminators

Table Of Contents

The 6544 is a 1.3 Megapixel Bullet Wireless IP Camera w/35 IR Illuminators
Built-in web server allows users to view high quality, real-time video with Internet Explorer browser.
Multi-Stream H.264, MJPEG and MPEG
Live video can be recorded to a NVR and played back remotely, as well as viewed from many mobile
phones and other devices.
Designed for large commercial projects with 100’s of cameras or a single family house requiring a
camera at the front door.
Wireless connectivity, using WEP, WPA-PSK, and WPA2-PSK
Hidden cable through the mount
Android & iPhone app
Adjustable Varifocal Lens 3.3-12mm
Alarm Trigger input and N.O. or N.C. switch on relay output
36 Camera CMS (Central Management) which will allow you to see all of your cameras anywhere in the
world in multiple locations at the same time
6544 Features:
Channel Vision’s 6544 IP Bullet camera offers superior image quality with a 1.3 megapixel CMOS sensor
and has the ability to capture images up to 1280 x 800 pixels.
With H.264 compression, less bandwidth and storage space are used, while delivering full resolution at
max frame rate with faster speeds over the internet.
The 6544 also features event triggered motion recording, as well as 35 IR LED for a viewing distance of
60 feet in total darkness. Monitoring can be done anywhere an internet connection is available even
from a Smart-phone. The 6544 also features wireless communication using WEP, WPA-PSK, and
WPA2-PSK.
Model 6544
6544
•
•
•
•
•
•
•
•
•
•
3

Safety Warnings
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions for future reference.
3. Heed all warnings.
4. Follow all instructions.
5. Clean only with a dry cloth.
6. Install in accordance with these instructions.
7 Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
that produce heat.
8. Do not defeat the safety purpose of the polarized-type plug. A polarized plug has two blades with
one wider than the other. The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete
outlet.
9. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point of exit from the apparatus.
10. Only use attachments/accessories specified by Channel Vision.
11. Unplug this apparatus during lightning storms or when unused for long periods of time.
12. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the inside of the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
13. The lightning flash with an arrowhead symbol within an equilateral triangle is intended to alert the
user to presence of uninsulated dangerous voltage within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
14. The exclamation point within an equilateral triangle is intended to alert the user to the presence
of important operating and maintenance accompanying the appliance.
15. Inside of apparatus shall not be exposed to dripping or splashing and objects filled with liquids.
CAUTION: To reduce the risk of electric shock,
do not remove the cover (or back). There are no
user-serviceable parts inside, refer servicing to
qualified service personnel.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISK OF ELECTRIC SHOCK
DO NOT OPEN !
4

The breakout cable on Channel Vision’s IP Cameras are used for motion detection, event
triggering, alarm notifications etc.
The provided interface connections are explained below.
1. Digital Input (GND+DI):
An alarm input for connecting devices that can toggle between an open and closed circuit, for
example PIRs, door/window contacts, broken glass detectors, etc. When a signal is received, the
state changes and the input becomes active.
2. Relay output (GND+DO)
A selectable output for a relay switch, for example LEDs, Sirens, etc.
Normally Open and Normally Closed can be selected via the Internet Explorer ActiveX control
under the “I/O Setting” section on the left.
3. Reset to factory default
To restore your IP camera to Channel Vision default settings, place one side of a stripped jumper
wire in to the “Default” terminal on the connector.
Then, place the other side of that cable into to “GND” terminal.
Plug in power cable. Once camera has restarted, remove the electric wire and plug in the Ethernet
cable. Use IP installer to find the camera IP. (Default is http://192.168.1.200) Default username and
password is “admin”
Cable Pin Out
VDC 12 VDC 12
O T alI/ ermin O T alI/ ermin
Ethernet Connector
(T568B Standard)
Ethernet Connector
(T568B Standard)
WARNING
DO NOT CUT THE BREAKOUT CABLE.
CUTTING THE CABLE WILL VOID THE WARRANTY ON THE DEVICE.
Default
GND
D.O
GND
D.I
5

Your IP Camera comes set to DHCP by default. This means that, just like your laptop computer or desktop PC, an IP
address is automatically assigned to the IP camera by your router. This, combined with UPnP (Universal Plug and
Play), will make the IP setup of the IP camera quick and easy to accomplish.
*For the best security, Channel Vision recommends you use a static IP setting and standard port forwarding.
1. Open IP installer. This is located on your software disk under the folder “\CVT IP Installer
2. An IP address should already be assigned
In the example below, the router has assigned 192.168.1.219 to the IP Camera
3. Double click on the name of the IP Camera. This will open the IP camera in your default browser
Option One: Assigning an IP Address (DHCP)
6

Connecting To The IP Camera (DHCP)
5. The first time you connect to the camera via Internet Explorer, it will ask you to install the ActiveX control.
Internet Explorer 6, 7, 8, or 9 must be used to run this ActiveX control.
4. You will be prompted for a username and password.
The default username is ‘admin’
The default password is ‘admin’
Installing The ActiveX Control
7

1. Use the software, “IP Installer” to assign the IP address to your IP Camera. You can find "IP
Installer" in the supplied CD.
2. Execute IP Installer, located on your disk under the folder “Software”
3. If Windows prompts you to unblock IP Installer, you must select “unblock”
There are 3 options of IP configuration:
A. Fixed IP (Public IP or Virtual IP)
B. DHCP (Dynamic IP)
C. Dial-up/DSL (PPPoE)
"IP Installer" will search all IP Cameras connected to your LAN network.The user can
click “Search Device” to search again.
Double click the camera name to go directly to the camera
Option Two: Assigning an IP Address (Static)
8

Assigning an IP Address (Static) /cont
4. Click the start icon on your computer.
5. Type the word “run” and select enter on your keyboard.
6. Type in ‘cmd’ and press enter on your keyboard, or press ok.
7. Type in ‘ipconfig /all’ into the DOS prompt that appears. Press “Enter”.
8. Write down your computer’s IP address.
Do not use the same IP address as the computer in the IP Camera.
In the example below, the computer’s IP address is 192.168.1.74.
The IP address of the IP camera must be different than the IP address in the computer.
Each network-able device in your network has an IP address assigned.
The IP chosen for your IP Camera is not the same address as any other device on your network.
9

9. Copy/write down the following information from the DOS prompt.
A. Default Gateway (Example 192.168.1.1)
B. DNS Server (if 2 servers, use the first one, for example 192.168.1.9)
C. Subnet Mask (Example 255.255.255.0)
10
Assigning an IP Address (Static) /cont